DEK-OE- 24DC/ 48DC/100 - Solid-state relay terminal block

2940207

Input solid-state relay terminal block, input: 24 V DC, output: 3 - 48 V DC/100 mA, terminal block width: 6.2 mm

Detalii despre produs

Note on application	Use of EB 80-DIK... bridges in the DEK terminal blocks: Absorption of humidity from the ambient air as well as an unfavorable tolerance between a larger number of DEK terminal blocks and the EB 80-DIK... bridge may cause (minor) expansion of the DEK housing. When the EB 80-DIK... bridges are used, therefore, it is recommended that these be disconnected after about 10 to 12 DEK terminal blocks and a wire bridge to the next DEK terminal block be inserted in their place.

Product family	DEK
Application	Output function
Operating mode	100% operating factor
Insulation characteristics: Standards/regulations
Insulation	Basic insulation
Overvoltage category	III
Pollution degree	2
Data management status
Date of last data management	15.09.2025

Maximum power dissipation for nominal condition	10 mW
Test voltage (Input/output)	2.5 kV AC (Input/output)

Nominal input voltage U_N	24 V DC
Input voltage range in reference to U_N	0.8 ... 1.2
Input voltage range	19.2 V DC ... 28.8 V DC
Switching threshold "0" signal in reference to U_N	≤ 0.4
Switching threshold "1" signal in reference to U_N	≥ 0.8
Typical input current at U_N	7 mA
Typical response time	20 µs
Typical turn-off time	200 µs
Operating voltage display	Green LED
Protective circuit	Reverse polarity protection
Transmission frequency	300 Hz

Contact switching type	1 N/O contact
Design of digital output	electronic
Output voltage range	3 V DC ... 48 V DC
Limiting continuous current	100 mA
Voltage drop at max. limiting continuous current	≤ 0.9 V
Output circuit	2-conductor floating, 3-conductor ground-referenced
Protective circuit	Reverse polarity protection; Polarity protection diode
	Freewheeling diode; Freewheeling diode
Output resistor	approx. 22 kΩ (for 3-conductor operation)

Connection method	Screw connection
Stripping length	8 mm
Screw thread	M3
Conductor cross-section rigid	0.2 mm² ... 2.5 mm²
Conductor cross-section flexible	0.2 mm² ... 2.5 mm²
Conductor cross-section AWG	24 ... 14
Tightening torque	0.4 Nm ... 0.5 Nm

Width	6.2 mm
Height	80 mm
Depth	56 mm

Color	green (RAL 6021)

Ambient conditions
Ambient temperature (operation)	-20 °C ... 60 °C
Ambient temperature (storage/transport)	-40 °C ... 70 °C

Standards/regulations
Standards/regulations	IEC 60947-5-1

Mounting type	DIN rail mounting
Assembly note	in rows with zero spacing
Mounting position	any

Date comerciale

Număr articol	2940207
Unitate de ambalare	10 Bucată
Cantitate minimă pentru comandă	1 Bucată
Cod produs	DK61A1
GTIN	4017918079901
Greutate pe bucată (inclusiv ambalajul)	20,83 g
Greutate pe bucată (fără ambalaj)	20,53 g
Cod tarifar vamal	85364190
Țara de origine	CN

Clasificări

Aprobări

Approval Specification Data
	Tensiune nominală U_N	Curent nominal I_N	Secțiune transversală AWG	Secțiune transversală mm²
keine
			30 - 14

Approval Specification Data
	Tensiune nominală U_N	Curent nominal I_N	Secțiune transversală AWG	Secțiune transversală mm²
keine
			30 - 14

Environmental product compliance

Produse compatibile

Accesorii

Avantajele dumneavoastră

Actuator version available

EB-DIK insertion bridges

Labeling and mounting with user-friendly modular terminal blocks

Wear-free switching of up to 24 V DC/10 A or 240 V AC/800 mA

Integrated output protective circuit

Integrated input circuit

Electrical isolation between input and output at up to 2.5 kVrms

Status indicator

Zero voltage switch at AC output

ECLASS-13.0	27371604
ECLASS-15.0	27371604

EU RoHS
Îndeplineşte cerinţele conform directivei RoHS	Da
reglementări excepţionale, dacă sunt cunoscute	7(a), 7(c)-I
China RoHS
Environment friendly use period (EFUP)	EFUP-50 Un tabel de declarații China RoHS legat de articol poate fi găsit în zona de descărcare a articolului respectiv la „Declarația producătorului”. Nu se emite și nu este necesar niciun tabel de declarații China RoHS pentru toate articolele EFUP-E.
EU REACH SVHC
Trimitere la substanţa candidată REACH (nr. CAS)	Hexahydromethylphthalic anhydride (nr. CAS: Nu corespunde)
Trimitere la substanţa candidată REACH (nr. CAS)		Lead (nr. CAS: 7439-92-1)
SCIP	f9c4e29b-a9d2-49b5-bea0-36cdcfae1456

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

DEK-OE- 24DC/ 48DC/100 - Solid-state relay terminal block

2940207

Detalii despre produs

ECLASS

ETIM

UNSPSC

cUL Recognized

UL Recognized

EAC

Produse compatibile

Avantajele dumneavoastră

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

DEK-OE- 24DC/ 48DC/100 - Solid-state relay terminal block 2940207

Detalii despre produs

ECLASS

ETIM

UNSPSC

Produse compatibile

EB 2- DIK RD - Insertion bridge 2716693

EB 3- DIK RD - Insertion bridge 2716745

EB 4- DIK RD - Insertion bridge 2716758

EB 5- DIK RD - Insertion bridge 2716761

EB 10- DIK RD - Insertion bridge 2716774

EB 80- DIK RD - Insertion bridge 2715953

EB 5- DIK BU - Insertion bridge 2716677

EB 10- DIK BU - Insertion bridge 2716680

EB 80- DIK BU - Insertion bridge 2715940

D-DEK 1,5 GN - Separating plate 2716949

ZB 6:UNBEDRUCKT - Zack marker strip 1051003

ZB 6,LGS:FORTL.ZAHLEN - Zack marker strip 1051016

ZB 6/WH-100:UNBEDRUCKT - Zack marker strip 5060935

DIKD 1,5 - Initiator/actuator terminal block 2715979

Avantajele dumneavoastră

DEK-OE- 24DC/ 48DC/100 - Solid-state relay terminal block

2940207