MINI MCR-2-U-UI-PT-C - Signal conditioner - 2902020

Detalii despre produs

Date tehnice

Notes

Utilization restriction
EMC note	EMC: class A product, see manufacturer's declaration in the download area

Product properties

Product type	Signal conditioner
Product family	MINI Analog Pro
No. of channels	1
Type	Signal conditioner
Configuration	DIP switches
Insulation characteristics: GB Standard
Overvoltage category	II
Pollution degree	2

Electrical properties

Electrical isolation	3-way isolation
Electrical isolation between input and output	yes
Limit frequency (3 dB)	30 Hz (via DIP switch)
Limit frequency (3 dB)		5 kHz (via DIP switch)
Protective circuit	Transient protection
Step response (10-90%)	< 8.5 ms (with 30 Hz filter)
Maximum temperature coefficient	0.01 %/K
Maximum transmission error	≤ 0.1 % (of final value)
Electrical isolation Input/output/power supply
Rated insulation voltage	300 V_rms
Test voltage	3 kV AC (50 Hz, 60 s)
Insulation	Reinforced insulation according to IEC/EN 61010-1
Supply
Nominal supply voltage	24 V DC
Supply voltage range	9.6 V DC ... 30 V DC (The DIN rail connector (ME 6,2 TBUS-2 1,5/5-ST-3,81 GN, item no. 2869728) can be used to bridge the supply voltage. It can be snapped onto a 35 mm DIN rail in accordance with EN 60715)
Typical current consumption	25 mA (Current output, at 24 V DC incl. load)
Typical current consumption		54 mA (Current output, at 12 V DC incl. load)
Power consumption (I output)	≤ 800 mW (at I_OUT = 20 mA, 9.6 V DC, 600 Ω load)

Input data

Signal: Voltage
Number of inputs	1
Configurable/programmable	Yes
Input signal	Voltage
Voltage input signal	-50 mV ... 50 mV (via DIP switch)
		0 mV ... 50 mV (via DIP switch)
		-60 mV ... 60 mV (via DIP switch)
		0 mV ... 60 mV (via DIP switch)
		-75 mV ... 75 mV (via DIP switch)
		0 mV ... 75 mV (via DIP switch)
		-80 mV ... 80 mV (via DIP switch)
		0 mV ... 80 mV (via DIP switch)
		-100 mV ... 100 mV (via DIP switch)
		0 mV ... 100 mV (via DIP switch)
		-120 mV ... 120 mV (via DIP switch)
		0 mV ... 120 mV (via DIP switch)
		-150 mV ... 150 mV (via DIP switch)
		0 mV ... 150 mV (via DIP switch)
		-200 mV ... 200 mV (via DIP switch)
		0 mV ... 200 mV (via DIP switch)
		-240 mV ... 240 mV (via DIP switch)
		0 mV ... 240 mV (via DIP switch)
		-300 mV ... 300 mV (via DIP switch)
		0 mV ... 300 mV (via DIP switch)
		-500 mV ... 500 mV (via DIP switch)
		0 mV ... 500 mV (via DIP switch)
		-600 mV ... 600 mV (via DIP switch)
		0 mV ... 600 mV (via DIP switch)
		-750 mV ... 750 mV (via DIP switch)
		0 mV ... 750 mV (via DIP switch)
		-800 mV ... 800 mV (via DIP switch)
		0 mV ... 800 mV (via DIP switch)
		-1 V ... 1 V (via DIP switch)
		0 V ... 1 V (via DIP switch)
		-1.2 V ... 1.2 V (via DIP switch)
		0 V ... 1.2 V (via DIP switch)
		-1.5 V ... 1.5 V (via DIP switch)
		0 V ... 1.5 V (via DIP switch)
		-2 V ... 2 V (via DIP switch)
		0 V ... 2 V (via DIP switch)
		-2.4 V ... 2.4 V (via DIP switch)
		0 V ... 2.4 V (via DIP switch)
		-3 V ... 3 V (via DIP switch)
		0 V ... 3 V (via DIP switch)
		-5 V ... 5 V (via DIP switch)
		0 V ... 5 V (via DIP switch)
		-6 V ... 6 V (via DIP switch)
		0 V ... 6 V (via DIP switch)
		-7.5 V ... 7.5 V (via DIP switch)
		0 V ... 7.5 V (via DIP switch)
		-8 V ... 8 V (via DIP switch)
		0 V ... 8 V (via DIP switch)
		-10 V ... 10 V (via DIP switch)
		0 V ... 10 V (via DIP switch)
		-12 V ... 12 V (via DIP switch)
		0 V ... 12 V (via DIP switch)
		-15 V ... 15 V (via DIP switch)
		0 V ... 15 V (via DIP switch)
		-20 V ... 20 V (via DIP switch)
		0 V ... 20 V (via DIP switch)
		-24 V ... 24 V (via DIP switch)
		0 V ... 24 V (via DIP switch)
		-30 V ... 30 V (via DIP switch)
		0 V ... 30 V (via DIP switch)
Max. voltage input signal	33 V
Input resistance of voltage input	> 10 kΩ

Output data

Signal: Voltage/current
Number of outputs	1
Configurable/programmable	Yes
Voltage output signal	0 V ... 5 V (via DIP switch)
		1 V ... 5 V (via DIP switch)
		-5 V ... 5 V (via DIP switch)
		0 V ... 10 V (via DIP switch)
		2 V ... 10 V (via DIP switch)
		-10 V ... 10 V (via DIP switch)
Non-load voltage	< 17 V
Current output signal	0 mA ... 20 mA (via DIP switch)
Current output signal		4 mA ... 20 mA (via DIP switch)
Max. current output signal	22 mA
Short-circuit current	< 32 mA
Load/output load voltage output	≥ 10 kΩ
Load/output load current output	≤ 600 Ω (at 20 mA)
Ripple	< 20 mV_PP (at 600 Ω)
Ripple		< 20 mV_PP (at 600 Ω)

Connection data

Connection method	Push-in connection
Stripping length	10 mm
Conductor cross section rigid	0.2 mm² ... 2.5 mm² (with ferrule)
	0.14 mm² ... 2.5 mm² (without ferrule)
Conductor cross section flexible	0.14 mm² ... 2.5 mm²
Conductor cross section AWG	24 ... 12 (flexible)

Ex data

Ex installation (EPL)	Gc
	Div. 2

Signaling

Status display	Green LED (supply voltage)

Dimensions

Width	6.2 mm
Height	109.81 mm
Depth	119.2 mm

Material specifications

Color	gray (RAL 7042)
Housing material	PBT

Environmental and real-life conditions

Ambient conditions
Degree of protection	IP20 (not assessed by UL)
Ambient temperature (operation)	-40 °C ... 70 °C
Ambient temperature (storage/transport)	-40 °C ... 85 °C
Permissible humidity (operation)	5 % ... 95 % (non-condensing)

Approvals

CE
Certificate	CE-compliant
ATEX
Identification	 II 3 G Ex ec ic IIC T4 Gc
Certificate	BVS 19 ATEX E 047 X
IECEx
Identification	Ex ec ic IIC T4 Gc
Certificate	IECEx BVS 19.0041X
CCC / China-Ex
Identification	Ex ec ic IIC T4 Gc
UL, USA/Canada
Identification	UL 508 Listed
		Class I, Div. 2, Groups A, B, C, D T6
		Class I, Zone 2, Group IIC T6
Shipbuilding approval
Certificate	DNV GL TAA00002UA
EAC Ex
Identification	 2Ex ec ic IIC T4 Gc
Certificate	BY/112 02.01 TP012 103.01 00079
Shipbuilding data
Temperature	B
Humidity	B
Vibration	A
EMC	A
Enclosure	Required protection according to the Rules shall be provided upon installation on board

EMC data

Electromagnetic compatibility	Conformance with EMC directive
Noise immunity	EN 61000-6-2
Note	When being exposed to interference, there may be minimal deviations.
Noise emission
Standards/regulations	EN 61000-6-4
Electrostatic discharge
Standards/regulations	EN 61000-4-2
Electrostatic discharge
Comments	Safety measures must be taken to prevent electrostatic discharge.
Electromagnetic HF field
Designation	Electromagnetic RF field
Standards/regulations	EN 61000-4-3
Fast transients (burst)
Designation	Fast transients (burst)
Standards/regulations	EN 61000-4-4
Surge current load (surge)
Standards/regulations	EN 61000-4-5
Conducted interference
Designation	Conducted interferences
Standards/regulations	EN 61000-4-6

Standards and regulations

Electrical isolation	3-way isolation
GB Standard
Standards/regulations	GB/T 3836.1
	GB/T 3836.3
	GB/T 3836.4

Mounting

Mounting type	DIN rail mounting
Assembly note	The DIN rail connector can be used for bridging the supply voltage. It can be snapped onto a 35 mm EN 60715 DIN rail.
Mounting position	any

Date comerciale

Număr articol	2902020
Unitate de ambalare	1 Bucată
Cantitate minimă pentru comandă	1 Bucată
Indicație	Produs la comandă (nereturnabil)
Cod produs	DK1121
Pagina de catalog	Pagina 74 (C-5-2019)
Greutate pe bucată (inclusiv ambalajul)	118,3 g
Greutate pe bucată (fără ambalaj)	120,8 g
Cod tarifar vamal	85437090
Țara de origine	DE

Clasificări

Aprobări

Environmental product compliance

EU RoHS
Îndeplineşte cerinţele conform directivei RoHS	Da
reglementări excepţionale, dacă sunt cunoscute	7(a), 7(c)-I
China RoHS
Environment friendly use period (EFUP)	EFUP-50 Un tabel de declarații China RoHS legat de articol poate fi găsit în zona de descărcare a articolului respectiv la „Declarația producătorului”. Nu se emite și nu este necesar niciun tabel de declarații China RoHS pentru toate articolele EFUP-E.
EU REACH SVHC
Trimitere la substanţa candidată REACH (nr. CAS)	Lead (nr. CAS: 7439-92-1)
Trimitere la substanţa candidată REACH (nr. CAS)		2,2',6,6'-tetrabromo-4,4'-isopropylidenediphenol (nr. CAS: 79-94-7)
SCIP	40e18d83-143e-494c-a5d2-1ae57a1f2027

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

MINI MCR-2-U-UI-PT-C - Signal conditioner

2902020

Detalii despre produs

ECLASS

ETIM

UNSPSC

DNV GL

UL Listed

CCC

cUL Listed

IECEx

cUL Listed

UL Listed

ATEX

EAC Ex

Produse compatibile

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

MINI MCR-2-U-UI-PT-C - Signal conditioner 2902020

Detalii despre produs

ECLASS

ETIM

UNSPSC

Produse compatibile

ME 6,2 TBUS-2 1,5/5-ST-3,81 GY - DIN rail bus connector 2695439

ME 6,2 TBUS-2 1,5/5-ST-3,81 GN - DIN rail bus connector 2869728

TC-D37SUB-AIO16-MP-PS-UNI - Module carrier 2906640

TC-D37SUB-ADIO16-MP-P-UNI - Module carrier 2906639

MINI MCR-2-V8-FLK 16 - System adapter 2901993

MINI MCR-2-V8-MOD-RTU - Communication module 2905634

MINI MCR-2-V8-MOD-TCP - Communication module 2905635

MINI MCR-2-V8-PB-DP - Communication module 2905636

MINI MCR-2-V8-PN - Communication module 2905637

FASTCON PRO-SET - Connector set 2906227

FASTCON PRO-SET-PT - Connector set 2906228

UCT-EM (30X5) - Marker for end clamp 0801505

UCT-EM (30X5) CUS - Marker for end clamp 0801589

SK 5,0 WH:REEL - Marker strip 0805221

UC-EMLP (15X5) - Plastic label 0819301

UC-EMLP (15X5) YE - Plastic label 0822615

UC-EMLP (15X5) CUS - Plastic label 0824550

UC-EMLP (15X5) YE CUS - Plastic label 0824551

UC-EMLP (15X5) SR - Plastic label 0828095

UC-EMLP (15X5) SR CUS - Plastic label 0828099

US-EMLP (15X5) - Plastic label 0828790

US-EMLP (15X5) YE - Plastic label 0828873

US-EMLP (15X5) SR - Plastic label 0828874

US-EMLP (15X5) CUS - Plastic label 0830076

US-EMLP (15X5) YE CUS - Plastic label 0830077

US-EMLP (15X5) SR CUS - Plastic label 0830078

UCT-EM (30X5) YE - Marker for end clamp 0830340

UCT-EM (30X5) YE CUS - Marker for end clamp 0830348

MINI MCR-2-PTB - Power terminal block 2902066

MINI MCR-2-PTB-PT - Power terminal block 2902067

QUINT4-SYS-PS/1AC/24DC/2.5/SC - Power supply 2904614

MINI MCR-2-FM-RC - Monitoring block 2904504

MINI MCR-2-FM-RC-PT - Monitoring block 2904508

SZS 0,6X3,5 - Screwdriver 1205053

MINI MCR-2-U-UI-PT-C - Signal conditioner

2902020