D-SUB connector set, shell size 2, IP67 protection, with shrouds
Detalhes dos produtos
Safety note
Safety note
WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
• The products are suitable for applications in plant, controller, and electrical device engineering.
• When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
• Assembled products may not be manipulated or improperly opened.
• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
• When using the product in direct connection with third-party manufacturers, the user is responsible.
• For operating voltages > 50 V AC, conductive connector housings must be grounded
• Only use tools recommended by Phoenix Contact
• The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product.
• Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products
• Operate the connector only when it is fully plugged in and interlocked.
• Operate the connector only when it is fully plugged in.
• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
• Observe the minimum bending radius of the cable. Lay the cable without twisting it.
• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
Product type
Data connector (cable side)
Application
Housing set
Type
D-SUB
Sensor type
Universal
Number of positions
15
No. of cable outlets
2
Shielded
yes
Cable outlet
angled
Insulation characteristics
Degree of pollution
2
Transmission medium
Copper
Connection technology
Connection method
D-SUB
Color
gray
Flammability rating according to UL 94
V0
Seal material
Flat gasket: NBR; profile gasket: EPDM
Housing material
Plastic
Cable seal material
CR/NBR
External cable diameter
3 mm ... 9 mm
Mechanical data
Insertion/withdrawal cycles
≥ 1000
Ambient conditions
Degree of protection
IP67
Ambient temperature (operation)
-40 °C ... 80 °C
N.º de artigo
1689132
Pcs./Emb
1 Unidade
Quantidade mínima de pedido
1 Unidade
Chave comercial
ABN
Chave de produto
ABNCBA
GTIN
4017918877996
Peso por unidade (inclusive embalagem)
86,2 g
Peso por unidade (excluindo embalagem)
79,4 g
Número do imposto alfandegário
85366990
País de origem
DE
ECLASS
ECLASS-13.0
27440290
ETIM
ETIM 9.0
EC002943
UNSPSC
UNSPSC 21.0
39121400
EU RoHS
Cumpre os requisitos de substância segundo a Diretiva RoHS
Sim
(Sem regras de exceção)
China RoHS
Environment friendly use period (EFUP)
EFUP-E
Nenhuma substância perigosa acima dos valores-limite
EU REACH SVHC
Nota sobre as substâncias candidatas ao REACH (n.º CAS)
