SB-8EP6D8A9L34S - Coupler connector

1314988

Tuotetiedot

Tekniset tiedot

Notes

Order information:	Crimp contacts, 6x Ø 0.6 mm, 4x Ø 1 mm, 5x Ø 3.6 mm, order separately
Safety note
Safety note	WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
		• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
		• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
		• The products are suitable for applications in plant, controller, and electrical device engineering.
		• When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
		• Assembled products may not be manipulated or improperly opened.
		• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
		• When using the product in direct connection with third-party manufacturers, the user is responsible.
		• For operating voltages > 50 V AC, conductive connector housings must be grounded
		• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
		• Observe the corresponding technical data. You will find information: o On the product o On the packing label o In the supplied documentation o Online at phoenixcontact.com/products under the product
		• Only use tools recommended by Phoenix Contact
		• The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product.
		• Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products
		• Operate the connector only when it is fully plugged in and interlocked.
		• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
		• Observe the minimum bending radius of the cable. Lay the cable without twisting it.
		• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).

Product properties

Product type	Circular connector (cable-side)

Connector

Insulating body
Data rate	100 Mbps
Coding	Coding 2
Connection method	Crimp connection
Contact switching type	Pin
Application	Hybrid
Number of positions	15
Connection profile	6+4+4+PE
Installation height	2000 m (4000 m at 300 V system voltage in accordance with DIN EN 606664-1)
Number (Power contacts)	5
Contact diameter (Power contacts)	3.6 mm
Litz wires Min. cross section (Power contacts)	2.5 mm²
Litz wires Max. cross section (Power contacts)	16 mm²
Rated current Contact (Power contacts)	70 A (for max. connection cross section)
Rated voltage Contact (Power contacts)	630 V AC (Overvoltage category III/3)
Rated voltage Contact (Power contacts)		850 V DC (Overvoltage category II/3)
Rated surge voltage	6 kV
Overvoltage category	III
Degree of pollution	3
Number (Data contacts)	6
Contact diameter (Data contacts)	0.8 mm
Litz wires Max. cross section (Data contacts)	0.5 mm²
Rated current Contact (Data contacts)	2 A (for max. connection cross section)
Rated voltage Contact (Data contacts)	50 V AC/DC (Contact 5 ... 10)
Rated surge voltage	1.5 kV
Overvoltage category	II, III
Degree of pollution	3
Number (Signal contacts)	4
Contact diameter (Signal contacts)	1 mm
Litz wires Max. cross section (Signal contacts)	1.5 mm²
Rated current Contact (Signal contacts)	8 A (for max. connection cross section)
Rated voltage Contact (Signal contacts)	500 V AC/DC (Contact 1 ... 4)
Rated surge voltage	6 kV
Overvoltage category	III
Degree of pollution	3
Housing
Type	Coupling housing
Thread type	M40
Design	straight long
Type of locking	for standard and SPEEDCON interlock
Pg screw connection	none
Housing material	Turned parts: copper zinc alloy (CuZn), die-cast parts: zinc (GD-Zn)
Material for screw connection	CuZn
Degree of protection (plugged in)	IP68/IP69K
Seal
External cable diameter	20.5 mm ... 26.5 mm
Seal material	FKM

Environmental and real-life conditions

Ambient conditions
Ambient temperature (operation)	-40 °C ... 115 °C

Kaupalliset tiedot

Tuotenumero	1314988
Pakkausyksikkö	1 Kappaletta
Vähimmäistilausmäärä	1 Kappaletta
Huomautus	Toimeksiantosidonnainen valmistus (ei palautusta)
Tuoteavain	ABRCEG
Tuotekoodi	ABRCEG
GTIN	4063151572297
Paino kappaletta kohti (sis. pakkauksen)	396,907 g
Paino kappaletta kohti (ilman pakkausta)	396,907 g
Tullitariffinumero	85366990
Alkuperämaa	DE

Luokitukset

Hyväksynnät

Approval Specification Data
	Nimellisjännite U_N	Nimellisvirta I_N	Poikkipinta AWG
keine
Power	600 V	24 A	6
Signal	500 V	4 A	1,5
Data	50 V	1 A	0,25

Approval Specification Data
	Nimellisjännite U_N	Nimellisvirta I_N	Poikkipinta AWG
keine
Power	600 V	32 A	6
Signal	500 V	4 A	1,5
Data	50 V	1 A	0,25

Environmental product compliance

Yhteensopivat tuotteet

Lisätarvikkeet

Edut

Transmission of signals, data, and power in just a single connector

Mechanical coding reliably prevents incorrect connections

Safe use in the field, thanks to high degree of protection

Consistent EMC protection for reliable connection solutions in the industrial environment

ECLASS-13.0	27440116
ECLASS-15.0	27440116

EU RoHS
Täyttää RoHS-direktiivin vaatimukset	Kyllä
poikkeussäännökset siltä osin kuin ne ovat tiedossa	6(b)
China RoHS
Environment friendly use period (EFUP)	EFUP-50 Löydät tuotekohtaisen Kiinan RoHS-ilmoitusluettelon kunkin tuotteen latausalueelta Valmistajan ilmoitus -kohdasta. EFUP-E-merkinnän sisältäville tuotteille ei tarvita Kiinan RoHS-ilmoitusluetteloa, eikä sitä tarvitse siksi laatia.
EU REACH SVHC
Huomautus REACH-kandidaattiaineesta (CAS-nro)	Lead (CAS-nro: 7439-92-1)
SCIP	1562158a-9a14-46ad-aacb-597ace4c6eae

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

SB-8EP6D8A9L34S - Coupler connector

1314988

Tuotetiedot

ECLASS

ETIM

cUL Recognized

UL Recognized

Yhteensopivat tuotteet

Edut

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

SB-8EP6D8A9L34S - Coupler connector 1314988

Tuotetiedot

ECLASS

ETIM

Yhteensopivat tuotteet

SM-Z0003 - Square mounting flange with O-ring 1607935

SM-Z0004 - Square mounting flange 1607937

PROT-M40-PW-OT-IP20 - Plastic protective cap 1577212

SB-10KP001 - Crimp contact 1623607

SB-10KP002 - Crimp contact 1623611

SB-10KP003 - Crimp contact 1623612

SB-10KP004 - Crimp contact 1623613

SB-36KP002 - Crimp contact 1623383

SB-36KP003 - Crimp contact 1623384

SB-36KP004 - Crimp contact 1623385

SB-36KP005 - Crimp contact 1623386

ST-10KP010 - Crimp contact 1618255

ST-10KP035 - Crimp contact 1618458

SF-08KP010 - Crimp contact 1621574

SF-08KP020 - Crimp contact 1621575

SF-06KP010 - Crimp contact 1007186

SM-Z0025 - Color coding 1620558

SM-Z0026 - Color coding 1620559

SM-Z0027 - Color coding 1620560

Edut

SB-8EP6D8A9L34S - Coupler connector

1314988