QUINT-PS/1AC/24DC/20 - Power supply - 2866776

Input data

AC operation
Nominal input voltage range	100 V AC ... 240 V AC
Input voltage range	100 V AC ... 240 V AC -15 % ... +10 %
Derating I_{Stat. Boost}	< 100 V AC (1 %/V)
Input voltage range AC	85 V AC ... 264 V AC
Input voltage range DC	90 V DC ... 350 V DC
Electric strength, max.	300 V AC
Typical national grid voltage	120 V AC
Typical national grid voltage		230 V AC
Voltage type of supply voltage	AC
Inrush current	< 20 A
Inrush current integral (I²t)	< 3.2 A²s
Inrush current limitation	20 A
AC frequency range	45 Hz ... 65 Hz
Frequency range DC	0 Hz
Mains buffering time	> 32 ms (120 V AC)
Mains buffering time		> 32 ms (230 V AC)
Current consumption	7 A (100 V AC)
		5.8 A (120 V AC)
		3 A (230 V AC)
		3.1 A (240 V AC)
Nominal power consumption	569 VA
Protective circuit	Transient surge protection; Varistor
Power factor (cos phi)	0.89
Typical response time	< 0.6 s
Input fuse	12 A (slow-blow, internal)
Permissible backup fuse	B10 B16 AC:
Permissible DC backup fuse	DC: Connect a suitable fuse upstream
Recommended breaker for input protection	10 A ... 16 A (Characteristics B, C, D, K)
Discharge current to PE	< 3.5 mA
DC operation
Nominal input voltage range	110 V DC ... 250 V DC
Input voltage range	110 V DC ... 250 V DC -18 % ... +40 %
Derating I_{Stat. Boost}	< 110 V DC (1 %/V)
Current consumption	6.3 A (110 V DC)
Current consumption		2.8 A (220 V DC)

Output data

Efficiency	typ. 92 % (120 V AC)
Efficiency		typ. 92.7 % (230 V AC)
Output characteristic	U/I
Nominal output voltage	24 V DC ±1 %
Setting range of the output voltage (U_Set)	18 V DC ... 29.5 V DC (> 24 V DC, constant capacity restricted)
Nominal output current (I_N)	20 A
POWER BOOST (I_Boost)	26 A (-25 °C ... 40 °C permanent, U_OUT = 24 V DC )
Static Boost (I_Stat.Boost)	26 A
Selective Fuse Breaking (I_SFB)	120 A (12 ms)
Magnetic circuit breaker tripping	B2 / B4 / B6 / B10 / B16 / C2 / C4 / C6
Derating	60 °C ... 70 °C (2.5 %/K)
Feedback voltage resistance	≤ 35 V DC
Protection against overvoltage at the output (OVP)	≤ 35 V DC
Control deviation	< 1 % (change in load, static 10 % ... 90 %)
		< 2 % (change in load, dynamic 10 % ... 90 %)
		< 0.1 % (change in input voltage ±10 %)
Residual ripple	< 30 mV_PP (with nominal values)
Short-circuit-proof	yes
Output power	480 W
Output power		624 W
Maximum no-load power dissipation	8 W
Power loss nominal load max.	40 W
Rise time	< 0.1 s (U_OUT (10 % ... 90 %))
Connection in parallel	yes, for redundancy and increased capacity
Connection in series	yes
Signal: DC OK active
Output description	U_OUT > 0.9 x U_N: High signal
Switching voltage range	18 V DC ... 24 V DC
Maximum inrush current	≤ 20 mA (short-circuit-proof)
Continuous load current	≤ 20 mA
Signal: DC OK floating
Output description	Relay contact, U_OUT > 0.9 x U_N: Contact closed
Maximum switching voltage	30 V AC
Maximum switching voltage		24 V DC
Maximum inrush current	0.5 A
Maximum inrush current		1 A
Continuous load current	≤ 1 A
Signal: POWER BOOST, active
Output description	I_OUT < I_N: High signal
Switching voltage range	18 V DC ... 24 V DC
Output voltage	+ 24 V DC
Maximum inrush current	20 mA (short-circuit-proof)
Continuous load current	≤ 20 mA

Connection data

Input
Connection method	Screw connection
Conductor cross section, rigid min.	0.2 mm²
Conductor cross section, rigid max.	6 mm²
Conductor cross section flexible min.	0.2 mm²
Conductor cross section flexible max.	4 mm²
Conductor cross section AWG min.	18
Conductor cross section AWG max.	10
Stripping length	7 mm
Screw thread	M4
Tightening torque, min	0.5 Nm
Tightening torque max	0.6 Nm
Output
Connection method	Screw connection
Conductor cross section, rigid min.	0.2 mm²
Conductor cross section, rigid max.	6 mm²
Conductor cross section flexible min.	0.2 mm²
Conductor cross section flexible max.	4 mm²
Conductor cross section AWG min.	12
Conductor cross section AWG max.	10
Stripping length	7 mm
Screw thread	M4
Tightening torque, min	0.5 Nm
Tightening torque max	0.6 Nm
Signal
Connection method	Screw connection
Conductor cross section, rigid min.	0.2 mm²
Conductor cross section, rigid max.	6 mm²
Conductor cross section flexible min.	0.2 mm²
Conductor cross section flexible max.	4 mm²
Conductor cross section AWG min.	18
Conductor cross section AWG max.	10
Screw thread	M4
Tightening torque, min	0.5 Nm
Tightening torque max	0.6 Nm

Signaling

Types of signaling	LED
	Active switching output
	Relay contact
Signal output: DC OK active
Status display	U_OUT > 0.9 x U_N: "DC OK" LED green
Note on status display	U_OUT < 0.9 x U_N: Flashing "DC OK" LED
	I_OUT < I_N: LED ON
Signal output: DC OK floating
Status display	U_OUT > 0.9 x U_N: "DC OK" LED green
Note on status display	U_OUT < 0.9 x U_N: Flashing "DC OK" LED
Signal output: POWER BOOST, active
Status display	I_OUT > I_N: LED "BOOST" yellow

Electrical properties

Number of phases	1
Insulation voltage input/output	4 kV AC (type test)
	2 kV AC (routine test)
Insulation voltage output / PE	500 V DC (routine test)
Insulation voltage input / PE	3.5 kV AC (type test)
	2 kV AC (routine test)

Product properties

Product type	Power supply
Product family	QUINT POWER
MTBF (IEC 61709, SN 29500)	> 900000 h (25 °C)
	> 520000 h (40 °C)
	> 235000 h (60 °C)
Insulation characteristics
Protection class	I
Degree of pollution	2

Dimensions

Width	90 mm
Height	130 mm
Depth	125 mm
Installation dimensions
Installation distance right/left	5 mm / 5 mm
Installation distance top/bottom	50 mm / 50 mm
Alternative assembly
Width	122 mm
Height	130 mm
Depth	93 mm

Mounting

Mounting type	DIN rail mounting
Assembly note	alignable: P_N ≥50%, 5 mm horizontally, 15 mm next to active components, 50 mm vertically alignable: P_N <50%, 0 mm horizontally, 40 mm vertically top, 20 mm vertically bottom
Mounting position	horizontal DIN rail NS 35, EN 60715
With protective coating	no

Material specifications

Housing material	Metal
Hood version	Galvanized sheet steel, free from chrome (VI)
Side element version	Aluminum

Environmental and real-life conditions

Ambient conditions
Degree of protection	IP20
Ambient temperature (operation)	-25 °C ... 70 °C (> 60 °C Derating: 2,5 %/K)
Ambient temperature (storage/transport)	-40 °C ... 85 °C
Ambient temperature (start-up type tested)	-40 °C
Maximum altitude	≤ 5000 m (> 2000 m, observe derating)
Climatic class	3K22 (in accordance with EN 60721-3-3)
Max. permissible relative humidity (operation)	≤ 95 % (at 25 °C, non-condensing)
Shock	18 ms, 30g, in each space direction (according to IEC 60068-2-27)
Vibration (operation)	< 15 Hz, amplitude ±2.5 mm (according to IEC 60068-2-6)
	15 Hz ... 150 Hz, 2.3g, 90 min.
Temp code	T4 (-25 ... +70 °C; > 60 °C, Derating: 2,5 %/K)

Standards and regulations

Rail applications	EN 50121-4
Rail applications		EN 50121-3-2
HART FSK Physical Layer Test Specification Compliance	Output voltage U_Out compliant
Standard – Limitation of mains harmonic currents	EN 61000-3-2
Standard - Electrical safety	IEC 61010-2-201 (SELV)
Standard - Equipment safety	BG (design tested)
Standard - Approval for medical use	IEC 60601-1, 2 x MOOP
Standard – Safety extra-low voltage	IEC 61010-1 (SELV)
Standard – Safety extra-low voltage		IEC 61010-2-201 (PELV)
Standard - Safe isolation	IEC 61010-2-201
Standard - safety for equipment for measurement, control, and laboratory use	IEC 61010-1
Approval - requirement of the semiconductor industry with regard to mains voltage dips	SEMI F47-0706 Compliance Certificate
Overvoltage category
EN 61010-1	II (≤ 5000 m)
EN 62477-1	III (≤ 2000 m)
EN 61558-2-16	II (≤ 4000 m)

Approvals

CSA	CAN/CSA-C22.2 No. 60950-1-07
	CSA-C22.2 No. 107.1-01
Shipbuilding approval	DNV GL (EMC B, only with upstream filter), ABS, LR, RINA, NK, BV
SIQ	BG (type approved)
UL approvals	UL Listed UL 508
	UL/C-UL Recognized UL 60950-1
	UL 121201 & CSA C22.2 No. 213-17 Class I, Division 2, Groups A, B, C, D T4 (Hazardous Location)

EMC data

Electromagnetic compatibility	Conformance with EMC Directive 2014/30/EU
Low Voltage Directive	Conformance with Low Voltage Directive 2014/35/EC
EMC requirements for noise emission	EN 61000-6-3
EMC requirements for noise emission		EN 61000-6-4
EMC requirements for noise immunity	EN 61000-6-1
EMC requirements for noise immunity		EN 61000-6-2
Noise emission
Standards/regulations	EN 55011 (EN 55022)
Electrostatic discharge
Standards/regulations	EN 61000-4-2
Electrostatic discharge
Contact discharge	8 kV (Test Level 4)
Discharge in air	15 kV (Test Level 4)
Comments	Criterion A
Electromagnetic HF field
Standards/regulations	EN 61000-4-3
Electromagnetic HF field
Frequency range	80 MHz ... 1 GHz
Test field strength	20 V/m (Test Level 3)
Frequency range	1 GHz ... 2 GHz
Test field strength	10 V/m (Test Level 3)
Frequency range	2 GHz ... 3 GHz
Test field strength	10 V/m (Test Level 3)
Comments	Criterion A
Fast transients (burst)
Standards/regulations	EN 61000-4-4
Fast transients (burst)
Input	4 kV (Test Level 4 - asymmetrical)
Output	2 kV (Test Level 3 - asymmetrical)
Signal	2 kV (Test Level 4 - asymmetrical)
Comments	Criterion A
Surge voltage load (surge)
Standards/regulations	EN 61000-4-5
Surge voltage load (surge)
Input	2 kV (Test Level 3 - symmetrical)
Input		4 kV (Test Level 4 - asymmetrical)
Output	1 kV (Test Level 2 - symmetrical)
Output		2 kV (Test Level 3 - asymmetrical)
Signal	1 kV (Test Level 2 - asymmetrical)
Comments	Criterion A
Conducted interference
Standards/regulations	EN 61000-4-6
Conducted interference
Input/output/signal	asymmetrical
Frequency range	0.15 MHz ... 80 MHz
Comments	Criterion A
Voltage	10 V (Test Level 3)
Emitted interference
Standards/regulations	EN 61000-6-3
Radio interference voltage in acc. with EN 55011	EN 55011 (EN 55022) Class B, area of application: Industry and residential
Emitted radio interference in acc. with EN 55011	EN 55011 (EN 55022) Class B, area of application: Industry and residential
Criteria
Criterion A	Normal operating behavior within the specified limits.
Criterion B	Temporary impairment to operational behavior that is corrected by the device itself.

N.º de artigo	2866776
Pcs./Emb	1 Unidade
Quantidade mínima de pedido	1 Unidade
Chave comercial	CMP
Chave de produto	CMPQ13
Página de catálogo	Página 159 (C-6-2015)
GTIN	4046356113557
Peso por unidade (inclusive embalagem)	2 230 g
Peso por unidade (excluindo embalagem)	1 608 g
Número do imposto alfandegário	85044095
País de origem	TH

EU RoHS
Cumpre os requisitos de substância segundo a Diretiva RoHS	Sim
isenções tanto quanto conhecido	6(c), 7(a), 7(c)-I
China RoHS
Environment friendly use period (EFUP)	EFUP-25 Uma lista de declaração de acordo com a RoHS da China relativa a artigos encontra-se na área de transferências do respetivo artigo, em "Declaração do fabricante". Para todos os artigos com EFUP-E não é emitida nem necessária uma tabela de declaração de acordo com a RoHS da China.
EU REACH SVHC
Nota sobre as substâncias candidatas ao REACH (n.º CAS)	Lead (n.º CAS: 7439-92-1)
SCIP	28e0effb-0c7a-483b-a45b-1260d63e337e
EF3.0 Alterações climáticas
CO2e kg	58,942 kg CO2e

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

QUINT-PS/1AC/24DC/20 - Power supply

2866776

Detalhes dos produtos

ECLASS

ETIM

UNSPSC

EAC

LR

NK

BV

EAC

UL Listed

BSH

RINA

ABS

Type approved

SEMI F47

EAC

DNV

BIS Licence Document

IECEE CB Scheme

IECEE CB Scheme

UL Listed

Produtos compatíveis

Vantagens

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

QUINT-PS/1AC/24DC/20 - Power supply 2866776

Detalhes dos produtos

ECLASS

ETIM

UNSPSC

Produtos compatíveis

QUINT-DIODE/12-24DC/2X20/1X40 - Redundancy module 2320157

QUINT-ORING/24DC/2X20/1X40 - Redundancy module, with protective coating 2320186

ME-MAX-NEF/QUINT20A - EMC filter 2319919

CB TM1 1A SFB P - Thermal-magnetic device circuit breaker 2800836

CB TM1 2A SFB P - Thermal-magnetic device circuit breaker 2800837

CB TM1 3A SFB P - Thermal-magnetic device circuit breaker 2800838

CB TM1 4A SFB P - Thermal-magnetic device circuit breaker 2800839

CB TM1 5A SFB P - Thermal-magnetic device circuit breaker 2800840

CB TM1 6A SFB P - Thermal-magnetic device circuit breaker 2800841

CB TM1 8A SFB P - Thermal-magnetic device circuit breaker 2800842

CB TM1 10A SFB P - Thermal-magnetic device circuit breaker 2800843

UWA 182/52 - Mounting adapter 2938235

UTA 107 - DIN rail adapter 2853983

QUINT-PS/FAN/4 - Fan 2320076

PLT-SEC-T3-230-FM-UT - Type 3 surge protection device 2907919

PLT-SEC-T3-24-FM-UT - Type 3 surge protection device 2907916

Vantagens

QUINT-PS/1AC/24DC/20 - Power supply

2866776