MINI MCR-2-TC-UI - Thermocouple measuring transducer - 2902055

Detalhes dos produtos

Descrição do produto

Dados técnicos

Notes

Utilization restriction
EMC note	EMC: class A product, see manufacturer's declaration in the download area

Product properties

Product type	Temperature transmitter
Product family	MINI Analog Pro
Type	Signal conditioner
Configuration	DIP switches
	Software
	App
Insulation characteristics
Overvoltage category	II
Pollution degree	2

System properties

Functionality
Configuration	DIP switches
	Software
	App

Electrical properties

Electrical isolation	3-way isolation
Typical cold point errors	2 K (2 K + (0.2 K * ΔT))
Protective circuit	Transient protection
Step response (0–99%)	300 ms
Step response (0–99%)		570 ms
Maximum temperature coefficient	≤ 0.01 %/K
Transmission error thermocouples	0.1% * 600 K / set measuring range; 0.1% > 600 K (C, E, J, K, N, T, L, U, M Gost, L Gost)
		0.2 % * 600 K / set measuring range; 0.2 % > 600 K (B, R, S, A1, A2, A3)
		0.2 % * 600 K / set measuring range; 0.2 % > 600 K (E, J, K, N, T, L, U, M Gost, L Gost); Highspeed Mode
		0.4% * 600 K / set measuring range; 0.4% > 600 K (B, R, S, A1, A2, A3); Highspeed Mode
Electrical isolation Input/output/power supply
Rated insulation voltage	300 V_rms
Test voltage	3 kV AC (50 Hz, 60 s)
Insulation	Reinforced insulation according to IEC/EN 61010-1
Supply
Supply voltage range	9.6 V DC ... 30 V DC (The DIN rail connector (ME 6,2 TBUS-2 1,5/5-ST-3,81 GN, item no. 2869728) can be used to bridge the supply voltage. It can be snapped onto a 35 mm DIN rail in accordance with EN 60715)
Typical current consumption	32.7 mA (24 V DC)
Typical current consumption		66.8 mA (12 V DC)
Power consumption	≤ 850 mW (at I_OUT = 20 mA, 9.6 V DC, 600 Ω load)

Input data

Signal
Number of inputs	1
Measurement
Number of inputs	1
Configurable/programmable	Yes
Input voltage range	- 500 mV ... 500 mV (can be set via software)
Sensor types that can be used (TC)	B, C, E, J, K, N, R, S, T, L, U, A-1, A-2, A-3, M, L
Temperature measuring range	-250 °C ... 2500 °C (Range depends on sensor type, range can be set freely via software or in increments from -150°C to 1350°C via DIP switches)
Temperature measuring range	≥ 50 K
Voltage measuring range	3 mV
Sensor type:	500 °C ... 1820 °C
		-230 °C ... 1000 °C
		-210 °C ... 1200 °C
		-250 °C ... 1372 °C
		-200 °C ... 1300 °C
		-50 °C ... 1768 °C
		-50 °C ... 1768 °C
		-200 °C ... 400 °C
		-200 °C ... 900 °C
		-200 °C ... 600 °C
		0 °C ... 2500 °C
		0 °C ... 1800 °C
		0 °C ... 1800 °C
		-200 °C ... 100 °C
		-200 °C ... 800 °C

Output data

Signal: Voltage/current
Number of outputs	1
Configurable/programmable	Yes
Voltage output signal	0 V ... 5 V (via DIP switch)
		1 V ... 5 V (via DIP switch)
		0 V ... 10 V (via DIP switch)
		10 V ... 0 V (via DIP switch)
		0 V ... 10.5 V (can be set via software)
Max. voltage output signal	 12.3 V
Non-load voltage	< 17.5 V
Current output signal	0 mA ... 20 mA (via DIP switch)
		4 mA ... 20 mA (via DIP switch)
		20 mA ... 0 mA (via DIP switch)
		20 mA ... 4 mA (via DIP switch)
		0 mA ... 21 mA (can be set via software)
Max. current output signal	24.6 mA
Short-circuit current	< 31.5 mA
Load/output load voltage output	≥ 10 kΩ
Load/output load current output	≤ 600 Ω (20 mA)
Ripple	< 10 mV_rms
Ripple		< 10 mV_rms (600 Ω)
Resolution, outputs (voltage)	1 mV
Resolution, outputs (current)	2 µA

Connection data

Connection method	Screw connection
Stripping length	10 mm
Screw thread	M3
Conductor cross section rigid	0.2 mm² ... 1.5 mm² (with ferrule)
	0.14 mm² ... 2.5 mm² (without ferrule)
Conductor cross section flexible	0.14 mm² ... 2.5 mm²
Conductor cross section AWG	24 ... 12 (flexible)
Tightening torque	0.5 Nm ... 0.6 Nm

Ex data

Ex installation (EPL)	Gc
	Div. 2

Interfaces

Data: IFS interface
Connection method	Micro USB type B

Signaling

Status display	Green LED (supply voltage)
Error indication	Red LED

Dimensions

Width	6.2 mm
Height	109.81 mm
Depth	119.2 mm

Material specifications

Color	gray (RAL 7042)
Housing material	PBT
Fire protection for rail vehicles (DIN EN 45545-2) R22	HL 1 - HL 2
Fire protection for rail vehicles (DIN EN 45545-2) R23	HL 1 - HL 2
Fire protection for rail vehicles (DIN EN 45545-2) R24	HL 1 - HL 2

Environmental and real-life conditions

Ambient conditions
Degree of protection	IP20 (not assessed by UL)
Ambient temperature (operation)	-40 °C ... 70 °C
Ambient temperature (storage/transport)	-40 °C ... 85 °C
Altitude	≤ 2000 m
Permissible humidity (operation)	5 % ... 95 % (non-condensing)

Approvals

CE
Certificate	CE-compliant
ATEX
Identification	 II 3 G Ex ec IIC T4 Gc
Certificate	BVS 20 ATEX E 024 X
IECEx
Identification	Ex ec IIC T4 Gc
Certificate	IECEx BVS 20.0017X
UL, USA/Canada
Identification	UL 508 Listed
		Class I, Div. 2, Groups A, B, C, D T6
		Class I, Zone 2, Group IIC T6
Shipbuilding approval
Certificate	DNV GL TAA00002UA
EAC Ex
Identification	 2Ex ec IIC T4 Gc
Certificate	BY/112 02.01 TP012 103.01 00079
Shipbuilding data
Temperature	B
Humidity	B
Vibration	A
EMC	A
Enclosure	Required protection according to the Rules shall be provided upon installation on board

EMC data

Electromagnetic compatibility	Conformance with EMC directive
Noise immunity	EN 61000-6-2
Note	When being exposed to interference, there may be minimal deviations.
Noise emission
Standards/regulations	EN 61000-6-4
Electrostatic discharge
Standards/regulations	EN 61000-4-2
Electrostatic discharge
Comments	Safety measures must be taken to prevent electrostatic discharge.
Electromagnetic HF field
Designation	Electromagnetic RF field
Standards/regulations	EN 61000-4-3
Typical deviation from the measuring range final value	0.06 %
Fast transients (burst)
Designation	Fast transients (burst)
Standards/regulations	EN 61000-4-4
Typical deviation from the measuring range final value	0.1 %
Surge current load (surge)
Standards/regulations	EN 61000-4-5
Conducted interference
Designation	Conducted interferences
Standards/regulations	EN 61000-4-6
Typical deviation from the measuring range final value	0.05 %

Standards and regulations

Electrical isolation	3-way isolation

Mounting

Mounting type	DIN rail mounting
Assembly note	The DIN rail connector can be used for bridging the supply voltage. It can be snapped onto a 35 mm EN 60715 DIN rail.
Mounting position	any

Dados comerciais

N.º de artigo	2902055
Pcs./Emb	1 Unidade
Quantidade mínima de pedido	1 Unidade
Chave comercial	DK1
Chave de produto	DK1125
Página de catálogo	Página 84 (C-5-2019)
GTIN	4046356649766
Peso por unidade (inclusive embalagem)	123,5 g
Peso por unidade (excluindo embalagem)	116 g
Número do imposto alfandegário	85437090
País de origem	DE

Classificações

Certificações

Environmental product compliance

EU RoHS
Cumpre os requisitos de substância segundo a Diretiva RoHS	Sim
isenções tanto quanto conhecido	7(a), 7(c)-I
China RoHS
Environment friendly use period (EFUP)	EFUP-50 Uma lista de declaração de acordo com a RoHS da China relativa a artigos encontra-se na área de transferências do respetivo artigo, em "Declaração do fabricante". Para todos os artigos com EFUP-E não é emitida nem necessária uma tabela de declaração de acordo com a RoHS da China.
EU REACH SVHC
Nota sobre as substâncias candidatas ao REACH (n.º CAS)	Lead (n.º CAS: 7439-92-1)
Nota sobre as substâncias candidatas ao REACH (n.º CAS)		2,2',6,6'-tetrabromo-4,4'-isopropylidenediphenol (n.º CAS: 79-94-7)
SCIP	6fd57326-a253-4c34-89d0-81b3b89a6e1a

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

MINI MCR-2-TC-UI - Thermocouple measuring transducer

2902055

Detalhes dos produtos

ECLASS

ETIM

UNSPSC

DNV GL

UL Listed

cUL Listed

IECEx

cUL Listed

UL Listed

ATEX

EAC Ex

Produtos compatíveis

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

MINI MCR-2-TC-UI - Thermocouple measuring transducer 2902055

Detalhes dos produtos

ECLASS

ETIM

UNSPSC

Produtos compatíveis

ME 6,2 TBUS-2 1,5/5-ST-3,81 GY - DIN rail bus connector 2695439

ME 6,2 TBUS-2 1,5/5-ST-3,81 GN - DIN rail bus connector 2869728

TC-D37SUB-AIO16-MP-PS-UNI - Module carrier 2906640

TC-D37SUB-ADIO16-MP-P-UNI - Module carrier 2906639

MINI MCR-2-V8-FLK 16 - System adapter 2901993

MINI MCR-2-V8-MOD-RTU - Communication module 2905634

MINI MCR-2-V8-MOD-TCP - Communication module 2905635

MINI MCR-2-V8-PB-DP - Communication module 2905636

MINI MCR-2-V8-PN - Communication module 2905637

IFS-USB-PROG-ADAPTER - Programming adapter 2811271

IFS-BT-PROG-ADAPTER - Adapter 2905872

TWN4 MIFARE NFC USB ADAPTER - Programming adapter 2909681

FASTCON PRO-SET - Connector set 2906227

FASTCON PRO-SET-PT - Connector set 2906228

UCT-EM (30X5) - Marker for end clamp 0801505

UCT-EM (30X5) CUS - Marker for end clamp 0801589

SK 5,0 WH:REEL - Marker strip 0805221

UC-EMLP (15X5) - Plastic label 0819301

UC-EMLP (15X5) YE - Plastic label 0822615

UC-EMLP (15X5) CUS - Plastic label 0824550

UC-EMLP (15X5) YE CUS - Plastic label 0824551

UC-EMLP (15X5) SR - Plastic label 0828095

UC-EMLP (15X5) SR CUS - Plastic label 0828099

US-EMLP (15X5) - Plastic label 0828790

US-EMLP (15X5) YE - Plastic label 0828873

US-EMLP (15X5) SR - Plastic label 0828874

US-EMLP (15X5) CUS - Plastic label 0830076

US-EMLP (15X5) YE CUS - Plastic label 0830077

US-EMLP (15X5) SR CUS - Plastic label 0830078

UCT-EM (30X5) YE - Marker for end clamp 0830340

UCT-EM (30X5) YE CUS - Marker for end clamp 0830348

MINI MCR-2-PTB - Power terminal block 2902066

MINI MCR-2-PTB-PT - Power terminal block 2902067

QUINT4-SYS-PS/1AC/24DC/2.5/SC - Power supply 2904614

MINI MCR-2-FM-RC - Monitoring block 2904504

MINI MCR-2-FM-RC-PT - Monitoring block 2904508

SZS 0,6X3,5 - Screwdriver 1205053

MINI MCR-2-TC-UI - Thermocouple measuring transducer

2902055