QUINT4-PS/3AC/24DC/40 - Power supply - 2904623

Input data

Control input (configurable) Rem	Output power ON/OFF (SLEEP MODE)
Default	Output power ON (>40 kΩ/24 V DC/open bridge between Rem and SGnd)
AC operation
Network type	Star network
Nominal input voltage range	3x 400 V AC ... 500 V AC
Nominal input voltage range		2x 400 V AC ... 500 V AC
Input voltage range	3x 400 V AC ... 500 V AC -20 % ... +10 %
Input voltage range		2x 400 V AC ... 500 V AC -10 % ... +10 %
Typical national grid voltage	400 V AC
Typical national grid voltage		480 V AC
Voltage type of supply voltage	AC/DC
Inrush current	typ. 1.5 A (at 25 °C)
Inrush current integral (I²t)	< 0.06 A²s
Inrush current limitation	1.5 A (after 1 ms)
AC frequency range	50 Hz ... 60 Hz -10 % ... +10 %
Frequency range (f_N)	50 Hz ... 60 Hz -10 % ... +10 %
Mains buffering time	typ. 28 ms (3x 400 V AC)
Mains buffering time		typ. 28 ms (3x 480 V AC)
Current consumption	3x 1.8 A (400 V AC)
		3x 1.5 A (480 V AC)
		2x 3 A (400 V AC)
		2x 2.5 A (480 V AC)
		3x 1.5 A (500 V AC)
		2x 2.4 A (500 V AC)
Nominal power consumption	1217 VA
Protective circuit	Transient surge protection; Varistor, gas-filled surge arrester
Power factor (cos phi)	0.95
Switch-on time	< 1 s
Typical response time	300 ms (from SLEEP MODE)
Recommended breaker for input protection	3x 4 A ... 20 A (Characteristic B, C, D, K or comparable)
Recommended fuse for input protection	≥ 300 V AC
Discharge current to PE	< 3.5 mA
Discharge current to PE		1 mA (550 V AC, 60 Hz)
DC operation
Nominal input voltage range	± 260 V DC ... 300 V DC
Input voltage range	± 260 V DC ... 300 V DC -13 % ... +30 %
Input voltage range		520 V DC ... 600 V DC -13 % ... +30 % (mid-point earthed)
Current consumption	2.2 A (±260 V DC)
Current consumption		1.9 A (±300 V DC)
Nominal power consumption	1217 VA
Recommended breaker for input protection	1x 6 A (10 x 38 mm, 30 kA L/R = 2 ms)
Recommended fuse for input protection	≥ 1000 V DC

Output data

Efficiency	typ. 95.7 % (400 V AC)
Efficiency		typ. 95.7 % (480 V AC)
Nominal output voltage	24 V DC
Setting range of the output voltage (U_Set)	24 V DC ... 29.5 V DC (constant capacity)
Nominal output current (I_N)	40 A
Static Boost (I_Stat.Boost)	45 A
Dynamic Boost (I_Dyn.Boost)	60 A (5 s)
Selective Fuse Breaking (I_SFB)	215 A (15 ms)
Magnetic circuit breaker tripping	A1...A40 / B2...B25 / C1...C13 / Z1...Z16
Derating	> 60 °C ... 70 °C (2.5 %/K)
Feedback voltage resistance	≤ 35 V DC
Protection against overvoltage at the output (OVP)	≤ 32 V DC
Control deviation	< 0.5 % (Static load change 10 % ... 90 %)
		< 3 % (Dynamic load change 10 % ... 90 %, (10 Hz))
		< 0.25 % (change in input voltage ±10 %)
Residual ripple	< 50 mV_PP (with nominal values)
Short-circuit-proof	yes
No-load proof	yes
Output power	960 W
		1080 W
		1440 W
Maximum no-load power dissipation	< 5 W (400 V AC)
Maximum no-load power dissipation		< 5 W (480 V AC)
Power loss nominal load max.	< 45 W (400 V AC)
Power loss nominal load max.		< 45 W (480 V AC)
Power dissipation SLEEP MODE	< 2 W (400 V AC)
Power dissipation SLEEP MODE		< 2 W (480 V AC)
Crest factor	typ. 1.6 (400 V AC)
Crest factor		typ. 1.9 (480 V AC)
Rise time	< 1 s (U_Out = 10 % ... 90 %)
Connection in parallel	yes, for redundancy and increased capacity
Connection in series	yes
Signal
Signal ground SGnd	Reference potential for Out1, Out2, and Rem
Signal Out 1 (configurable)
Digital	24 V DC 20 mA
Default	24 V DC 20 mA 24 V DC for U_Out > 0.9 x U_Set
Signal Out 2 (configurable)
Digital	24 V DC 20 mA
Analog	4 mA ... 20 mA ±5 % (Load ≤400 Ω)
Default	24 V DC 20 mA 24 V DC for P_Out < P_N
Signal relay 13/14 (configurable)
Default	closed (U_out > 0.9 U_Set)
Digital	24 V DC 1 A
Digital		30 V AC/DC 0.5 A

Connection data

Input
Connection method	Screw connection
Conductor cross section, rigid min.	0.2 mm²
Conductor cross section, rigid max.	6 mm²
Conductor cross section flexible min.	0.2 mm²
Conductor cross section flexible max.	4 mm²
Single conductor/flexible terminal point with ferrule with plastic sleeve, min.	0.25 mm²
Single conductor/flexible terminal point with ferrule with plastic sleeve, max.	4 mm²
Single conductor/flexible terminal point with ferrule without plastic sleeve, min.	0.25 mm²
Single conductor/flexible terminal point with ferrule without plastic sleeve, max.	4 mm²
Conductor cross section AWG min.	24
Conductor cross section AWG max.	10
Stripping length	8 mm
Tightening torque, min	0.5 Nm
Tightening torque max	0.6 Nm
Output
Connection method	Screw connection
Conductor cross section, rigid min.	0.5 mm²
Conductor cross section, rigid max.	16 mm²
Conductor cross section flexible min.	0.5 mm²
Conductor cross section flexible max.	16 mm²
Single conductor/flexible terminal point with ferrule with plastic sleeve, min.	0.5 mm²
Single conductor/flexible terminal point with ferrule with plastic sleeve, max.	16 mm²
Single conductor/flexible terminal point with ferrule without plastic sleeve, min.	0.5 mm²
Single conductor/flexible terminal point with ferrule without plastic sleeve, max.	16 mm²
Conductor cross section AWG min.	20
Conductor cross section AWG max.	6
Stripping length	10 mm
Tightening torque, min	1.2 Nm
Tightening torque max	1.5 Nm
Signal
Connection method	Push-in connection
Conductor cross section, rigid min.	0.2 mm²
Conductor cross section, rigid max.	1 mm²
Conductor cross section flexible min.	0.2 mm²
Conductor cross section flexible max.	1.5 mm²
Single conductor/flexible terminal point with ferrule with plastic sleeve, min.	0.2 mm²
Single conductor/flexible terminal point with ferrule with plastic sleeve, max.	0.75 mm²
Single conductor/flexible terminal point with ferrule without plastic sleeve, min.	0.2 mm²
Single conductor/flexible terminal point with ferrule without plastic sleeve, max.	1.5 mm²
Conductor cross section AWG min.	24
Conductor cross section AWG max.	16
Stripping length	8 mm

Signaling

Signal output
P_Out	> 100 % (LED lights up yellow, output power > 960 W)
	> 75 % (LED lights up green, output power > 720 W)
	> 50 % (LED lights up green, output power > 480 W)
U_Out	> 0.9 x U_Set (LED lights up green)
	< 0.9 x U_Set (LED flashes green)

Electrical properties

Number of phases	3
Insulation voltage input/output	4 kV AC (type test)
	2.4 kV AC (routine test)
Insulation voltage output / PE	0.5 kV DC (type test)
	0.5 kV DC (routine test)
Insulation voltage input / PE	3.5 kV AC (type test)
	2.4 kV AC (routine test)
Switching frequency	32.00 kHz ... 100.00 kHz (Auxiliary converter stage)
	55.00 kHz ... 300.00 kHz (Main converter stage)
	25.00 kHz ... 500.00 kHz (PFC stage)

Product properties

Product type	Power supply
Product family	QUINT POWER
MTBF (IEC 61709, SN 29500)	> 849000 h (25 °C)
		> 517000 h (40 °C)
		> 236000 h (60 °C)
Environmental protection directive	RoHS Directive 2011/65/EU
		WEEE
		Reach
Insulation characteristics
Protection class	I
Degree of pollution	2
Life expectancy (electrolytic capacitors)
Current	20 A
Temperature	40 °C
Time	394000 h
Additional text	400 V AC
Life expectancy (electrolytic capacitors)
Current	20 A
Temperature	40 °C
Time	367000 h
Additional text	480 V AC
Life expectancy (electrolytic capacitors)
Current	40 A
Temperature	25 °C
Time	394000 h
Additional text	400 V AC
Life expectancy (electrolytic capacitors)
Current	40 A
Temperature	25 °C
Time	367000 h
Additional text	480 V AC
Life expectancy (electrolytic capacitors)
Current	40 A
Temperature	40 °C
Time	139000 h
Additional text	400 V AC
Life expectancy (electrolytic capacitors)
Current	40 A
Temperature	40 °C
Time	130000 h
Additional text	480 V AC

Dimensions

Width	120 mm
Height	130 mm
Depth	125 mm
Installation dimensions
Installation distance right/left	5 mm / 5 mm
Installation distance top/bottom	50 mm / 50 mm

Mounting

Mounting type	DIN rail mounting
Mounting position	horizontal DIN rail NS 35, EN 60715
With protective coating	no

Material specifications

Flammability rating according to UL 94 (housing / terminal blocks)	V0
Housing material	Metal
Hood version	Stainless steel X6Cr17
Side element version	Aluminum

Environmental and real-life conditions

Ambient conditions
Degree of protection	IP20
Ambient temperature (operation)	-25 °C ... 70 °C (> 60 °C Derating: 2,5 %/K)
Ambient temperature (storage/transport)	-40 °C ... 85 °C
Ambient temperature (start-up type tested)	-40 °C
Maximum altitude	≤ 5000 m (> 2000 m, observe derating)
Climatic class	3K3 (in acc. with EN 60721)
Max. permissible relative humidity (operation)	≤ 95 % (at 25 °C, non-condensing)
Shock	11 ms, 15 g, in each space direction (according to IEC 60068-2-27)
Vibration (operation)	5 Hz ... 100 Hz resonance search 0.7g, 90 min., resonance frequency 0.7g, 90 min. (in accordance with DNV GL Class A) 5 Hz ... 100 Hz resonance search 2.3g, 90 min., resonance frequency 2.3g, 90 min. (according to DNV GL Class C) mounted with UWA 130 - 2901664
Temp code	T4 (-25 ... +70 °C; > 60 °C, Derating: 2,5 %/K)

Standards and regulations

Rail applications	EN 50121-3-2
		EN 50121-5
		IEC 62236-3-2
		IEC 62236-5
HART FSK Physical Layer Test Specification Compliance	Output voltage U_Out compliant
Standard – Limitation of mains harmonic currents	EN 61000-3-2
Standard - Electrical safety	IEC 61010-2-201 (SELV)
Standard – Safety extra-low voltage	IEC 61010-1 (SELV)
Standard – Safety extra-low voltage		IEC 61010-2-201 (PELV)
Standard - Safe isolation	IEC 61558-2-16
Standard - Safe isolation		IEC 61010-2-201
Standard - safety for equipment for measurement, control, and laboratory use	IEC 61010-1
Standard - Safety of transformers	EN 61558-2-16
Battery charging	DIN 41773-1
Approval - requirement of the semiconductor industry with regard to mains voltage dips	SEMI F47-0706, EN 61000-4-11
Overvoltage category
EN 61010-1	II (≤ 5000 m)
EN 62477-1	III (≤ 2000 m)
EN 61558-2-16	II (≤ 4000 m)

Approvals

CSA	CAN/CSA-C22.2 No. 60950-1-07
	CSA-C22.2 No. 107.1-01
Shipbuilding approval	DNV GL, BV, LR, ABS
SIQ	BG (type approved)
	CB-Scheme (IEC 61010-1, IEC 61010-2-201, IEC 60950-1)
UL approvals	UL Listed UL 508
	UL/C-UL Recognized UL 60950-1
	UL ANSI/ISA-12.12.01 Class I, Division 2, Groups A, B, C, D T4 (Hazardous Location)

EMC data

Electromagnetic compatibility	Conformance with EMC Directive 2014/30/EU
Low Voltage Directive	Conformance with Low Voltage Directive 2014/35/EC
EMC requirements for noise emission	EN 61000-6-3
EMC requirements for noise emission		EN 61000-6-4
EMC requirements for noise immunity	EN 61000-6-1
EMC requirements for noise immunity		EN 61000-6-2
EMC requirements for power supply	IEC 61850-3 (G,H)
EMC requirements for power supply		EN 61000-6-5 (switching devices)
Conducted noise emission
Standards/regulations	EN 55016
Standards/regulations		EN 61000-6-3 (Class B)
Noise emission
Standards/regulations	Additional basic standard EN 61000-6-5 (immunity in switching devices), IEC/EN 61850-3 (power supply)
Noise emission
Standards/regulations	EN 55016
Standards/regulations		EN 61000-6-3 (Class B)
DNV GL conducted noise emissions
DNV	Class A
Additional text	Area power distribution
DNV GL noise radiation
DNV	Class B
Additional text	Bridge and deck area
Harmonic currents
Standards/regulations	EN 61000-3-2
Standards/regulations		EN 61000-3-2 (Class A)
Frequency range	0 kHz ... 2 kHz
Flicker
Standards/regulations	EN 61000-3-3
Standards/regulations		EN 61000-3-3
Frequency range	0 kHz ... 2 kHz
Electrostatic discharge
Standards/regulations	EN 61000-4-2
Electrostatic discharge
Contact discharge	8 kV (Test Level 4)
Discharge in air	15 kV (Test Level 4)
Comments	Criterion A
Electromagnetic HF field
Standards/regulations	EN 61000-4-3
Electromagnetic HF field
Frequency range	80 MHz ... 1 GHz
Test field strength	20 V/m (Test Level 3)
Frequency range	1 GHz ... 6 GHz
Test field strength	10 V/m (Test Level 3)
Comments	Criterion A
Fast transients (burst)
Standards/regulations	EN 61000-4-4
Fast transients (burst)
Input	4 kV (Test Level 4 - asymmetrical)
Output	4 kV (Test Level 4 - asymmetrical)
Signal	4 kV (Test Level 4 - asymmetrical)
Comments	Criterion A
Surge voltage load (surge)
Standards/regulations	EN 61000-4-5
Surge voltage load (surge)
Input	2 kV (Test Level 3 - symmetrical)
Input		6 kV (Test Level 4 - asymmetrical)
Output	1 kV (Test Level 3 - symmetrical)
Output		2 kV (Test Level 3 - asymmetrical)
Signal	4 kV (Test Level 2 - asymmetrical)
Comments	Criterion A
Conducted interference
Standards/regulations	EN 61000-4-6
Conducted interference
Input/output/signal	asymmetrical
Frequency range	0.15 MHz ... 80 MHz
Comments	Criterion A
Voltage	10 V (Test Level 3)
Power frequency magnetic field
Standards/regulations	EN 61000-4-8
Frequency	16.7 Hz
		50 Hz
		60 Hz
Test field strength	100 A/m
Additional text	60 s
Comments	Criterion A
Frequency	50 Hz
Frequency		60 Hz
Frequency range	50 Hz ... 60 Hz
Test field strength	1 kA/m
Additional text	3 s
Frequency	0 Hz
Test field strength	300 A/m
Additional text	DC, 60 s
Voltage dips
Standards/regulations	EN 61000-4-11
Voltage	400 V AC
Frequency	50 Hz
Voltage dip	70 %
Number of periods	0.5 / 1 / 25 periods
Additional text	Test Level 2
Comments	Criterion A: 0.5 / 1 period Criterion B: 25 periods
Voltage dip	40 %
Number of periods	5 / 10 / 50 periods
Additional text	Test Level 2
Comments	Criterion B
Voltage dip	0 %
Number of periods	0,5 / 1 / 5 / 50 / 250 periods
Additional text	Test Level 2
Comments	Criterion A: 0.5 / 1 period Criterion B: 5 / 50 / 250 periods
Pulse-shape magnetic field
Standards/regulations	EN 61000-4-9
Test field strength	1000 A/m
Comments	Criterion A
Attenuated sinusoidal oscillations (ring wave)
Standards/regulations	EN 61000-4-12
Input	2 kV (Test Level 4 - symmetrical)
Input		4 kV (Test Level 4 - asymmetrical)
Comments	Criterion A
Asymmetrical conducted disturbance variables
Standards/regulations	EN 61000-4-16
Test level 1	15 Hz 150 Hz (Test Level 4)
Voltage	30 V 3 V
Test level 2	150 Hz 1.5 kHz (Test Level 4)
Voltage	3 V
Test level 3	1.5 kHz 15 kHz (Test Level 4)
Voltage	3 V 30 V
Test level 4	15 kHz 150 kHz (Test Level 4)
Voltage	30 V
Test level 5	16.7 Hz 50 Hz 60 Hz 150 Hz 180 Hz (Test Level 4)
Voltage	30 V (10 s)
Test level 6	16.7 Hz 50 Hz 60 Hz (Test Level 4)
Voltage	300 V (1 s)
Comments	Criterion A
Attenuated oscillating wave
Standards/regulations	EN 61000-4-18
Input, output (test level 1)	100 kHz 1 MHz (Test Level 3 - symmetrical)
Voltage	1 kV
Input, output (test level 2)	10 MHz
Voltage	1 kV
Input, output (test level 3)	100 kHz 1 MHz (Test Level 3 - asymmetrical)
Voltage	2.5 kV
Signals (test level 1)	100 kHz 1 MHz (Test Level 3 - symmetrical)
Voltage	1 kV
Signals (test level 2)	100 kHz 1 MHz (Test Level 3 - asymmetrical)
Voltage	2.5 kV
Comments	Criterion A
Attenuated oscillating magnetic field
Standards/regulations	EN 61000-4-10
Test field strength	100 A/m
Test level 1	100 kHz
Test field strength	100 A/m
Test level 2	1 MHz
Comments	Criterion A
Criteria
Criterion A	Normal operating behavior within the specified limits.
Criterion B	Temporary impairment to operational behavior that is corrected by the device itself.
Criterion C	Temporary adverse effects on the operating behavior, which the device corrects automatically or which can be restored by actuating the operating elements.

Tuotenumero	2904623
Pakkausyksikkö	1 Kappaletta
Vähimmäistilausmäärä	1 Kappaletta
Tuoteavain	CMPI33
Tuotekoodi	CMPI33
GTIN	4055626356105
Paino kappaletta kohti (sis. pakkauksen)	2 811,6 g
Paino kappaletta kohti (ilman pakkausta)	2 422 g
Tullitariffinumero	85044095
Alkuperämaa	TH

ECLASS-13.0	27040701
ECLASS-15.0	27040701

EU RoHS
Täyttää RoHS-direktiivin vaatimukset	Kyllä
poikkeussäännökset siltä osin kuin ne ovat tiedossa	7(a), 7(c)-I
China RoHS
Environment friendly use period (EFUP)	EFUP-25 Löydät tuotekohtaisen Kiinan RoHS-ilmoitusluettelon kunkin tuotteen latausalueelta Valmistajan ilmoitus -kohdasta. EFUP-E-merkinnän sisältäville tuotteille ei tarvita Kiinan RoHS-ilmoitusluetteloa, eikä sitä tarvitse siksi laatia.
EU REACH SVHC
Huomautus REACH-kandidaattiaineesta (CAS-nro)	Lead (CAS-nro: 7439-92-1)
SCIP	95cb6219-1f6e-46d0-9ebd-ed4377268ff2
EF3.0 Ilmastonmuutos
CO2e kg	6,42 kg CO2e

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

QUINT4-PS/3AC/24DC/40 - Power supply

2904623

Tuotetiedot

ECLASS

ETIM

UNSPSC

cUL Recognized

UL Recognized

IECEE CB Scheme

EAC

LR

NK

IECEE CB Scheme

UL Listed

cUL Listed

ABS

EAC

DNV

BV

cCSAus

SEMI F47

cUL Listed

UL Listed

Yhteensopivat tuotteet

Edut

Usein kysytyt kysymykset

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

QUINT4-PS/3AC/24DC/40 - Power supply 2904623

Tuotetiedot

ECLASS

ETIM

UNSPSC

Yhteensopivat tuotteet

UWA 182/52 - Mounting adapter 2938235

UWA 130 - Mounting adapter 2901664

TWN4 MIFARE NFC USB ADAPTER - Programming adapter 2909681

FUSE 10,3X38 6A PV - Fuse 3061318

PLT-SEC-T3-3S-230-FM - Type 3 surge protection device 2905230

PLT-SEC-T3-24-FM-PT - Type 3 surge protection device 2907925

PLT-SEC-T3-24-FM-UT - Type 3 surge protection device 2907916

CBMC E4 24DC/1-4A NO - Electronic circuit breaker 2906031

CBMC E4 24DC/1-10A NO - Electronic circuit breaker 2906032

CBMC E4 24DC/1-4A+ IOL - Electronic circuit breaker 2910410

CBMC E4 24DC/1-10A IOL - Electronic circuit breaker 2910411

CBM E4 24DC/0.5-10A NO-R - Electronic circuit breaker 2905743

CBM E8 24DC/0.5-10A NO-R - Electronic circuit breaker 2905744

E/AL-NS 35 - End bracket 1201662

Edut

Usein kysytyt kysymykset

QUINT4-PS/3AC/24DC/40 - Power supply

2904623