Further information about the CAPAROC product family can be found in the online manual at: phoenixcontact.com/caparoc-help
CAPAROC PM EC
-
Feed-in module
1687560
Feed-in module with EtherCAT® interface for supplying the CAPAROC circuit breaker system with 12 V DC or 24 V DC. Additional system interface for communication with the power supply. For DIN rail installation via the CAPAROC current rails.
Este produto precisa de outros produtos para a operação.
Acessórios necessários
Transferência gratuita disponível.
Downloads
Detalhes dos produtos
| General | |
| Note | LABS release – in accordance with test specification VW PV 3.10.7:2005-0 |
| When connecting the conductor, make sure that the CAPAROC modules are not pulled apart due to tensile force. Gaps must not be created between the modules. | |
| EtherCAT® is a registered trademark and patented technology, licensed by Beckhoff Automation GmbH, Germany. | |
| Product type | Device circuit breakers |
| Product family | CAPAROC |
| Type | Plug-in module |
| Number of slots | 4 |
| Insulation characteristics | |
| Protection class | III |
| Pollution degree | 2 |
| EtherCAT® | |
| Device function | EtherCAT® SubDevice |
| General | |
| Operating voltage | 10 V DC ... 30 V DC |
| Rated voltage | 12 V DC |
| 24 V DC | |
| Rated current IN | 45 A DC (Total current input) |
| Rated surge voltage | 0.5 kV |
| Tripping method | E (electronic) |
| Feedback resistance | max. 35 V DC |
| Dielectric strength | 35 V DC (Load circuit) |
| Efficiency | > 99 % |
| Closed circuit current I0 | typ. 46 mA (no load at 24 V) |
| Power dissipation | typ. 1.1 W (no load at 24 V) |
| < 4.5 W (at 40 A) | |
| Temperature derating | 45 A (Total current at 60°C) |
| 20 A (Total current at 65 °C) | |
| 45 A (Total current at 60°C, in accordance with UL) | |
| MTBF (IEC 61709, SN 29500) | 7242508.37 h (at 25 °C with 21 % load) |
| 3958056.77 h (at 40°C with 34.25% load) | |
| 764697.81 h (at 60°C with 100% load) | |
| Voltage drop | 0.082 V (at 40 A) |
| Load circuit | |
| Undervoltage switch-off | ≤ 9.2 V DC (active) |
| ≥ 10.2 V DC (inactive) | |
| Overvoltage switch-off | ≥ 30.5 V DC (active) |
| ≤ 29.5 V DC (inactive) | |
| Main circuit IN+ | |
| Connection method | Push-in connection |
| Stripping length | 18 mm |
| Conductor cross-section AWG | 20 ... 8 |
| Conductor cross-section, flexible, with ferrule, with plastic sleeve | 0.5 mm² ... 16 mm² |
| Conductor cross-section flexible, with ferrule without plastic sleeve | 0.5 mm² ... 16 mm² |
| Main circuit IN- | |
| Connection method | Push-in connection |
| Stripping length | 18 mm |
| Conductor cross-section AWG | 20 ... 8 |
| Conductor cross-section, flexible, with ferrule, with plastic sleeve | 0.5 mm² ... 16 mm² |
| Conductor cross-section flexible, with ferrule without plastic sleeve | 0.5 mm² ... 16 mm² |
| System communication | |
| Connection method | Push-in connection |
| Stripping length | 8 mm |
| Conductor cross-section rigid | 0.2 mm² ... 1.5 mm² |
| Conductor cross-section AWG | 24 ... 16 |
| Conductor cross-section, flexible, with ferrule, with plastic sleeve | 0.2 mm² ... 0.75 mm² |
| Conductor cross-section flexible, with ferrule without plastic sleeve | 0.2 mm² ... 1.5 mm² |
| Maximum system extension | ≤ 16 (CAPAROC modules alignable) |
| Interface type | Ethernet |
| Number | 2 |
| Transmission speed | 10 Mbps 100 Mbps |
| Transmission physics | Ethernet in RJ45 twisted pair |
| Protocols supported | EtherCAT® SubDevice, CoE, FoE, EoE |
| Power (PWR) LED green | lit (Supply voltage within the operating voltage range) |
| 3x flashing (Global programming lock deactivated) | |
| Power (PWR) LED red | lit (Supply voltage outside the operating voltage range) |
| 5x flashing (Factory reset command accepted) | |
| Power (PWR) LED yellow | lit (PWR button pressed) |
| 3x flashing (Global programming lock activated) | |
| Ready (RDY) LED yellow | flashing (Firmware update is running) |
| Ready (RDY) LED green | lit (Firmware started successfully) |
| Error (ERR) LED red | off (No communication error. The device’s EtherCAT® communication is working perfectly.) |
| flashing quickly (Invalid configuration/general configuration error Possible reason:A state change triggered by the main device is not possible due to register or object settings.The most common reason is an outdated module slot configuration.) | |
| flashing (Local error: The SubDevice application has changed the EtherCAT® state independently. Possible reason 1: A host watchdog timeout has occurred.Possible reason 2: Incorrect module configuration occurred during operation. Module replaced by wrong module.) | |
| two flashes (Watchdog timeout of the application) | |
| Run (RUN) LED green | off (Device is in the INIT state) |
| flashing quickly (2.5 Hz) (Device is in the PRE-OPERATIONAL state) | |
| flashing (Device is in the SAFE-OPERATIONAL state) | |
| lit (Device is in the OPERATIONAL state) |
| Dimensional drawing |
|
| Width | 24.8 mm |
| Height | 132.4 mm |
| Depth | 111.3 mm (incl. DIN rail 7.5 mm) |
| Color | light gray (RAL 7035) |
| Material | PA 6 |
| PA 6 | |
| PA 6 | |
| PC | |
| Flammability rating according to UL 94 | V-0 |
| Ambient conditions | |
| Degree of protection | IP20 |
| Ambient temperature (operation) | -30 °C ... 65 °C |
| -30 °C ... 60 °C (in acc. with UL) | |
| Ambient temperature (storage/transport) | -40 °C ... 70 °C |
| Altitude | ≤ 4000 m (amsl) |
| Humidity test | 96 h, 95 % RH, 40 °C |
| Shock (operation) | 30g (11 ms period, half-sine shock pulse, according to IEC 60068-2-27) |
| 25g (6 ms duration, half-sine shock pulse in accordance with IEC 60068-2-27, continuous shock) | |
| Vibration (operation) | 5g (10 Hz ... 150 Hz / 10 cycles / axis / X, Y, Z) |
| UL approval | |
| Identification | UL/C-UL Listed UL 508 |
| UL 121201 Class I, Division 2, Groups A, B, C, D, T4A | |
| Standards/specifications | EN 61000-6-2 |
| Note | EMC – Immunity for industrial areas |
| Standards/specifications | EN 61000-6-4 |
| Note | EMC – Immunity for industrial areas |
| Standards/specifications | EN 61000-6-8 |
| Note | EMC interference emission for professional devices that are used in business and commercial areas as well as in small businesses |
| Standards/specifications | EN 60068-2-78 |
| Note | Environmental influences – Moisture and heat, constant |
| Standards/specifications | EN 50178 |
| Note | Equipping power installations with electronic equipment |
| Standards/specifications | EN 60068-2-6 |
| Note | Environmental influences – Vibrations (sinusoidal) |
| Standards/specifications | EN 60068-2-27 |
| Note | Environmental influences – Shocks |
| Mounting type | pluggable onto CAPAROC CR… current rail |
cUL Listed
ID de certificação: E123528cULus Listed
ID de certificação: E483407
Vantagens
The benchmark that you can customize by selecting single signals and resets all the way to EtherCAT® communication
Particularly easy operation for everyone with tool-free assembly, direct feed-in to the busbar, and clear operating states
Exceptionally easy design-in with the comprehensive digital data packet for use in EtherCAT® applications