UNO2-PS/1AC/24DC/480W - Power supply unit - 2910105

Докладно про виріб

Опис виробу

Технічні характеристики

Input data

AC operation
Supply system configuration	Star network (TN, TT, IT (PE))
Nominal input voltage range	100 V AC ... 240 V AC
Input voltage range	100 V AC ... 240 V AC -15 % ... +10 %
Derating	< 90 V AC (1 %/V)
Typical national grid voltage	120 V AC
Typical national grid voltage		230 V AC
Voltage type of supply voltage	AC
Inrush current	typ. 15 A (at 25 °C)
Inrush current integral (I²t)	< 1 A²s
Frequency range (f_N)	50 Hz ... 60 Hz ±10 %
Mains buffering time	typ. 17 ms (120 V AC)
Mains buffering time		typ. 18 ms (230 V AC)
Current consumption	5.4 A (100 V AC)
		4.4 A (120 V AC)
		2.3 A (230 V AC)
		2.2 A (240 V AC)
Protective circuit	Transient surge protection; Varistor, gas-filled surge arrester
Switch-on time	typ. 1 s
Device mains fuse	8 A internal (device protection), fast-blow
Recommended breaker for input protection	10 A ... 16 A (Characteristic B, C, D, K or comparable)
Discharge current to PE	< 3.5 mA

Output data

Efficiency	typ. 93 % (120 V AC)
Efficiency		typ. 94.6 % (230 V AC)
Nominal output voltage	24 V DC
Setting range of the output voltage (U_Set)	24 V DC ... 28 V DC (> 24 V DC, constant capacity restricted)
Nominal output current (I_N)	20 A
Short-circuit-proof	yes
No-load proof	yes
Derating	55 °C ... 70 °C
Crest factor	typ. 1.667 (120 V AC)
Crest factor		typ. 1.75 (230 V AC)
Output power (P_N)	480 W
Connection in parallel	yes, for redundancy
Connection in series	yes, for increased output voltage
Feedback voltage resistance	≤ 35 V DC
Protection against overvoltage at the output (OVP)	≤ 35 V DC
Residual ripple	typ. 70 mV_PP (with nominal values)
Control deviation	< 1 % (change in load, static 10 % ... 90 %)
		< 3 % (change in load, dynamic 10 % ... 90 %)
		< 0.1 % (change in input voltage ±10 %)
Rise time	< 1 s (U_Out = 10 % ... 90 %)
Minimum no-load power dissipation	< 2.9 W (120 V AC)
Maximum no-load power dissipation	< 3 W (230 V AC)
Minimum nominal load power dissipation	< 37 W (120 V AC)
Power loss nominal load max.	< 28 W (230 V AC)
Signal relay 13/14
Connection level	3.x
Connection labeling	3.1 (13), 3.2 (14)
Switch contact (floating)	OptoMOS
Switching voltage	max. 30 V AC/DC
Switching voltage		max. 60 V DC
Current carrying capacity	max. 50 mA
State condition	U_OUT > 0,9 x U_N (Contact closed)
State condition		U_OUT < 0,9 x U_N (Contact open)

Connection data

Input
Position	1.x
Identification	1.1 (), 1.2 (L), 1.3 (N)
Conductor connection
Connection method	Screw connection
rigid	0.2 mm² ... 6 mm²
flexible	0.2 mm² ... 4 mm²
flexible with ferrule without plastic sleeve	0.25 mm² ... 4 mm²
flexible with ferrule with plastic sleeve	0.25 mm² ... 4 mm²
rigid (AWG)	24 ... 10 (Cu)
AWG	24 ... 10 (Cu)
Stripping length	8 mm
Tightening torque	0.5 Nm ... 0.6 Nm
Tightening torque		4 lb_f-in. ... 5 lb_f-in.
Drive form screw head	Slotted L
Output
Position	2.x
Identification	2.1, 2.2 (+), 2.3, 2.4 (-)
Conductor connection
Connection method	Screw connection
rigid	0.2 mm² ... 6 mm²
flexible	0.2 mm² ... 4 mm²
flexible with ferrule without plastic sleeve	0.25 mm² ... 4 mm²
flexible with ferrule with plastic sleeve	0.25 mm² ... 4 mm²
rigid (AWG)	24 ... 10 (Cu)
AWG	24 ... 10 (Cu)
Stripping length	8 mm
Tightening torque	0.5 Nm ... 0.6 Nm
Tightening torque		4 lb_f-in. ... 5 lb_f-in.
Drive form screw head	Slotted L
Signal
Position	3.x
Identification	3.1 (13), 3.2 (14)
Conductor connection
Connection method	Screw connection
rigid	0.2 mm² ... 6 mm²
flexible	0.2 mm² ... 4 mm²
flexible with ferrule without plastic sleeve	0.25 mm² ... 4 mm²
flexible with ferrule with plastic sleeve	0.25 mm² ... 4 mm²
AWG	24 ... 10 (Cu)
Stripping length	8 mm
Tightening torque	0.5 Nm ... 0.6 Nm
Tightening torque		4 lb_f-in. ... 5 lb_f-in.
Drive form screw head	Slotted L

Signaling

LED signaling
Types of signaling	LED DC OK – signal state operation (U_N = 24 V DC, I_Out = I_N)
Function	Visual operating state display
Color	green
LED off	Supply voltage input AC not present (Off)
LED on (green), DC OK	U_OUT > 0,9 x U_N (On (green), DC OK)
LED on (flashing green) DC OK < 0.9 x UN	U_OUT < 0,9 x U_N (on (flashing green))

Electrical properties

Number of phases	1.00
Insulation voltage input/output	4 kV AC (type test)
	3 kV AC (routine test)
Insulation voltage input / PE	3.5 kV AC (type test)
	2.4 kV AC (routine test)

Product properties

Product type	Power supply
Product family	UNO POWER
MTBF (IEC 61709, SN 29500)	> 900000 h (25 °C)
	> 530000 h (40 °C)
	> 280000 h (55 °C)
Environmental protection directive	RoHS Directive 2011/65/EU
	WEEE
	Reach
Insulation characteristics
Protection class	I
Degree of pollution	2

Dimensions

Item dimensions
Width	59 mm
Height	130 mm
Depth	129 mm
	125 mm (Device depth (DIN rail mounting))
Installation dimensions
Installation distance right/left (active, passive)	0 mm / 0 mm
Installation distance top/bottom (active, passive)	30 mm / 30 mm

Mounting

Mounting type	DIN rail mounting
Assembly note	alignable: 0 mm horizontally, 30 mm vertically
Mounting position	horizontal DIN rail NS 35, EN 60715
With protective coating	no

Material specifications

Flammability rating according to UL 94	V0 (Housing, terminal blocks)
Housing material	Metal
Housing material	Aluminum (AlMg3) / sheet steel, zinc-plated
Hood version	Stainless steel
Side element version	Aluminum
Foot latch material	Sheet steel, zinc-plated

Environmental and real-life conditions

Ambient conditions
Degree of protection	IP20
Ambient temperature (operation)	-25 °C ... 70 °C (> 55 °C Derating: 2.5 %/K)
Ambient temperature (storage/transport)	-40 °C ... 85 °C
Ambient temperature (start-up type tested)	-40 °C
Maximum altitude	≤ 3000 m (> 2000 m, Derating: 10 %/1000 m)
Max. permissible relative humidity (operation)	≤ 95 % (at 25 °C, non-condensing)
Shock (operation)	18 ms, 30g, per spatial direction (IEC 60068-2-27)
Vibration (operation)	10 Hz ... 50 Hz, amplitude ±0.2 mm
	50 Hz ... 150 Hz, 2.3g, 90 min.
Temp code	T4 (-25°C ... +70°C; >55°C, derating: 2.5 %/K)

Standards and regulations

Overvoltage category
EN 61010-1	II (≤ 3000 m)
Overvoltage category
EN 62477-1	III (≤3000 m)
Safety of power supply units up to 1100 V (insulation distances)
Standard designation	Safety of power supply units up to 1100 V (insulation distances)
Standards/specifications	DIN EN 61558-2-16
Electrical safety
Standard designation	Electrical safety
Standards/specifications	IEC 61010-2-201 (SELV)
Safety for measurement, control, and laboratory equipment
Standard designation	Safety for equipment for measurement, control, and laboratory use
Standards/specifications	IEC 61010-1
Protective extra-low voltage
Standard designation	Protective extra-low voltage
Standards/specifications	IEC 61010-1 (SELV)
Standards/specifications		IEC 61010-2-201 (PELV)
Safe isolation
Standard designation	Safe isolation
Standards/specifications	IEC 61558-2-16
Standards/specifications		IEC 61010-2-201
Limitation of harmonic line currents
Standard designation	Limitation of harmonic line currents
Standards/specifications	EN 61000-3-2
Mains voltage dips
Standard designation	Requirement of the semiconductor industry with regard to mains voltage dips
Standards/specifications	SEMI F47 - 0706 (180 V AC)

Approvals

UL
Identification	UL/C-UL Listed UL 61010-1
UL
Identification	UL/C-UL Listed UL 61010-2-201
UL
Identification	UL/C-UL Listed ANSI/UL 121201 Class I, Division 2, Groups A, B, C, D (Hazardous Location)
SIQ
Identification	CB scheme (IEC 61010-1, IEC 61010-2-201)

EMC data

Electromagnetic compatibility	Conformance with EMC Directive 2014/30/EU
Low Voltage Directive	Conformance with Low Voltage Directive 2014/35/EC
Interference emission	Interference emission in accordance with EN 61000-6-3 (residential and commercial) and EN 61000-6-4 (industrial)
EMC requirements for noise immunity	EN 61000-6-2
Conducted noise emission
Standards/regulations	EN 55016
Standards/regulations		EN 61000-6-3 (Class B)
Noise emission
Standards/regulations	EN 55016
Standards/regulations		EN 61000-6-3 (Class B)
Harmonic currents
Standards/regulations	EN 61000-3-2
Standards/regulations		EN 61000-3-2 (Class A)
Frequency range	0 kHz ... 2 kHz
Flicker
Standards/regulations	EN 61000-3-3
Frequency range	0 kHz ... 2 kHz
Electrostatic discharge
Standards/regulations	EN 61000-4-2
Electrostatic discharge
Contact discharge	6 kV (Test Level 3)
Discharge in air	8 kV (Test Level 3)
Comments	Criterion A
Electromagnetic HF field
Standards/regulations	EN 61000-4-3
Electromagnetic HF field
Frequency range	80 MHz ... 1 GHz
Test field strength	10 V/m (Test Level 3)
Frequency range	1 GHz ... 6 GHz
Test field strength	10 V/m (Test Level 3)
Comments	Criterion A
Fast transients (burst)
Standards/regulations	EN 61000-4-4
Fast transients (burst)
Input	4 kV (Test Level 4 - asymmetrical)
Output	2 kV (Test Level 3 - asymmetrical)
Comments	Criterion A
Surge voltage load (surge)
Standards/regulations	EN 61000-4-5
Surge voltage load (surge)
Input	1 kV (Test Level 3 - symmetrical)
Input		2 kV (Test Level 3 - asymmetrical)
Output	0.5 kV (Test Level 2 - symmetrical)
Output		1 kV (Test Level 2 - asymmetrical)
Comments	Criterion B
Conducted interference
Standards/regulations	EN 61000-4-6
Conducted interference
Input/Output	asymmetrical
Frequency range	0.15 MHz ... 80 MHz
Comments	Criterion A
Voltage	10 V (Test Level 3)
Voltage dips
Standards/regulations	EN 61000-4-11
Voltage	230 V AC
Frequency	50 Hz
Voltage dip	70 %
Number of periods	25 / 30 periods
Comments	Criterion A
Voltage dip	40 %
Number of periods	12 periods
Additional text	Test Level 2
Comments	Criterion A
Voltage dip	0 %
Number of periods	1 period
Additional text	Test Level 2
Comments	Criterion B
Criteria
Criterion A	Normal operating behavior within the specified limits.
Criterion B	Temporary impairment to operational behavior that is corrected by the device itself.

Комерційні дані

Артикул	2910105
Пакувальна одиниця	1 Шт.
Мінімальний обсяг замовлення	1 Шт.
Код виробу	CMPV13
Сторінка каталогу	Сторінка268C-4-2019
GTIN	4055626456652
Маса штуки (з упаковкою)	1 252,4 g
Маса штуки (без упаковки)	1 084 g
Митний тарифний номер	85044095
Країна походження	TH

Класифікації

Відповідність стандартам

Environmental product compliance

EU RoHS
Відповідає вимогам Директиви RoHS	Так
винятки, якщо відомі	7(a), 7(c)-I
China RoHS
Environment friendly use period (EFUP)	EFUP-25 Пов’язану зі статтею таблицю декларації RoHS для Китаю можна знайти в області завантаження для відповідного товару в розділі «Декларація виробника». Таблиця декларації RoHS для Китаю не видається й не вимагається для всіх товарів з позначкою EFUP-E.
EU REACH SVHC
Інформація щодо речовини-кандидата за Регламентом REACH (№ CAS)	Lead (№ CAS: 7439-92-1)
		Lead (№ CAS: 7439-92-1)
SCIP	73c1ec9c-e95e-4452-8f4b-8bfe396d6c7e
EF3.0 Зміна клімату
CO2e кг	36,324 кг CO2e

ECLASS-11.0	27040701
ECLASS-13.0	27040701
ECLASS-12.0	27040701

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

UNO2-PS/1AC/24DC/480W - Power supply unit

2910105

Докладно про виріб

ECLASS

ETIM

UNSPSC

IECEE CB Scheme

UL Listed

cUL Listed

EAC

cUL Listed

UL Listed

cULus Listed

cULus Listed

Сумісна продукція

Переваги

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

UNO2-PS/1AC/24DC/480W - Power supply unit 2910105

Докладно про виріб

ECLASS

ETIM

UNSPSC

Сумісна продукція

QUINT4-DIODE/12-24DC/2X20/1X40 - Redundancy module 2907719

QUINT4-ORING/12-24DC/2X20/2X20 - Redundancy module 1088207

TRIO2-DIODE/12-24DC/2X20/1X40 - Redundancy module 2907379

PLT-SEC-T3-230-FM-UT - Type 3 surge protection device 2907919

CBMC E4 24DC/1-4A NO - Electronic circuit breaker 2906031

CBMC E4 24DC/1-10A NO - Electronic circuit breaker 2906032

CBMC E4 24DC/1-4A+ IOL - Electronic circuit breaker 2910410

CBMC E4 24DC/1-10A IOL - Electronic circuit breaker 2910411

CBM E4 24DC/0.5-10A NO-R - Electronic circuit breaker 2905743

CBM E8 24DC/0.5-10A NO-R - Electronic circuit breaker 2905744

Переваги

UNO2-PS/1AC/24DC/480W - Power supply unit

2910105