QUINT-PS/2AC/1DC/24DC/20 - Power supply unit - 2320830

Input data

AC operation
Nominal input voltage range	2x 400 V AC ... 500 V AC
Input voltage range	2x 360 V AC ... 575 V AC
Input voltage range AC	2x 360 V AC ... 575 V AC
Voltage type of supply voltage	AC/DC
Inrush current	< 45 A (typical)
Inrush current integral (I²t)	< 1.5 A²s
AC frequency range	45 Hz ... 65 Hz
Frequency range DC	0 Hz
Mains buffering time	typ. 20 ms (400 V AC)
Current consumption	2.5 A (400 V AC)
Current consumption		2.1 A (500 V AC)
Nominal power consumption	888 VA
Protective circuit	Transient surge protection; Varistor
Input fuse	3.15 A (slow-blow, internal)
Recommended breaker for input protection	10 A ... 16 A (Characteristic B, C)
DC operation
Nominal input voltage range	600 V DC
Input voltage range	450 V DC ... 840 V DC
Input voltage range DC	450 V DC ... 840 V DC
Voltage type of supply voltage	AC/DC
Mains buffering time	< 28 ms (600 V DC)
Current consumption	0.9 A (600 V DC)
Protective circuit	Transient surge protection; Varistor
Permissible backup fuse	1000 V DC fuse 4 A 6 A

Output data

Efficiency	> 92 % (600 V DC)
Efficiency		> 90.5 % (400 V AC)
Nominal output voltage	24 V DC ±1 %
Setting range of the output voltage (U_Set)	18 V DC ... 29.5 V DC (U_IN ≥ 360 V AC / 480 V DC)
Setting range of the output voltage (U_Set)		18 V DC ... 26 V DC (< 480 V DC)
Nominal output current (I_N)	20 A (-25 °C ... 60 °C)
POWER BOOST (I_Boost)	26 A (-25 °C ... 40 °C permanent, U_OUT = 24 V DC )
Selective Fuse Breaking (I_SFB)	120 A (20 ms)
Magnetic circuit breaker tripping	C6 / B16
Derating	60 °C ... 70 °C (2.5 %/K)
Feedback voltage resistance	< 35 V DC
Protection against overvoltage at the output (OVP)	< 35 V DC
Max. capacitive load	unlimited
Active current limitation	Approx. 27 A
Control deviation	< 1 % (change in load, static 10 % ... 90 %)
		< 2 % (change in load, dynamic 10 % ... 90 %)
		< 0.1 % (change in input voltage ±10 %)
Residual ripple	< 50 mV_PP (with nominal values)
Output power	480 W
Peak switching voltages nominal load	< 50 mV_PP (20 MHz)
Maximum no-load power dissipation	11 W
Power loss nominal load max.	51 W
Rise time	< 2 ms (U_OUT (10 % ... 90 %))
Connection in parallel	yes, for redundancy and increased capacity
Connection in series	yes
Signal: DC OK floating
Output description	U_OUT>0.9 x U_N: Relays closed
Switching voltage range	≤ 30 V AC/DC
Maximum inrush current	≤ 100 mA (short-circuit-proof)
Signal: POWER BOOST, active
Output description	I_OUT < I_N: High signal
Switching voltage range	18 V DC ... 24 V DC
Maximum inrush current	< 20 mA (short-circuit-proof)
Signal: DC_IN OK, active
Output description	U_IN>450 V DC: high signal
Switching voltage range	18 V DC ... 24 V DC
Maximum inrush current	< 20 mA (short-circuit-proof)

Connection data

Input
Connection method	Screw connection
Conductor cross section, rigid min.	0.2 mm²
Conductor cross section, rigid max.	6 mm²
Conductor cross section flexible min.	0.2 mm²
Conductor cross section flexible max.	4 mm²
Conductor cross section AWG min.	24
Conductor cross section AWG max.	10
Stripping length	8 mm
Screw thread	M3
Tightening torque, min	0.5 Nm
Tightening torque max	0.6 Nm
Output
Connection method	Screw connection
Conductor cross section, rigid min.	0.2 mm²
Conductor cross section, rigid max.	6 mm²
Conductor cross section flexible min.	0.2 mm²
Conductor cross section flexible max.	4 mm²
Conductor cross section AWG min.	12
Conductor cross section AWG max.	10
Stripping length	8 mm
Screw thread	M3
Tightening torque, min	0.5 Nm
Tightening torque max	0.6 Nm
Signal
Conductor cross section, rigid min.	0.2 mm²
Conductor cross section, rigid max.	6 mm²
Conductor cross section flexible min.	0.2 mm²
Conductor cross section flexible max.	4 mm²
Conductor cross section AWG min.	24
Conductor cross section AWG max.	10
Screw thread	M3
Tightening torque, min	0.5 Nm
Tightening torque max	0.6 Nm

Signaling

Types of signaling	LED
	Relay contact
Signal output: DC OK floating
Status display	"DC OK" LED green
Color	green
Signal output: POWER BOOST, active
Status display	"BOOST" LED yellow/I_OUT> I_N : LED on
Color	yellow
Note on status display	LED on
Signal output: DC_IN OK, active
Status display	LED "DC_INOK" green / U_IN> 450 V DC: LED on
Color	green
Note on status display	LED on

Electrical properties

Number of phases	2.00
Insulation voltage input/output	1.5 kV AC (type test)
	2 kV AC (routine test)
Insulation voltage output / PE	500 V DC (routine test)
Insulation voltage input / PE	4 kV AC (type test)
	1.5 kV AC (routine test)

Product properties

Product type	Power supply
Product family	QUINT POWER
MTBF (IEC 61709, SN 29500)	> 860000 h (40 °C)
Insulation characteristics
Protection class	I
Degree of pollution	2

Dimensions

Width	120 mm
Height	130 mm
Depth	125 mm
Installation dimensions
Installation distance right/left	5 mm / 5 mm
Installation distance top/bottom	50 mm / 50 mm

Mounting

Mounting type	DIN rail mounting
Assembly note	alignable: P_N ≥50%, 5 mm horizontally, 15 mm next to active components, 50 mm vertically alignable: P_N <50%, 0 mm horizontally, 40 mm vertically top, 20 mm vertically bottom
Mounting position	horizontal DIN rail NS 35, EN 60715
With protective coating	no

Material specifications

Housing material	Metal
Housing material	Steel sheet, zinc-plated
Type of housing	Steel sheet, zinc-plated

Environmental and real-life conditions

Ambient conditions
Degree of protection	IP20
Ambient temperature (operation)	-25 °C ... 70 °C (> 60 °C Derating: 2,5 %/K)
Ambient temperature (storage/transport)	-40 °C ... 85 °C
Maximum altitude	≤ 2000 m
Climatic class	3K3 (in acc. with EN 60721)
Max. permissible relative humidity (operation)	≤ 95 % (at 25 °C, non-condensing)
Shock	18 ms, 30g, in each space direction (according to IEC 60068-2-27)
Vibration (operation)	< 15 Hz, amplitude ±2.5 mm (according to IEC 60068-2-6)
	15 Hz ... 150 Hz, 2.3g, 90 min.

Standards and regulations

Rail applications	EN 50121-4
Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installations	EN 50178/VDE 0160 (PELV)
Standard - Electrical safety	EN 60950-1/VDE 0805 (SELV)
	EN 61558-2-17
Standard - Safe isolation	DIN VDE 0100-410
Standard - Safety of transformers	EN 61558-2-17

Approvals

UL approvals	UL/C-UL listed UL 508
	UL/C-UL Recognized UL 60950-1

EMC data

Tuotenumero	2320830
Pakkausyksikkö	1 Kappaletta
Vähimmäistilausmäärä	1 Kappaletta
Tuoteavain	CMPQ23
Tuotekoodi	CMPQ23
Luettelosivu	Sivu 245 (C-4-2019)
GTIN	4046356580915
Paino kappaletta kohti (sis. pakkauksen)	2 026,7 g
Paino kappaletta kohti (ilman pakkausta)	2 000 g
Tullitariffinumero	85044095
Alkuperämaa	CN

ECLASS-11.0	27040701
ECLASS-13.0	27040701

EU RoHS
Täyttää RoHS-direktiivin vaatimukset	Kyllä
poikkeussäännökset siltä osin kuin ne ovat tiedossa	7(a), 7(c)-I
China RoHS
Environment friendly use period (EFUP)	EFUP-25 Löydät tuotekohtaisen Kiinan RoHS-ilmoitusluettelon kunkin tuotteen latausalueelta Valmistajan ilmoitus -kohdasta. EFUP-E-merkinnän sisältäville tuotteille ei tarvita Kiinan RoHS-ilmoitusluetteloa, eikä sitä tarvitse siksi laatia.
EU REACH SVHC
Huomautus REACH-kandidaattiaineesta (CAS-nro)	Lead (CAS-nro: 7439-92-1)

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

QUINT-PS/2AC/1DC/24DC/20 - Power supply unit

2320830

Tuotetiedot

ECLASS

ETIM

UNSPSC

Yhteensopivat tuotteet

Edut