VC-TFS 2 - Contact insert

1852846

Contact insert, Range of articles: VARIOCON, color: light grey, number of positions: 2, min. conductor cross-section: 0.25 mm², max. conductor cross-section: 4 mm², rated voltage: 400, rated current: 20 A, Connection method: Screw connection, Connectors may only be connected/disconnected when under no load.

Tuotetiedot

General	Connectors may only be connected/disconnected when under no load.
Safety note
Safety note	WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
	• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
	• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
	• The products are suitable for applications in plant, controller, and electrical device engineering.
	• When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
	• Assembled products may not be manipulated or improperly opened.
	• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
	• When using the product in direct connection with third-party manufacturers, the user is responsible.
	• For operating voltages > 50 V AC, conductive connector housings must be grounded
	• Ensure that the protective or functional ground has been properly connected.
	• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
	• Observe the corresponding technical data. You will find information: o On the product o On the packing label o In the supplied documentation o Online at phoenixcontact.com/products under the product
	• Only use tools recommended by Phoenix Contact
	• The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product.
	• Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products
	• Operate the connector only when it is fully plugged in.
	• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
	• Observe the minimum bending radius of the cable. Lay the cable without twisting it.
	• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).

Product family	VARIOCON
Series	VC-M
Number of positions	2
Number of module slots	1
Insulation characteristics
Degree of pollution	3

Rated voltage (II/2)	1000 V
Rated voltage (III/2)	400 V
Rated voltage (III/3)	400 V
	400 V
Nominal voltage ATD	400
Rated surge voltage	6 kV
Rated surge voltage (III/3)	6 kV
Rated surge voltage	6 kV
Rated current	20 A
	20 A
	20 A

Connection method	Screw connection
Tightening torque	0.5 ... 0.6 Nm

Dimensional drawing
Width	15 mm
Height	27.5 mm
Length	30.6 mm

Color	light grey
Color of the housing part	gray
Material Housing	Polyamide
Material Contact carrier	PA
Material Contact	SE-Cu
Flammability rating according to UL 94	V0
Insulating material group	I / CTI 600
Contact surface material	tin-plated

Single wire, cross section	0.25 mm² 4 mm² 24 10
Stripping length of the individual wire	10 mm

Mechanical data
Insertion/withdrawal cycles	≥ 100
Insertion force	9 N (per position)

Ambient conditions
Ambient temperature (operation)	-40 °C ... 100 °C

Kaupalliset tiedot

Tuotenumero	1852846
Pakkausyksikkö	50 Kappaletta
Vähimmäistilausmäärä	50 Kappaletta
Tuoteavain	ABLACA
Tuotekoodi	ABLACA
GTIN	4017918127145
Paino kappaletta kohti (sis. pakkauksen)	8,729 g
Paino kappaletta kohti (ilman pakkausta)	8,504 g
Tullitariffinumero	85366990
Alkuperämaa	PL

Luokitukset

Hyväksynnät

Approval Specification Data
	Nimellisjännite U_N	Nimellisvirta I_N	Poikkipinta AWG	Poikkipinta mm²
keine
	600 V	20 A	30 - 10

Approval Specification Data
	Nimellisjännite U_N	Nimellisvirta I_N	Poikkipinta AWG	Poikkipinta mm²
keine
	600 V	20 A	30 - 10

Approval Specification Data
	Nimellisjännite U_N	Nimellisvirta I_N	Poikkipinta AWG	Poikkipinta mm²
keine
	600 V	20 A

Approval Specification Data
	Nimellisjännite U_N	Nimellisvirta I_N	Poikkipinta AWG	Poikkipinta mm²
keine
	600 V	20 A

Environmental product compliance

Yhteensopivat tuotteet

Lisätarvikkeet

Edut

Proven COMBICON technology

Direct PCB connection

Can be keyed to prevent incorrect connection

ECLASS-13.0	27440192
ECLASS-15.0	27440192

EU RoHS
Täyttää RoHS-direktiivin vaatimukset	Kyllä (Ei poikkeussäännöksiä)
China RoHS
Environment friendly use period (EFUP)	EFUP-E Ei raja-arvot ylittäviä vaarallisia aineita
EU REACH SVHC
Huomautus REACH-kandidaattiaineesta (CAS-nro)	Aineen pitoisuus ei ole yli 0,1 %.
EF3.1 Ilmastonmuutos
CO2e kg	0,083 kg CO2e

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

VC-TFS 2 - Contact insert

1852846

Tuotetiedot

ECLASS

ETIM

UNSPSC

cUL Recognized

UL Recognized

UL Recognized

cUL Recognized

Yhteensopivat tuotteet

Edut

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

VC-TFS 2 - Contact insert 1852846

Tuotetiedot

ECLASS

ETIM

UNSPSC

Yhteensopivat tuotteet

CP-HCC 4 - Coding profile 1600027

Edut

VC-TFS 2 - Contact insert

1852846