QUINT4-PS/3AC/24DC/20/... - Power supply - 2907873

Input data

Control input (configurable) Rem	Output power ON/OFF (SLEEP MODE)
Default	Output power ON (>40 kΩ/24 V DC/open bridge between Rem and SGnd)
AC operation
Network type	Star network
Nominal input voltage range	3x 400 V AC ... 500 V AC
Nominal input voltage range		2x 400 V AC ... 500 V AC
Input voltage range	3x 400 V AC ... 500 V AC -20 % ... +10 %
Input voltage range		2x 400 V AC ... 500 V AC -20 % ... +10 %
Typical national grid voltage	400 V AC
Typical national grid voltage		480 V AC
Voltage type of supply voltage	AC/DC
Inrush current	typ. 2 A (at 25 °C)
Inrush current integral (I²t)	< 0.1 A²s
Inrush current limitation	3 A (after 1 ms)
AC frequency range	50 Hz ... 60 Hz -10 % ... +10 %
Frequency range (f_N)	50 Hz ... 60 Hz -10 % ... +10 %
Mains buffering time	≥ 25 ms (3x 400 V AC)
Mains buffering time		≥ 25 ms (3x 480 V AC)
Current consumption	3x 0.99 A (400 V AC)
		3x 0.81 A (480 V AC)
		2x 1.62 A (400 V AC)
		2x 1.37 A (480 V AC)
		3x 0.8 A (500 V AC)
		2x 1.23 A (500 V AC)
Nominal power consumption	541 VA
Protective circuit	Transient surge protection; Varistor, gas-filled surge arrester
Switch-on time	< 1 s
Typical response time	300 ms (from SLEEP MODE)
Recommended breaker for input protection	3x 20 A (Characteristic B, C or comparable)
Recommended fuse for input protection	≥ 300 V AC
Discharge current to PE	< 3.5 mA
Discharge current to PE		1 mA (550 V AC, 60 Hz)
DC operation
Nominal input voltage range	± 260 V DC ... 300 V DC
Input voltage range	± 260 V DC ... 300 V DC -13 % ... +30 %
Voltage type of supply voltage	AC/DC
Current consumption	1.23 A (± 260 V DC)
Current consumption		1.06 A (±300 V DC)
Recommended breaker for input protection	1x 6 A (10 x 38 mm, 30 kA L/R = 2 ms)
Recommended fuse for input protection	≥ 1000 V DC

Output data

Efficiency	typ. 93.9 % (400 V AC)
Efficiency		typ. 93.8 % (480 V AC)
Nominal output voltage	24 V DC
Setting range of the output voltage (U_Set)	24 V DC ... 29.5 V DC (constant capacity)
Nominal output current (I_N)	20 A
Static Boost (I_Stat.Boost)	25 A
Dynamic Boost (I_Dyn.Boost)	30 A (5 s)
Selective Fuse Breaking (I_SFB)	120 A (15 ms)
Magnetic circuit breaker tripping	A1...A16 / B2...B13 / C1...C6 / Z1...Z16
Derating	> 60 °C (2.5 %/K)
Feedback voltage resistance	≤ 35 V DC
Protection against overvoltage at the output (OVP)	≤ 32 V DC
Control deviation	< 0.5 % (Static load change 10 % ... 90 %)
		< 3 % (Dynamic load change 10 % ... 90 %, (10 Hz))
		< 0.25 % (change in input voltage ±10 %)
Residual ripple	< 60 mV_PP (with nominal values)
Short-circuit-proof	yes
No-load proof	yes
Output power	480 W
		600 W
		720 W
Apparent power	686 VA (400 V, U_OUT = 24 V, I_OUT = stat. Boost)
Apparent power		698 VA (480 V, U_OUT = 24 V, I_OUT = stat. Boost)
Maximum no-load power dissipation	< 7 W (400 V AC)
Maximum no-load power dissipation		< 7 W (480 V AC)
Power loss nominal load max.	< 32 W (400 V AC)
Power loss nominal load max.		< 33 W (480 V AC)
Power dissipation SLEEP MODE	< 5 W (400 V AC)
Power dissipation SLEEP MODE		< 5 W (480 V AC)
Crest factor	typ. 1.78 (400 V AC)
Crest factor		typ. 2.1 (480 V AC)
Rise time	< 80 ms (U_Out = 10 % ... 90 %)
Connection in parallel	yes, for redundancy and increased capacity
Connection in series	yes
Signal
Signal ground SGnd	Reference potential for Out1, Out2, and Rem
Signal Out 1 (configurable)
Digital	24 V DC 20 mA
Analog	4 mA ... 20 mA
Default	24 V DC 20 mA U_OUT > 0.9 x U_Set
Signal Out 2 (configurable)
Digital	24 V DC 20 mA
Analog	4 mA ... 20 mA ±5 % (Load ≤400 Ω)
Default	24 V DC 20 mA 24 V DC for P_Out < P_N
Signal relay 13/14 (configurable)
Default	closed (U_out > 0.9 U_Set)

Connection data

Input
Connection method	Screw connection
Conductor cross section, rigid min.	0.2 mm²
Conductor cross section, rigid max.	6 mm²
Conductor cross section flexible min.	0.2 mm²
Conductor cross section flexible max.	4 mm²
Conductor cross section AWG min.	30
Conductor cross section AWG max.	10
Stripping length	8 mm
Tightening torque, min	0.5 Nm
Tightening torque max	0.6 Nm
Output
Connection method	Screw connection
Conductor cross section, rigid min.	0.2 mm²
Conductor cross section, rigid max.	6 mm²
Conductor cross section flexible min.	0.2 mm²
Conductor cross section flexible max.	4 mm²
Conductor cross section AWG min.	30
Conductor cross section AWG max.	10
Stripping length	8 mm
Tightening torque, min	0.5 Nm
Tightening torque max	0.6 Nm
Signal
Connection method	Push-in connection
Conductor cross section, rigid min.	0.2 mm²
Conductor cross section, rigid max.	1 mm²
Conductor cross section flexible min.	0.2 mm²
Conductor cross section flexible max.	1.5 mm²
Single conductor/flexible terminal point with ferrule with plastic sleeve, min.	0.2 mm²
Single conductor/flexible terminal point with ferrule with plastic sleeve, max.	0.75 mm²
Single conductor/flexible terminal point with ferrule without plastic sleeve, min.	0.2 mm²
Single conductor/flexible terminal point with ferrule without plastic sleeve, max.	1.5 mm²
Conductor cross section AWG min.	24
Conductor cross section AWG max.	16
Stripping length	8 mm

Signaling

Types of signaling	LED
	Floating signal contact
	Active signal output Out1 (digital, configurable)
	Active signal output Out2 (analog, configurable)
	Remote contact
	Signal ground SGnd
Signal output
P_Out	> 100 % (LED lights up yellow, output power > 480 W)
	> 75 % (LED lights up green, output power > 360 W)
	> 50 % (LED lights up green, output power > 240 W)
U_Out	> 0.9 x U_Set (LED lights up green)
	< 0.9 x U_Set (LED flashes green)

Electrical properties

Number of phases	3
Insulation voltage input/output	4 kV AC (type test)
	2.4 kV AC (routine test)
Insulation voltage output / PE	0.5 kV DC (type test)
	0.5 kV DC (routine test)
Insulation voltage input / PE	3.5 kV AC (type test)
	2.4 kV AC (routine test)
Switching frequency	90.00 kHz ... 110.00 kHz (Auxiliary converter stage)
	56.00 kHz ... 500.00 kHz (Main converter stage)
	25.00 kHz ... 500.00 kHz (PFC stage)

Product properties

Product type	Power supply
Product family	QUINT POWER
MTBF (IEC 61709, SN 29500)	> 985000 h (25 °C)
		> 638000 h (40 °C)
		> 311000 h (60 °C)
Environmental protection directive	RoHS Directive 2011/65/EU
		WEEE
		Reach
Insulation characteristics
Protection class	I
Degree of pollution	2
Life expectancy (electrolytic capacitors)
Current	10 A
Temperature	40 °C
Time	344000 h
Additional text	400 V AC
Life expectancy (electrolytic capacitors)
Current	10 A
Temperature	40 °C
Time	32000 h
Additional text	480 V AC
Life expectancy (electrolytic capacitors)
Current	20 A
Temperature	25 °C
Time	445000 h
Additional text	400 V AC
Life expectancy (electrolytic capacitors)
Current	20 A
Temperature	25 °C
Time	432000 h
Additional text	480 V AC
Life expectancy (electrolytic capacitors)
Current	20 A
Temperature	40 °C
Time	157000 h
Additional text	400 V AC
Life expectancy (electrolytic capacitors)
Current	20 A
Temperature	40 °C
Time	152000 h
Additional text	480 V AC

Dimensions

Width	70 mm
Height	130 mm
Depth	125 mm
Installation dimensions
Installation distance right/left	5 mm / 5 mm
Installation distance top/bottom	50 mm / 50 mm
Alternative assembly
Width	122 mm
Height	130 mm
Depth	73 mm

Mounting

Mounting type	DIN rail mounting
Assembly note	alignable: P_N ≥50%, 5 mm horizontally, 15 mm next to active components, 50 mm vertically alignable: P_N <50%, 0 mm horizontally, 40 mm vertically top, 20 mm vertically bottom
Mounting position	horizontal DIN rail NS 35, EN 60715
With protective coating	no

Material specifications

Flammability rating according to UL 94 (housing / terminal blocks)	V0
Housing material	Metal
Hood version	Stainless steel X6Cr17
Side element version	Aluminum

Environmental and real-life conditions

Ambient conditions
Degree of protection	IP20
Ambient temperature (operation)	-25 °C ... 70 °C (> 60 °C Derating: 2,5 %/K)
Ambient temperature (storage/transport)	-40 °C ... 85 °C
Ambient temperature (start-up type tested)	-40 °C
Maximum altitude	≤ 5000 m (> 2000 m, observe derating)
Climatic class	3K3 (in acc. with EN 60721)
Max. permissible relative humidity (operation)	≤ 95 % (at 25 °C, non-condensing)
Shock	18 ms, 30g, in each space direction (according to IEC 60068-2-27)
Vibration (operation)	5 Hz ... 100 Hz resonance search 2.3g, 90 min., resonance frequency 2.3g, 90 min. (according to DNV GL Class C)

Standards and regulations

Rail applications	EN 50121-3-2
		EN 50121-4
		EN 50121-5
		IEC 62236-3-2
		IEC 62236-4
		IEC 62236-5
Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installations	EN 50178/VDE 0160 (PELV)
Standard – Limitation of mains harmonic currents	EN 61000-3-2
Standard - Electrical safety	IEC 60950-1/VDE 0805 (SELV)
Standard – Safety extra-low voltage	IEC 60950-1 (SELV) and EN 60204-1 (PELV)
Standard - Safe isolation	DIN VDE 0100-410
Standard - safety for equipment for measurement, control, and laboratory use	IEC 61010-1
Standard - Safety of power supply units up to 1100 V (insulation distances)	DIN EN 61558-2-16
Standard - Safety of transformers	EN 61558-2-16 (air clearances and creepage distances only)
Standard - power supply devices for low voltage with DC output	EN 61204-3
Approval - requirement of the semiconductor industry with regard to mains voltage dips	SEMI F47-0706, EN 61000-4-11
Overvoltage category
EN 60950-1	II
EN 61010-1	II
EN 62477-1	III

Approvals

CSA	CAN/CSA-C22.2 No. 60950-1-07
	CSA-C22.2 No. 107.1-01
UL approvals	UL Listed UL 508
	UL/C-UL Recognized UL 60950-1

EMC data

Electromagnetic compatibility	Conformance with EMC Directive 2014/30/EU
Low Voltage Directive	Conformance with Low Voltage Directive 2014/35/EC
EMC requirements for noise emission	EN 61000-6-3
EMC requirements for noise emission		EN 61000-6-4
EMC requirements for noise immunity	EN 61000-6-1
EMC requirements for noise immunity		EN 61000-6-2
Conducted noise emission
Standards/regulations	EN 55016
Standards/regulations		EN 61000-6-3 (Class B)
Noise emission
Standards/regulations	Additional basic standard EN 61000-6-5 (immunity in switching devices), IEC/EN 61850-3 (power supply)
Noise emission
Standards/regulations	EN 55016
Standards/regulations		EN 61000-6-3 (Class B)
DNV GL conducted noise emissions
DNV	Class A
Additional text	Area power distribution
DNV GL noise radiation
DNV	Class B
Additional text	Bridge and deck area
Harmonic currents
Frequency range	0 kHz ... 2 kHz
Flicker
Frequency range	0 kHz ... 2 kHz
Electrostatic discharge
Standards/regulations	EN 61000-4-2
Electrostatic discharge
Contact discharge	8 kV (Test Level 4)
Discharge in air	15 kV (Test Level 4)
Comments	Criterion A
Electromagnetic HF field
Standards/regulations	EN 61000-4-3
Electromagnetic HF field
Frequency range	80 MHz ... 1 GHz
Test field strength	20 V/m (Test Level 3)
Frequency range	1 GHz ... 6 GHz
Test field strength	10 V/m (Test Level 3)
Frequency range	1 GHz ... 6 GHz
Test field strength	10 V/m (Test Level 3)
Comments	Criterion A
Fast transients (burst)
Standards/regulations	EN 61000-4-4
Fast transients (burst)
Input	4 kV (Test Level 4 - asymmetrical)
Output	4 kV (Test Level 3 - asymmetrical)
Signal	2 kV (Test Level 4 - asymmetrical)
Comments	Criterion A
Surge voltage load (surge)
Standards/regulations	EN 61000-4-5
Surge voltage load (surge)
Input	3 kV (Test Level 4 - symmetrical)
Input		6 kV (Test Level 4 - asymmetrical)
Output	1 kV (Test Level 3 - symmetrical)
Output		2 kV (Test Level 3 - asymmetrical)
Signal	1 kV (Test Level 2 - asymmetrical)
Comments	Criterion A
Conducted interference
Standards/regulations	EN 61000-4-6
Conducted interference
Input/output/signal	asymmetrical
Frequency range	0.15 MHz ... 80 MHz
Comments	Criterion A
Voltage	10 V (Test Level 3)
Power frequency magnetic field
Standards/regulations	EN 61000-4-8
Frequency	16.67 Hz
		50 Hz
		60 Hz
Test field strength	100 A/m
Additional text	60 s
Comments	Criterion A
Frequency	50 Hz
Frequency		60 Hz
Frequency range	50 Hz ... 60 Hz
Test field strength	1 kA/m
Additional text	3 s
Frequency	0 Hz
Test field strength	300 A/m
Additional text	DC, 60 s
Voltage dips
Standards/regulations	EN 61000-4-11
Voltage	400 V AC
Frequency	50 Hz
Voltage dip	70 %
Number of periods	0.5 / 1 / 25 periods
Additional text	Test Level 2
Comments	Criterion A: 0.5 / 1 period Criterion B: 25 periods
Voltage dip	40 %
Number of periods	5 / 10 / 50 periods
Additional text	Test Level 2
Comments	Criterion B
Voltage dip	0 %
Number of periods	0.5 / 1 / 5 / 50 periods
Additional text	Test Level 2
Comments	Criterion A: 0,5 / 1 period Criterion B: 5 / 50 periods
Pulse-shape magnetic field
Standards/regulations	EN 61000-4-9
Test field strength	1000 A/m
Comments	Criterion A
Attenuated sinusoidal oscillations (ring wave)
Standards/regulations	EN 61000-4-12
Input	2 kV (Test Level 4 - symmetrical)
Input		4 kV (Test Level 4 - asymmetrical)
Comments	Criterion A
Asymmetrical conducted disturbance variables
Standards/regulations	EN 61000-4-16
Test level 1	50 Hz 60 Hz (Test Level 3)
Voltage	10 V (Permanent)
Test level 2	0 Hz 16.67 Hz 50 Hz 60 Hz (Test Level 2)
Voltage	100 V (1 s)
Comments	Criterion A
Attenuated oscillating wave
Standards/regulations	EN 61000-4-18
Input/Output/Signal	0.5 kV (Test Level 2 - symmetrical)
Input/Output/Signal		1 kV (Test Level 2 - asymmetrical)
Comments	Criterion A
Criteria
Criterion A	Normal operating behavior within the specified limits.
Criterion B	Temporary impairment to operational behavior that is corrected by the device itself.
Criterion C	Temporary adverse effects on the operating behavior, which the device corrects automatically or which can be restored by actuating the operating elements.

Tuotenumero	2907873
Pakkausyksikkö	1 Kappaletta
Vähimmäistilausmäärä	1 Kappaletta
Huomautus	Toimeksiantosidonnainen valmistus (ei palautusta)
Tuoteavain	CMPI33
Tuotekoodi	CMPI33
Paino kappaletta kohti (sis. pakkauksen)	1 100 g
Paino kappaletta kohti (ilman pakkausta)	1 100 g
Tullitariffinumero	85044095
Alkuperämaa	TH

ECLASS-13.0	27040701
ECLASS-15.0	27040701

EU RoHS
Täyttää RoHS-direktiivin vaatimukset	Kyllä
poikkeussäännökset siltä osin kuin ne ovat tiedossa	7(a), 7(c)-I
China RoHS
Environment friendly use period (EFUP)	EFUP-25 Löydät tuotekohtaisen Kiinan RoHS-ilmoitusluettelon kunkin tuotteen latausalueelta Valmistajan ilmoitus -kohdasta. EFUP-E-merkinnän sisältäville tuotteille ei tarvita Kiinan RoHS-ilmoitusluetteloa, eikä sitä tarvitse siksi laatia.
EU REACH SVHC
Huomautus REACH-kandidaattiaineesta (CAS-nro)	Lead (CAS-nro: 7439-92-1)

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

QUINT4-PS/3AC/24DC/20/... - Power supply

2907873

Tuotetiedot

ECLASS

ETIM

UNSPSC

EAC

LR

BV

ABS

EAC

DNV

cCSAus

IECEE CB Scheme

IECEE CB Scheme

Type approved

cULus Recognized

cULus Listed

cULus Listed

Yhteensopivat tuotteet

Edut

Usein kysytyt kysymykset

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

QUINT4-PS/3AC/24DC/20/... - Power supply 2907873

Tuotetiedot

ECLASS

ETIM

UNSPSC

Yhteensopivat tuotteet

UWA 182/52 - Mounting adapter 2938235

UWA 130 - Mounting adapter 2901664

QUINT-PS-ADAPTERS7/1 - Mounting adapter 2938196

TWN4 MIFARE NFC USB ADAPTER - Programming adapter 2909681

FUSE 10,3X38 6A PV A - Fuse 3062778

PLT-SEC-T3-3S-230-FM - Type 3 surge protection device 2905230

PLT-SEC-T3-24-FM-UT - Type 3 surge protection device 2907916

Edut

Usein kysytyt kysymykset

QUINT4-PS/3AC/24DC/20/... - Power supply

2907873