HC-Q02-I-AT-F - Contact insert

1496732

Contact insert, number of positions: 2+PE, size: D7, power contacts: 2, number of connections per position: 1, Socket, Axial screw connection, 400 V, 40 A, 1.5 mm² ... 10 mm², application: Power

Detalhes dos produtos

General	Connectors may be operated only when there is no load/voltage.
General	The axial screw connection must be established using a 2 mm Allen key (for stranded conductors only)

Assembly note	To ensure correct use, installation in housing with IP54 protection or better is required
	Note regarding axial connection technology: Only for stranded wires. The specified conductor cross-sections refer to the geometric cross section of the cable used. Cables with a geometric cross section which deviates significantly from the nominal cable cross section must be checked before use. The axial connection technology connection space is designed for fine strand cables according to VDE 0295 Class 5. Deviating cable structures (e.g., Class 6 cables) must be checked before use. Assembly instructions Before assembly, ensure that the tapered screw is fully loosened (chamber is open). Cables must not be twisted. The wires must be pushed into the contact chamber as far as they will go (until the insulation touches the contact). Hold the wires in position and tighten using an Allen key. The used wire end must be cut off before reconnection. The terminal screw must only be retightened once to prevent the litz wires from breaking. To prevent damage to the contact, the wire/cable must be mechanically held at an appropriate distance from the connection point (e.g., when used in a plate cut out). For notes on correct execution, see DIN VDE 0100-520:2003-06. Unused connections must be tightened with maximum torque.
Hexagonal socket	SW2,0

Product type	Contact insert with a fixed no. of positions
Series	HC-Q
Application	Power
Type	D7
Number of positions	2
Connection profile	2+PE
Number of connections per position	1
No. of power contacts	2
Contact material type	turned
Insulation characteristics
Overvoltage category	III
Degree of pollution	3

Mechanical characteristics
Contact diameter	4 mm

Connection technology
Connection technology	Axial screw connection
Number of connections per position	1
Connection in acc. with standard	IEC / EN
Conductor connection
Conductor cross section	1.5 mm² ... 10 mm² (The cross section specification refers to the geometric cross section of the cable used)
Tightening torque	0.5 Nm ... 0.8 Nm (Mounting screws for mounting in the HEAVYCON housing)
	0.5 Nm (1.5 mm²)
	0.8 Nm (2.5 mm² ... 4 mm²)
	1.5 Nm (6 mm² ... 10 mm²)
Stripping length of the individual wire	6 mm
Stripping length	5 mm ... 7 mm

Rated voltage (III/3)	400 V
Rated surge voltage	6 kV
Rated current	40 A

Mechanical data
Insertion/withdrawal cycles	≥ 500

Flammability rating according to UL 94	V0
Contact material	Copper alloy
Contact surface material	Ag
Contact carrier material	PC
Standards/regulations	PC

Ambient conditions
Ambient temperature (operation)	-40 °C ... 125 °C (including heating up of contacts)

Testing
Standards/regulations	PC: Fire protection in rail vehicles - requirement sets R22, R23, and R24 acc. to DIN EN 45545-2 (Risk level HL1 - HL3)

Dados comerciais

N.º de artigo	1496732
Pcs./Emb	1 Unidade
Quantidade mínima de pedido	1 Unidade
Chave comercial	AF7
Chave de produto	AF7ABJ
GTIN	4063151946531
Peso por unidade (inclusive embalagem)	20,5 g
Peso por unidade (excluindo embalagem)	22,22 g
Número do imposto alfandegário	85366990
País de origem	PL

Classificações

Certificações

Approval Specification Data
	Tensão nominal U_N	Corrente nominal I_N	Secção transversal American Wire Gauge
keine
Power	600 V	45 A	- 8
PE connection			- 10

Approval Specification Data
	Tensão nominal U_N	Corrente nominal I_N	Secção transversal American Wire Gauge
keine
Power	600 V	45 A	- 8
PE connection			- 10

Environmental product compliance

Produtos compatíveis

Acessórios

Vantagens

Shock and vibration-resistant in accordance with DIN EN 61373

Phoenix Contact S.A.

Sintra Business Park, Edifício n°1 Zona Industrial da Abrunheira, sala 0M, 2710-089 SINTRA

Fazer uma pergunta (+351) 21 911 2760 pt-info@phoenixcontact.com

ECLASS-13.0	27440205
ECLASS-15.0	27440205

EU RoHS
Cumpre os requisitos de substância segundo a Diretiva RoHS	Sim (Sem regras de exceção)
China RoHS
Environment friendly use period (EFUP)	EFUP-E Nenhuma substância perigosa acima dos valores-limite
EU REACH SVHC
Nota sobre as substâncias candidatas ao REACH (n.º CAS)	Nenhuma substância numa proporção superior a 0,1 % em massa

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

HC-Q02-I-AT-F - Contact insert

1496732

Detalhes dos produtos

ECLASS

ETIM

UNSPSC

UL Recognized

CSA

Produtos compatíveis

Vantagens

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

HC-Q02-I-AT-F - Contact insert 1496732

Detalhes dos produtos

ECLASS

ETIM

UNSPSC

Produtos compatíveis

HC-D 7-DS-IP65 - Sealing screw 1686229

HC-CP-D07-PL - Coding element 1095413

HC-Q02-I-AT-M - Contact insert 1496723

SF-BIT-HEX 2-89 S - Screw insert 1200300

TSD-M 3NM - Torque screwdriver 1212225

Vantagens

Pesquisado com frequência

HC-Q02-I-AT-F - Contact insert

1496732