M23-1RS1N8A8003 - Cable connector

1629198

Order information:	Order crimp contacts 16 x Ø 1 mm, 3 x Ø 1.5 mm separately
Safety note
Safety note	WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
	• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
	• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
	• The products are suitable for applications in plant, controller, and electrical device engineering.
	• When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
	• Assembled products may not be manipulated or improperly opened.
	• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
	• When using the product in direct connection with third-party manufacturers, the user is responsible.
	• For operating voltages > 50 V AC, conductive connector housings must be grounded
	• Ensure that the protective or functional ground has been properly connected.
	• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
	• Only use tools recommended by Phoenix Contact
	• The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product.
	• Operate the connector only when it is fully plugged in and interlocked.
	• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
	• Observe the minimum bending radius of the cable. Lay the cable without twisting it.
	• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).

Product type	Circular connector (cable-side)
Product family	M23 PRO

Connection 1
Head design	Socket
Insulating body
Coding	N
Material (Insulating body)	PA 6.6
Insertion/withdrawal cycles	100
Connection method	Crimp connection
Contact switching type	Socket
Application	Signal
Number of positions	19
Direction of rotation	Standard
Connection profile	16+2+PE
Installation height	2000 m
Number (Contact group 1)	3
Contact diameter (Contact group 1)	1.5 mm
Litz wires Min. cross section (Contact group 1)	0.08 mm²
Litz wires Max. cross section (Contact group 1)	1 mm²
Rated current Contact (Contact group 1)	10 A (for max. connection cross section)
Rated voltage Contact (Contact group 1)	150 V
Rated surge voltage	1.5 kV
Overvoltage category	II
Degree of pollution	3
Number (Contact group 2)	16
Contact diameter (Contact group 2)	1 mm
Litz wires Max. cross section (Contact group 2)	1 mm²
Rated current Contact (Contact group 2)	8 A (for max. connection cross section)
Rated voltage Contact (Contact group 2)	150 V
Overvoltage category	II
Degree of pollution	3
Housing
Type	Cable connector housing
Thread type	M23
Design	straight
Type of locking	Screw locking mechanism
Pg screw connection	none
Housing material	GD-Zn
Degree of protection (plugged in)	IP66/IP68 (2 m / 24 h) IP69K
Seal
External cable diameter	6 mm ... 10 mm
Seal material	FKM

Ambient conditions
Ambient temperature (operation)	-40 °C ... 105 °C (see to derating)
Permanent temperature	125 °C (DIN EN 60512-9-2 / 1000 h)

Tuotenumero	1629198
Pakkausyksikkö	1 Kappaletta
Vähimmäistilausmäärä	1 Kappaletta
Tuoteavain	ABRABA
Tuotekoodi	ABRABA
GTIN	4055626618319
Paino kappaletta kohti (sis. pakkauksen)	116,5 g
Paino kappaletta kohti (ilman pakkausta)	100,907 g
Tullitariffinumero	85366990
Alkuperämaa	DE

Yhteensopivat tuotteet

Lisätarvikkeet

Edut

Solutions with cross-manufacturer compatibility for standard and fast locking systems

Reliable under the harshest conditions: cable connectors with vibration brake

Modern, consistent design for highly convenient operation

Easy, cost-effective cable assembly: uniform shielding of M17 to M40

ECLASS-13.0	27440116
ECLASS-15.0	27440116

EU RoHS
Täyttää RoHS-direktiivin vaatimukset	Kyllä (Ei poikkeussäännöksiä)
China RoHS
Environment friendly use period (EFUP)	EFUP-E Ei raja-arvot ylittäviä vaarallisia aineita
EU REACH SVHC
Huomautus REACH-kandidaattiaineesta (CAS-nro)	Aineen pitoisuus ei ole yli 0,1 %.

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

M23-1RS1N8A8003 - Cable connector

1629198

Tuotetiedot

ECLASS

ETIM

UNSPSC

cUL Recognized

UL Recognized

Yhteensopivat tuotteet

Edut

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

M23-1RS1N8A8003 - Cable connector 1629198

Tuotetiedot

ECLASS

ETIM

UNSPSC

Yhteensopivat tuotteet

SF-Z0028 - Torque screwdriver 1607456

SF-Z0027 - Hook wrench 1607455

RF-Z0007 - Special wrench 1614347

RC-11S2000 - Crimp contact 1596772

RC-12S2000 - Crimp contact 1599600

RC-1KS2000 - Crimp contact 1602998

RC-15S2000 - Crimp contact 1623775

RC-15S2200 - Crimp contact 1627290

PROT-M23PRO-SG-IT-IP20 - Plastic protective cap 1055744

PROT-M23PRO-SG-IT-IP67 - Plastic protective cap 1055745

Edut

M23-1RS1N8A8003 - Cable connector

1629198