VC-TFS 4 - Contact insert

1607460

Contact insert, Range of articles: VARIOCON, design: VC2, color: light grey, number of positions: 4, min. conductor cross-section: 0.5 mm², max. conductor cross-section: 16 mm², rated current: 70 A, Connection method: Screw connection

Detalhes dos produtos

Safety note
Safety note	WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
	• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
	• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
	• The products are suitable for applications in plant, controller, and electrical device engineering.
	• When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
	• Assembled products may not be manipulated or improperly opened.
	• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
	• When using the product in direct connection with third-party manufacturers, the user is responsible.
	• For operating voltages > 50 V AC, conductive connector housings must be grounded
	• Ensure that the protective or functional ground has been properly connected.
	• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
	• Observe the corresponding technical data. You will find information: o On the product o On the packing label o In the supplied documentation o Online at phoenixcontact.com/products under the product
	• Only use tools recommended by Phoenix Contact
	• The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product.
	• Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products
	• Operate the connector only when it is fully plugged in.
	• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
	• Observe the minimum bending radius of the cable. Lay the cable without twisting it.
	• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).

Product family	VARIOCON
Type	VC2
Number of positions	4
Insulation characteristics
Degree of pollution	3

Rated voltage (II/2)	1000 V
Rated voltage (III/2)	1000 V
Rated voltage (III/3)	690 V
Rated surge voltage	6 kV
Rated surge voltage (II/2)	6 kV
Rated surge voltage (III/2)	8 kV
Rated surge voltage (III/3)	8 kV
Rated current	70 A
	70 A

Connection method	Screw connection
Tightening torque	1.2 ... 1.8 Nm
Cross section AWG	20 ... 6
Screw thread	M4

Width	58 mm
Height	27 mm
Length	41.1 mm

Color	light grey
Color of the housing part	gray
Material Housing	PA 6.6
Material Contact	CuZn
Material Contact carrier	PA 6.6
Flammability rating according to UL 94	V0
Insulating material group	I
Contact surface material	nickel-plated

Single wire, cross section	0.5 mm² 16 mm²
Stripping length of the individual wire	12 mm
Halogen-free	yes

Mechanical data
Insertion/withdrawal cycles	≥ 50

Ambient conditions
Ambient temperature (operation)	-40 °C ... 100 °C

Dados comerciais

N.º de artigo	1607460
Pcs./Emb	10 Unidade
Quantidade mínima de pedido	10 Unidade
Chave comercial	ABL
Chave de produto	ABLACC
GTIN	4017918943578
Peso por unidade (inclusive embalagem)	45,11 g
Peso por unidade (excluindo embalagem)	38,015 g
Número do imposto alfandegário	85366990
País de origem	PL

Classificações

Certificações

Approval Specification Data
	Tensão nominal U_N	Corrente nominal I_N	Secção transversal American Wire Gauge	Secção transversal mm²
keine
	600 V	45 A	20 - 6

Approval Specification Data
	Tensão nominal U_N	Corrente nominal I_N	Secção transversal American Wire Gauge	Secção transversal mm²
keine
	600 V	55 A	20 - 6

Environmental product compliance

Produtos compatíveis

Acessórios

Phoenix Contact S.A.

Sintra Business Park, Edifício n°1 Zona Industrial da Abrunheira, sala 0M, 2710-089 SINTRA

Fazer uma pergunta (+351) 21 911 2760 pt-info@phoenixcontact.com

EU RoHS
Cumpre os requisitos de substância segundo a Diretiva RoHS	Sim (Sem regras de exceção)
China RoHS
Environment friendly use period (EFUP)	EFUP-E Nenhuma substância perigosa acima dos valores-limite
EU REACH SVHC
Nota sobre as substâncias candidatas ao REACH (n.º CAS)	Nenhuma substância numa proporção superior a 0,1 % em massa

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

VC-TFS 4 - Contact insert

1607460

Detalhes dos produtos

ECLASS

ETIM

UNSPSC

cUL Recognized

UL Recognized

Produtos compatíveis

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

VC-TFS 4 - Contact insert 1607460

Detalhes dos produtos

ECLASS

ETIM

UNSPSC

Produtos compatíveis

CP-MSTB - Coding profile 1734634

CP-HCC 4 - Coding profile 1600027

SK U/5,0 WH:UNBEDRUCKT - Marker card 0803922

SK U/3,8 WH:UNBEDRUCKT - Marker card 0803906

SK 7,5/3,8:FORTL.ZAHLEN - Marker card 0804455

SK 5/3,8:FORTL.ZAHLEN - Marker card 0804183

SK 3,5/2,8:FORTL.ZAHLEN - Marker card 0804073

VC-TFS 4 - Contact insert

1607460