A safe redundant system is the result of the parallel connection of two power supply units which are decoupled from one another. To further increase system availability, QUINT DIODE provides the solution: decoupling with diode.
QUINT4-DIODE/12-24DC/2X20/1X40
-
Redundancy module
2907719
DIN rail diode module 12-24 V DC/2x20 A or 1x40 A. Uniform redundancy up to the consumer.
Tuotetiedot
| DC operation | |
| Nominal input voltage range | 12 V DC ... 24 V DC |
| Input voltage range | 10 V DC ... 30 V DC |
| Voltage type of supply voltage | DC |
| Reverse polarity protection | yes, < 60 V |
| Nominal input current (IN) | 1x 40 A (-40 °C ... 60 °C) |
| Maximum current Imax | 2x 30 A (-40 °C ... 40 °C) |
| 1x 60 A (-40 °C ... 40 °C) | |
| Input current IStatic | 2x 25 A (40 °C) |
| Input current IDynamic | 2x 30 A (5 s) |
| Input current ISFB | 2x 120 A (15 ms) |
| Nominal input current (IN) | 2x 20 A (-25 °C ... 60 °C) |
| 1x 40 A (-25 °C ... 60 °C) | |
| Maximum current Imax | 2x 30 A (-25 °C ... 40 °C) |
| 1x 60 A (-25 °C ... 40 °C) | |
| Transient surge protection | Varistor |
| Voltage drop, input/output | 0.5 V |
| Efficiency | > 97 % |
| Nominal output voltage | UIn - 0,5 V |
| Nominal output current (IN) | 40 A (Increasing power) |
| 20 A (Redundancy) | |
| Static Boost (IStat.Boost) | 45 A |
| Dynamic Boost (IDyn.Boost) | 60 A (5 s) |
| Selective Fuse Breaking (ISFB) | 120 A (15 ms) |
| Derating | 60 °C ... 70 °C (2.5 %/K) |
| Power loss nominal load max. | 10 W (IOUT = 20 A) |
| Connection in series | no |
| Input | |
| Connection method | Screw connection |
| Conductor cross-section, rigid min. | 0.5 mm² |
| Conductor cross-section, rigid max. | 16 mm² |
| Conductor cross-section flexible min. | 0.5 mm² |
| Conductor cross-section flexible max. | 16 mm² |
| Conductor cross-section AWG min. | 20 |
| Conductor cross-section AWG max. | 6 |
| Stripping length | 10 mm |
| Screw thread | M4 |
| Tightening torque, min | 1.2 Nm |
| Tightening torque max | 1.5 Nm |
| Output | |
| Connection method | Screw connection |
| Conductor cross-section, rigid min. | 0.5 mm² |
| Conductor cross-section, rigid max. | 16 mm² |
| Conductor cross-section flexible min. | 0.5 mm² |
| Conductor cross-section flexible max. | 16 mm² |
| Conductor cross-section AWG min. | 20 |
| Conductor cross-section AWG max. | 6 |
| Stripping length | 10 mm |
| Screw thread | M4 |
| Tightening torque, min | 1.2 Nm |
| Tightening torque max | 1.5 Nm |
| Insulation voltage input, output / housing | 1000 V |
| Product type | Redundancy module |
| Product family | QUINT DIODE |
| MTBF (IEC 61709, SN 29500) | 40000000 h (40 °C) |
| LED | no |
| Insulation characteristics | |
| Protection class | III |
| Degree of pollution | 2 |
| Dimensional drawing |
|
| Width | 50 mm |
| Height | 130 mm |
| Depth | 125 mm |
| Installation dimensions | |
| Installation distance right/left | 5 mm / 5 mm |
| Installation distance top/bottom | 50 mm / 50 mm |
| Mounting type | DIN rail mounting |
| Assembly note | alignable: PN ≥50%, 5 mm horizontally, 15 mm next to active components, 50 mm vertically alignable: PN <50%, 0 mm horizontally, 40 mm vertically top, 20 mm vertically bottom |
| Mounting position | horizontal DIN rail NS 35, EN 60715 |
| Flammability rating according to UL 94 (housing / terminal blocks) | V0 |
| Housing material | Metal |
| Housing material | Aluminum / stainless steel |
| Ambient conditions | |
| Degree of protection | IP20 |
| Ambient temperature (operation) | -40 °C ... 70 °C (> 60 °C Derating: 2,5 %/K) |
| Ambient temperature (storage/transport) | -40 °C ... 85 °C |
| Maximum altitude | ≤ 5000 m |
| Climatic class | 3K22 (in accordance with EN 60721-3-3) |
| Max. permissible relative humidity (operation) | ≤ 95 % (at 25 °C, non-condensing) |
| Shock | 18 ms, 30g, in each space direction (according to IEC 60068-2-27) |
| Vibration (operation) | < 15 Hz, amplitude ±2.5 mm (according to IEC 60068-2-6) |
| 15 Hz ... 150 Hz, 2.3g, 90 min. | |
| Temp code | T4 (-25 ... +70 °C; > 60 °C, Derating: 2,5 %/K) |
| Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installations | EN 50178/VDE 0160 (PELV) |
| Standard - Electrical safety | EN 60950-1/VDE 0805 (SELV) |
| Standard – Protection against shock currents, basic requirements for protective separation in electrical equipment | EN 50178 |
| Standard – Safety extra-low voltage | IEC 62368-1 (SELV) und EN 60204-1 (PELV) |
| Standard - Safe isolation | DIN VDE 0100-410 |
| Shipbuilding approval | DNV |
| UL approvals | UL/C-UL listed UL 508 |
| UL/C-UL Recognized UL 60950-1 | |
| UL ANSI/ISA-12.12.01 Class I, Division 2, Groups A, B, C, D T3C ... T4 (Hazardous Location) | |
| Conformity/Approvals | |
| ATEX | II 3 G Ex ec IIC T4 Gc |
| DEKRA 20ATEX0041 X | |
| IECEx | Ex ec IIC T4 Gc |
| IECEx DEK 20.0022X | |
| Electromagnetic compatibility | Conformance with EMC Directive 2014/30/EU |
| Low Voltage Directive | Conformance with Low Voltage Directive 2014/35/EC |
| EMC requirements for noise emission | EN 61000-6-3 |
| EN 61000-6-4 | |
| EMC requirements for noise immunity | EN 61000-6-1 |
| EN 61000-6-2 | |
| Surge voltage load (surge) | |
| Standards/regulations | EN 61000-4-5 |
| Surge voltage load (surge) | |
| Input | 2 kV (level 3 - asymmetrical: conductor to ground) |
| 1 kV (Level 2 - symmetrical: Conductor to conductor) | |
| Output | 2 kV (level 3 - asymmetrical: conductor to ground) |
| 1 kV (Level 2 - symmetrical: Conductor to conductor) | |
| Comments | Criterion A |
| Surge current load (surge) | |
| Standards/regulations | EN 61000-4-5 |
| Surge current load (surge) | |
| Input | 2 kV (level 3 - asymmetrical: conductor to ground) |
| 1 kV (Level 2 - symmetrical: Conductor to conductor) | |
| Output | 2 kV (level 3 - asymmetrical: conductor to ground) |
| 1 kV (Level 2 - symmetrical: Conductor to conductor) | |
| Comments | Criterion B |
| Emitted interference | |
| Standards/regulations | EN 61000-6-3 |
| Radio interference voltage in acc. with EN 55011 | EN 55011 (EN 55022) Class B, area of application: Industry and residential |
| Emitted radio interference in acc. with EN 55011 | EN 55011 (EN 55022) Class B, area of application: Industry and residential |
UL Recognized
Hyväksyntätunnus: E211944UL Listed
Hyväksyntätunnus: E123528cUL Listed
Hyväksyntätunnus: E123528DNV
Hyväksyntätunnus: TAA000011FNK
Hyväksyntätunnus: TA25015M| Nimellisjännite UN | Nimellisvirta IN | Poikkipinta AWG | Poikkipinta mm2 | |
|---|---|---|---|---|
| keine | ||||
| 500 V | 63 A | - 10 | ||
ATEX
Hyväksyntätunnus: DEKRA 20ATEX0041 XEAC Ex
Hyväksyntätunnus: KZ 7500525010102095IECEx
Hyväksyntätunnus: DEK 20.0022XcUL Listed
Hyväksyntätunnus: FILE E 199827UL Listed
Hyväksyntätunnus: E199827INMETRO
Hyväksyntätunnus: DNV 22.0238 XNEPSI-EX
Hyväksyntätunnus: GYJ20.1591XCCC
Hyväksyntätunnus: 2020322303003426
Edut
Flexible
Rugged design
Consistent redundancy up to the load
Usein kysytyt kysymykset
Is this module also suitable for series connection of power supplies?
No, the item can also be used in a series connection of power supplies. Correct wiring can protect the power supplies from critical voltages at the time of switch-on and switch-off, especially with capacitive loads.
NOTE:
Since "-" is not conne...
Näytä lisää
No, the item can also be used in a series connection of power supplies. Correct wiring can protect the power supplies from critical voltages at the time of switch-on and switch-off, especially with capacitive loads.
NOTE:
Since "-" is not connected for the protection of a series circuit, this device is not operated in accordance with its specification.
Does the item have integrated surge protection?
No. For integrated surge protection, we recommend the QUINT4-ORING/12-24DC/2X20/2X20 as an alternative.