The terminal is designed for use within an Inline station. It has one floating relay changeover contact. You can use the terminal block in protective extra-low voltage applications and in AC applications. When using the terminal block in AC applications, be sure to follow the applicable regulations and safety notes.
IB IL 24/230 DOR1/W-PAC
-
Relay module
2861881
Inline, Relay terminal, Relay output: 1 (floating), Changeover contact, 24 V DC, 230 V AC, for switching ohmic loads, transmission speed in the local bus: 500 kbps, degree of protection: IP20, including Inline connector and labeling field; The product is being prepared for compliance with the Cyber Resilience Act (CRA).
Transferência gratuita disponível.
Downloads
Detalhes dos produtos
| Dimensional drawing |
|
| Width | 12.2 mm |
| Height | 119.8 mm |
| Depth | 71.5 mm |
| Note on dimensions | Housing dimensions |
| Note on application | Only for industrial use |
| Note on application | As things stand now, we are preparing the product so that, as of December 11, 2027, it will comply with the requirements of the EU Cyber Resilience Act (CRA) based on the information currently available regarding the CRA. |
| Utilization restriction | |
| CCCex note | Use in potentially explosive areas is not permitted in China. |
| Mounting type | DIN rail mounting |
| Color (Housing) | gray (RAL 7042) |
| Inline local bus | |
| Number of interfaces | 2 |
| Connection method | Inline data jumper |
| Transmission speed | 500 kbps |
| Programming data | |
| Length code (hex) | C2 |
| ID code (dec.) | 189 |
| Length code (dec) | 194 |
| Process data channel | 2 bit |
| Input address area | 0 Byte |
| Output address area | 2 bit (Only bit0 is occupied) |
| Parameter channel (PCP) | 0 bit |
| Register length (bus) | 2 bit |
| Fieldbus data telegram (PROFIBUS) | |
| Required parameter data | 3 Byte |
| Required configuration data | 4 Byte |
| Relay | |
| Number of outputs | 1 (floating) |
| Connection method | Spring-cage connection |
| Contact switching type | Changeover contact |
| Contact material | AgSnO2, hard gold-plated |
| Contact resistance | ≤ 50 mΩ (at 100 mA/6 V) |
| Nominal output voltage (DC) | 24 V DC |
| Nominal output voltage (AC) | 230 V AC |
| Output voltage range (AC) | 5 V AC ... 253 V AC |
| Output current (max. per channel) | max. 3 A (per channel) |
| Output current (max. per module) | max. 3 A (per module) |
| Inrush current | max. 6 A (for 200 µs, with lamp loads and capacitive loads) |
| Switching voltage | min. 5 V DC |
| max. 250 V DC | |
| max. 253 V AC | |
| Switching current | max. 3 A (At 30 V DC) |
| max. 0.15 A (for 250 V DC) | |
| max. 3 A (at 253 V AC) | |
| Limiting continuous current | 3 A |
| Switching power | max. 750 VA (see to derating) |
| Switching frequency | max. 20 Hz (without load) |
| max. 0.1 Hz (with load) | |
| Coil resistance | 119 Ω ±12 Ω (at 20 °C) |
| Typical response time | typ. 5 ms |
| Bouncing time | typ. 5 ms |
| Typical release time | typ. 6 ms |
| Service life electrical | 105 switching cycles (at 20 switching cycles per minute) |
| Mechanical service life | 2x 107 cycles |
| Common potentials | all contacts floating |
| Product type | I/O component |
| Product family | Inline |
| Type | modular |
| Installation location | Control cabinet |
| Scope of supply | including Inline connector and labeling field |
| Operating mode | Process data mode with 2 bits |
| Special properties | The product is being prepared for compliance with the Cyber Resilience Act (CRA) |
| for switching ohmic loads | |
| Insulation characteristics | |
| Protection class | II (IEC 61140, EN 61140, VDE 0140-1) () |
| Overvoltage category | III (IEC 60664-1, EN 60664-1) |
| Pollution degree | 2 (IEC 60664-1, EN 60664-1) |
| Maximum power dissipation for nominal condition | 0.9 W |
| Potentials: Communications power (UL) | |
| Supply voltage | 7.5 V DC (via voltage jumper) |
| Current draw | max. 60 mA |
| Electrical isolation/isolation of the voltage ranges | |
| Test voltage: Relay contact / Bus logics | 4 kV, 50 Hz, 1 min |
| Test voltage: Contact/contact | 1 kV, 50 Hz, 1 min |
| Test voltage: Contact / PE | 1 kV, 50 Hz, 1 min |
| Connection technology | |
| Connection name | Inline connector |
| Inline connector | |
| Connection method | Spring-cage connection |
| Conductor cross-section, rigid | 0.08 mm² ... 1.5 mm² |
| Conductor cross-section, flexible | 0.08 mm² ... 1.5 mm² |
| Conductor cross-section AWG | 28 ... 16 |
| Stripping length | 8 mm |
| Ambient conditions | |
| Ambient temperature (operation) | -25 °C ... 55 °C |
| Degree of protection | IP20 |
| Air pressure (operation) | 80 kPa ... 106 kPa (up to 2000 m above sea level) |
| Air pressure (storage/transport) | 70 kPa ... 106 kPa (up to 3000 m above sea level) |
| Ambient temperature (storage/transport) | -25 °C ... 85 °C |
| Permissible humidity (operation) | 10 % ... 95 % (non-condensing) |
| Permissible humidity (storage/transport) | 10 % ... 95 % (non-condensing) |
| Mechanical test | |
| Vibration resistance in accordance with EN 60068-2-6/IEC 60068-2-6 | 2g |
| Shock in accordance with EN 60068-2-27/IEC 60068-2-27 | 2g |
ABS
ID de certificação: 22-2226444-PDAcULus Recognized
ID de certificação: E140324cULus Listed
ID de certificação: E199827
Vantagens
Safe isolation
Floating connection for one actuator
Nominal current at the output: 3 A
Total current of the terminal: 3 A