1. Página inicial
  2. Produtos
  3. Connectors and cables
  4. Circular connectors
  5. Panel feed-through - ST-6EP1N8ACK02S
The figure shows the 4-position version
Installation dimensions
Connector pin assignment
I = current strength, ϑ = ambient temperature, 3x 14 A + 2x 2 A constant

Panel feed-through - ST-6EP1N8ACK02S
1618776

Panel feed-through, straight, SPEEDCON locking, M17, number of positions: 6+PE, type of contact: Pin, Flat gasket, 4x Ø 3.2, shielded: yes, flange dimensions: 25.75 mm x 25.75 mm, degree of protection: IP67, cable diameter range: 3.5 mm ... 5.5 mm, number of positions: 7, connection method: Crimp connection, series: ST

Detalhes dos produtos

Order information: Order crimp contacts Ø 1 mm separately
Safety note
Safety note WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
• The products are suitable for applications in plant, controller, and electrical device engineering.
• When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
• Assembled products may not be manipulated or improperly opened.
• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
• When using the product in direct connection with third-party manufacturers, the user is responsible.
• For operating voltages > 50 V AC, conductive connector housings must be grounded
• Ensure that the protective or functional ground has been properly connected.
• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
• Only use tools recommended by Phoenix Contact
• The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product.
• Operate the connector only when it is fully plugged in and interlocked.
• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
• Observe the minimum bending radius of the cable. Lay the cable without twisting it.
• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).
Product type Circular connectors (device side)
Number of positions 7
Connection profile 6+PE
Application Power
Locking type SPEEDCON locking
Series ST
Shielded yes
Coding N
Thread type M17
Degree of protection IP67
Ambient temperature (operation) -40 °C ... 125 °C
Housing
Flange dimensions 25.75 mm x 25.75 mm
Type straight
Direction of rotation Standard
Contact
Contact diameter 1 mm
Max. current 14 A
Nominal voltage UN 630 V
Overvoltage category III
Rated surge voltage 6 kV
Contact
Contact diameter 1 mm
Connection technology
Connection method Crimp connection
Conductor connection
Connection method Crimp connection
Mounting 4x Ø 3.2
Cable structure
External cable diameter 3.5 mm ... 5.5 mm
N.º de artigo 1618776
Pcs./Emb 1 Unidade
Quantidade mínima de pedido 1 Unidade
Observação Produção ligada a pedido (sem devolução)
Chave comercial ABR
Chave de produto ABRCEK
Página de catálogo Página 135 (C-2-2019)
GTIN 4046356817349
Peso por unidade (inclusive embalagem) 44,44 g
Peso por unidade (excluindo embalagem) 44,44 g
Número do imposto alfandegário 85366990
País de origem DE

ECLASS

ECLASS-9.0 27440102
ECLASS-10.0.1 27440102
ECLASS-11.0 27440102

ETIM

ETIM 8.0 EC002635

UNSPSC

UNSPSC 21.0

cUL Recognized

Approval ID: FILE E 335019

UL Recognized

Approval ID: FILE E 335019

EAC

Approval ID: B.01687

UL Recognized

Approval ID: E153698-20140124

cUL Recognized

Approval ID: E153698-20140124
REACh SVHC Lead 7439-92-1
China RoHS Environmentally Friendly Use Period = 50 years
For information on hazardous substances, refer to the manufacturer’s declaration available under “Downloads”

Produtos compatíveis

  1. Crimp contact ST-10KP010 - 1618255

  2. Crimp contact ST-10KP035 - 1618458

  3. Protective cap ST-Z0023 - 1621049

  4. Color-coding ST-Z0016 - 1617993

  5. Color-coding ST-Z0017 - 1618049

  6. Color-coding ST-Z0018 - 1618050

Vantagens

Reduced size: ideal for compact devices
Consistent EMC protection for reliable connection solutions in the industrial environment
Crimping connection: vibration- and temperature-resistant assembly
Flexible use: reliably connect various cable diameters
User-specific, suitable for front and rear mounting