Sisällöt, joita tarkastelet, on räätälöity kohteelle Suomi. Tarkastele sisältöjä kohteesta Yhdysvallat | Valitse toinen maa

PLC-RSC- 24DC/1/CB1-6 - Relay module

1328357

Combination of relay interface and electronic fuse protection on overall width: 6.2 mm, individual configuration of the nominal current (1 A ... 6 A), adjustable output characteristic, active signal output, easy system integration, with screw connection

Notes on operation	Repeated hard short circuits can reduce the melting integral of the integrated backup fuse.
Notes on operation	A suitable flyback diode must be used when switching inductive loads
Notes on operation	If the DIP switches are not covered by an adjacent module, the PLC-ATP partition plate must be used for ESD protection
Notes on operation	The device contains components that can be damaged or destroyed by electrostatic discharge. When handling the device, observe the necessary safety precautions against electrostatic discharge (ESD) according to EN 61340-5-1 and EN 61340-5-2.
Notes on operation	The PLC-ATP separating plate should be installed for safe isolation between adjacent modules
Notes on operation	Do not connect adjacent channels to SELV/ PELV and voltages dangerous to the touch.
Notes on operation	At least one functional insulation against adjacent modules is complied with in the support rail direction. If the application has higher requirements on the insulation (basic or reinforced insulation), then these must be realized through suitable measures (e. g., partition plates).
Notes on operation	Do not use to separate SELV / PELV circuits from other circuits, because safe isolation is not guaranteed.

Product type	Relay Module
Product family	PLC-INTERFACE
Application	with integrated electronic circuit breaker
Operating mode	100% operating factor
Insulation characteristics: Air clearances and creepage distances
Insulation	Functional insulation
Overvoltage category	I
Pollution degree	2

Maximum power dissipation for nominal condition	< 1.6 W
Fuse	electronic

Operating voltage (U_N)	24 V DC (U_In+ - U_A2)
Operating voltage range (DC)	19.2 V DC ... 30 V DC (U_In+ - U_A2)
Current consumption (In+)	12 mA
Tripping current (I_N)	1 A (adjustable)
	2 A (adjustable)
	3 A (adjustable)
	4 A (adjustable)
	5 A (adjustable)
	6 A (preset)
Measuring tolerance	± 15 %
Power dissipation	0.06 W (Without load, A1 low)
	0.4 W (Without load, A1 high)
	< 1.6 W (Normal operation)
Switching: Switching input A1
Nominal switch-on voltage	24 V (U_A1 - U_A2)
Switch-on voltage range	11 V ... 30 V (U_A1 - U_A2)
Switch-off voltage range	0 V ... 2 V (U_A1 - U_A2)
Current consumption (I_A1)	4 mA (24 V)
Switch-on time	36 ms
Switch-off time	10 ms
Switching frequency	≤ 2.5 Hz

Load circuit: Power MOSFET switching output (positive switching)
Voltage drop	0.16 V (6 A, U_In+ - U_out)
Short-circuit switching capacity	100 A DC
	300 A DC (<5 short circuits)
Required backup fuse	Only required if I_max of power supply unit > short-circuit switching capacity. Integrated failsafe element
Fail-safe element	15 A
Surge voltage protection	> 33 V
Max. capacitive load	12000 µF (Depending on the current setting and the short-circuit current available)
Shutdown time ()	≤ 15 ms (Short circuit ≥3 x I_N)
	0.1 s (Short circuit 2 ... <3 x I_N)
	1 s (Short circuit 1.5 ... <2 x I_N)
	4 s (Short circuit 1.1 ... <1.5 x I_N)
Undervoltage switch-off	≤ 17.8 V (active)
	≥ 19 V (inactive)
Overvoltage switch-off	≥ 30.5 V (active)
	≤ 29.5 V (inactive)
Waiting time	5 s (Between the pulses)
Number	5 (Start attempts in hiccup mode)
Signal: Feedback contact
Output voltage	U_In+ - 0.7 V (high level)
Current (Maximum current)	≤ 20 mA
State condition (Normal operation)	low
State condition (Error)	high (Fuse has blown)
State condition (Hiccup mode)	high (After all 5 start attempts have been completed)

Connection method	Screw connection
Stripping length	8 mm
Conductor cross section rigid	0.2 mm² ... 2.5 mm²
Conductor cross-section rigid (2 conductors with same cross section)	0.14 mm² ... 1.5 mm²
Conductor cross section flexible	0.2 mm² ... 2.5 mm²
	0.14 mm² ... 1.5 mm²
Conductor cross section flexible (2 conductors with same cross section)	0.5 mm² ... 1.5 mm² (TWIN ferrule with plastic sleeve)
Conductor cross section AWG	30 ... 12
Tightening torque	0.45 Nm ... 0.55 Nm (Usually these terminal blocks must be supported during conductor connection (held by one hand, supported on the housing))

Item dimensions
Width	6.2 mm
Height	80 mm
Depth	94 mm

Ambient conditions
Degree of protection	IP20
Degree of protection (Installation location)	≥ IP54
Ambient temperature (operation)	-25 °C ... 55 °C (Observe derating in the connected state)
Ambient temperature (storage/transport)	-40 °C ... 70 °C
Altitude	≤ 2000 m (Without derating)
	≤ 3000 m (With correction factor for ambient temperature (operation) x 0.88)
Permissible humidity (operation)	95 %

UL, USA/Canada
Identification	UL 2367
	UL 60947-1
	UL 60947-5-1
	CSA C22.2 No. 60947-1
	CSA C22.2 No. 60947-5-1
UL data
Operating mode	Indoor use

Electromagnetic compatibility (EMC)
Standards/regulations	EN 61000-6-2
	EN 61000-6-3
Air clearances and creepage distances
Standards/regulations	IEC 60664

Mounting type	DIN rail mounting
Assembly note	in rows with zero spacing
Mounting position	any

Tuotenumero	1328357
Pakkausyksikkö	1 Kappaletta
Vähimmäistilausmäärä	10 Kappaletta
Tuoteavain	DK622F
Tuotekoodi	DK622F
GTIN	4063151620974
Paino kappaletta kohti (sis. pakkauksen)	44,01 g
Paino kappaletta kohti (ilman pakkausta)	42,81 g
Tullitariffinumero	85364190
Alkuperämaa	DE

Yhteensopivat tuotteet

Lisätarvikkeet

ECLASS-13.0	27140401
ECLASS-15.0	27140401

EU RoHS
Täyttää RoHS-direktiivin vaatimukset	Kyllä
poikkeussäännökset siltä osin kuin ne ovat tiedossa	7(a), 7(c)-I
China RoHS
Environment friendly use period (EFUP)	EFUP-50 Löydät tuotekohtaisen Kiinan RoHS-ilmoitusluettelon kunkin tuotteen latausalueelta Valmistajan ilmoitus -kohdasta. EFUP-E-merkinnän sisältäville tuotteille ei tarvita Kiinan RoHS-ilmoitusluetteloa, eikä sitä tarvitse siksi laatia.
EU REACH SVHC
Huomautus REACH-kandidaattiaineesta (CAS-nro)	Lead (CAS-nro: 7439-92-1)

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

PLC-RSC- 24DC/1/CB1-6 - Relay module

1328357

Tuotetiedot

ECLASS

ETIM

UL Recognized

cULus Listed

Yhteensopivat tuotteet

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

PLC-RSC- 24DC/1/CB1-6 - Relay module 1328357

Tuotetiedot

ECLASS

ETIM

Yhteensopivat tuotteet

FBST 500-PLC RD - Continuous plug-in bridge 2966786

FBST 500-PLC BU - Continuous plug-in bridge 2966692

FBST 6-PLC RD - Single plug-in bridge 2966236

FBST 6-PLC BU - Single plug-in bridge 2966812

PLC-V8/FLK14/OUT - System connection 2295554

PLC-V8/D15S/OUT - System connection 2296058

PLC-ESK GY - Power terminal block 2966508

PLC-ATP BK - Separating plate 2966841

REL-MR- 24DC/21 - Single relay 2961105

PLC-RSC- 24DC/1/CB1-6 - Relay module

1328357