A considerably higher level of immunity to interference can be achieved in industrial applications by using V.24 (RS-232) isolator modules. The high-quality 3-way isolation results in an electrically isolated and interference-proof V.24 (RS-232) interface. This decoupling also protects the expensive terminal devices against damage.
PSM-ME-RS232/RS232-P
-
Interface converter
2744461
Interface converter, for the isolation of RS-232 (V.24) interfaces, 4 channels, rail-mountable
Докладно про виріб
| Note on application | |
| Note on application | Only for industrial use |
| Utilization restriction | |
| EMC note | EMC: class A product, see manufacturer's declaration in the download area |
| Utilization restriction | |
| CCCex note | Use in potentially explosive areas is not permitted in China. |
| Product type | Interface converter |
| Application | RS-232 |
| MTBF | 2263 Years (Telcordia standard, 25°C temperature, 21% operating cycle (5 days a week, 8 hours a day)) |
| 438 Years (Telcordia standard, 40°C temperature, 34.25% operating cycle (5 days a week, 12 hours a day)) |
| Electrical isolation | VCC // V.24 (RS-232) (A) // V.24 (RS-232) (B) |
| Maximum power dissipation for nominal condition | 0.96 W |
| Test voltage data interface/power supply | 2 kVrms (50 Hz, 1 min.) |
| 2 kV AC | |
| Test voltage data interfaces | 2 kV AC |
| Supply | |
| Supply voltage range | 19.2 V AC/DC ... 28.8 V AC/DC |
| Nominal supply voltage | 24 V AC/DC ±20 % |
| Typical current consumption | 40 mA (24 V DC) |
| Protective circuit | Surge protection; Suppressor diode |
| Supply | |
| Tightening torque | 0.56 Nm ... 0.79 Nm |
| Bit distortion | < 5 % |
| Bit delay | < 3 µs |
| Signal | Modbus |
| Transmission channels | 4 (2/2), RxD, TxD, RTS, CTS; full duplex |
| Data: V.24 (RS-232) interface in acc. with ITU-T V.28, EIA/TIA-232, DIN 66259-1 | |
| Serial transmission speed | 115.2 kbps |
| Connection method | D-SUB 9 plug |
| Pin assignment | DTE/DCE switchover via switch |
| Transmission length | 15 m (shielded twisted pair) |
| Single-wire/terminal point, flexible | 0.2 mm² ... 2.5 mm² |
| Max. AWG conductor cross section, flexible | 13 |
| Min. AWG conductor cross section, flexible | 24 |
| Protocols supported | transparent protocol |
| Data: V.24 (RS-232) interface in acc. with ITU-T V.28, EIA/TIA-232, DIN 66259-1 | |
| Connection method | Pluggable screw connection |
| Transmission length | 15 m (shielded twisted pair) |
| Single-wire/terminal point, flexible | 0.2 mm² ... 2.5 mm² |
| Max. AWG conductor cross section, flexible | 13 |
| Min. AWG conductor cross section, flexible | 24 |
| Dimensional drawing |
|
| Width | 22.5 mm |
| Height | 99 mm |
| Depth | 118.6 mm |
| Color (Housing) | green (RAL 6021) |
| Material (Housing) | PA |
| Ambient conditions | |
| Degree of protection | IP20 |
| Ambient temperature (operation) | 0 °C ... 55 °C |
| Ambient temperature (storage/transport) | -40 °C ... 85 °C |
| Altitude | ≤ 5000 m (For restrictions, see the manufacturer's declaration for altitude operation) |
| Permissible humidity (operation) | 10 % ... 95 % (non-condensing) |
| CE | |
| Certificate | CE-compliant |
| UL, USA/Canada | |
| Identification | 508 Recognized |
| Class I, Div. 2, Groups A, B, C, D | |
| Class I, Zone 2, AEx nA IIC T4 | |
| Class I, Zone 2, Ex nA IIC T4 Gc X | |
| Corrosive gas test | |
| Identification | ISA-S71.04-1985 G3 Harsh Group A |
| Shipbuilding | |
| Identification | DNV GL |
| Shipbuilding data | |
| Temperature | B |
| Humidity | A |
| Vibration | A |
| EMC | B |
| Enclosure | Required protection according to the Rules shall be provided upon installation on board |
| Electromagnetic compatibility | Conformance with EMC Directive 2014/30/EU |
| Noise immunity | EN 61000-6-2:2005 |
| Noise emission | |
| Standards/regulations | EN 61000-6-3 |
| Electrostatic discharge | |
| Standards/regulations | EN 61000-4-2 |
| Electrostatic discharge | |
| Contact discharge | ± 6 kV (Test Level 3) |
| Discharge in air | ± 8 kV (Test Level 3) |
| Comments | Criterion B |
| Electromagnetic HF field | |
| Standards/regulations | EN 61000-4-3 |
| Electromagnetic HF field | |
| Frequency range | Test Level 3 |
| Field intensity | 10 V/m |
| Comments | Criterion A |
| Fast transients (burst) | |
| Standards/regulations | EN 61000-4-4 |
| Fast transients (burst) | |
| Input | ± 4 kV (5 kHz) |
| Signal | ± 2 kV (5 kHz) |
| Comments | Criterion B |
| Surge current load (surge) | |
| Standards/regulations | EN 61000-4-5 |
| Surge current load (surge) | |
| Input | ± 0.5 kV (2 Ω) |
| Signal | ± 2 kV (12 Ω) |
| Comments | Criterion B |
| Conducted interference | |
| Standards/regulations | EN 61000-4-6 |
| Conducted interference | |
| Comments | Criterion A |
| Voltage | 10 V |
| Emitted interference | |
| Standards/regulations | EN 55011 |
| Comments | Class A, industrial applications |
| Criteria | |
| Criterion A | Normal operating behavior within the specified limits. |
| Criterion B | Temporary impairment to operational behavior that is corrected by the device itself. |
| Mounting type | DIN rail mounting |
UL Recognized
Ідентифікатор відповідності: E238705DNV GL
Ідентифікатор відповідності: TAA00001KRcUL Recognized
Ідентифікатор відповідності: FILE E 199827UL Recognized
Ідентифікатор відповідності: E199827cUL Listed
Ідентифікатор відповідності: E199827UL Listed
Ідентифікатор відповідності: E199827
Переваги
Mounting on standard EN DIN rails
High-quality 3-way isolation up to 2 kV (VCC // RS-232 // RS-232)
In the case of variable cable lengths, the RS-232 connection on the field side can be established conveniently using plug-in screw terminal blocks
Integrated surge protection with transient discharge to the DIN rail
Transmission of TxD/RxD data channels and RTS/CTS control lines
24 V DC or AC power supply suitable for the control cabinet
Active data transmission indicated by separate data indicators for the transmit and receive channels
Maximum transmission speed of 115.2 kbps
Shipbuilding approval in accordance with DNV GL