SACC-E-S15MS-5PE-M20/0,25 - Device connector front mounting
1514512
Device connector front mounting, 6-position, Pin, straight, S15, on free cable end, Individual wires, cable length: 0.25 m, 2.50 mm2
Detalhes dos produtos
Notes on operation
The electrical and mechanical data specified assume that the connector pair is correctly locked and mounted. If the connector is unlocked and if there is a danger of contamination, the connector must be sealed using a protective cap > IP54. Influences arising from litz wires, cables or PCB assembly must also be taken into consideration.
Safety note
Safety note
WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
• The products are suitable for applications in plant, controller, and electrical device engineering.
• When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
• Assembled products may not be manipulated or improperly opened.
• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
• When using the product in direct connection with third-party manufacturers, the user is responsible.
• For operating voltages > 50 V AC, conductive connector housings must be grounded
• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
• Observe the corresponding technical data. You will find information: o On the product o On the packing label o In the supplied documentation o Online at phoenixcontact.com/products under the product
• Only use tools recommended by Phoenix Contact
• Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products
• Ensure that the protective or functional ground has been properly connected.
• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).
Mounting type
Front mounting (M20 x 1,5)
Product type
Circular connectors (device side)
Application
Power
Number of positions
6
No. of cable outlets
1
Shielded
no
Thread type
S15
Insulation characteristics
Degree of pollution
3
Contact material
Cu alloy
Contact surface material
Ag
Contact carrier material
PA
Material for screw connection
PA
Conductor material
Bare Cu litz wires
Nominal voltage UN
600 V AC (Power)
63 V (Signal)
Nominal current IN
16 A (Power)
10 A (Signal)
Conductor connection
Connection method
Individual wires
Contact connection type
Pin
Conductor cross-section
6x 2.5 mm²
Connection 1
Head design
Pin
Head cable outlet
straight
Head thread type
S15
Connection 2
Head design
free cable end
Cable length
0.25 m
Single wire, color
Black 1, black 2, black 3, green/yellow, blue A, blue B
Cable cross section
6x 2.5 mm²
Conductor material
Bare Cu litz wires
Material wire insulation
PUR
Halogen-free
yes
Ambient temperature (operation)
-40 °C ... 70 °C (cable, fixed installation)
Ambient conditions
Degree of protection
IP67
Ambient temperature (operation) (Cable, fixed installation)
-40 °C ... 70 °C (cable, fixed installation)
Standard designation
S15 connector
Standards/specifications
according to IEC 61076-2-116
N.º de artigo
1514512
Pcs./Emb
1 Unidade
Quantidade mínima de pedido
1 Unidade
Chave comercial
ABQ
Chave de produto
ABQODA
GTIN
4063151978600
Peso por unidade (inclusive embalagem)
73,2 g
Peso por unidade (excluindo embalagem)
22,22 g
Número do imposto alfandegário
85444290
País de origem
DE
ECLASS
ECLASS-13.0
27440103
ECLASS-15.0
27440103
ETIM
ETIM 10.0
EC003570
EU RoHS
Cumpre os requisitos de substância segundo a Diretiva RoHS
Sim
isenções tanto quanto conhecido
6(c)
China RoHS
Environment friendly use period (EFUP)
EFUP-50
Uma lista de declaração de acordo com a RoHS da China relativa a artigos encontra-se na área de transferências do respetivo artigo, em "Declaração do fabricante". Para todos os artigos com EFUP-E não é emitida nem necessária uma tabela de declaração de acordo com a RoHS da China.
EU REACH SVHC
Nota sobre as substâncias candidatas ao REACH (n.º CAS)
