1. Página inicial
  2. Produtos
  3. Connectors and cables
  4. Circular connectors
  5. Device connector, front mounting - ST-5EP1N8AAE00S
The figure shows the 4-pos. (3+PE) product version
Dimensional drawing
Connector pin assignment
I = current strength, ϑ = ambient temperature, 3x 14 A + 2x 2 A constant

Device connector, front mounting - ST-5EP1N8AAE00S
1618127

Device connector, front mounting, angled rotatable, SPEEDCON locking, M17, number of positions: 5+PE, type of contact: Pin, Axial O-ring, 4x Ø 3.2, shielded: yes, flange dimensions: 25 mm x 25 mm, degree of protection: IP67, number of positions: 6, connection method: Crimp connection, series: ST

Detalhes dos produtos

Order information: Order crimp contacts Ø 1 mm separately
Safety note
Safety note WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
• The products are suitable for applications in plant, controller, and electrical device engineering.
• When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
• Assembled products may not be manipulated or improperly opened.
• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
• When using the product in direct connection with third-party manufacturers, the user is responsible.
• For operating voltages > 50 V AC, conductive connector housings must be grounded
• Ensure that the protective or functional ground has been properly connected.
• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
• Only use tools recommended by Phoenix Contact
• The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product.
• Operate the connector only when it is fully plugged in and interlocked.
• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
• Observe the minimum bending radius of the cable. Lay the cable without twisting it.
• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).
Product type Circular connectors (device side)
Number of positions 6
Connection profile 5+PE
Application Power
Locking type SPEEDCON locking
Series ST
Shielded yes
Coding N
Thread type M17
Degree of protection IP67
Ambient temperature (operation) -40 °C ... 125 °C
Altitude 3000 m
Housing
Flange dimensions 25 mm x 25 mm
Type angled rotatable
Direction of rotation Standard
Contact
Contact diameter 1 mm
Max. current 14 A
Nominal voltage UN 630 V
Overvoltage category III
Rated surge voltage 6 kV
Contact
Contact diameter 1 mm
Seal material FPM
Housing material Metal
Connection technology
Connection method Crimp connection
Conductor connection
Connection method Crimp connection
Mounting 4x Ø 3.2
N.º de artigo 1618127
Pcs./Emb 16 Unidade
Quantidade mínima de pedido 16 Unidade
Observação Produção ligada a pedido (sem devolução)
Chave comercial ABR
Chave de produto ABRCAL
GTIN 4046356580755
Peso por unidade (inclusive embalagem) 98,312 g
Peso por unidade (excluindo embalagem) 63,78 g
Número do imposto alfandegário 85366990
País de origem DE

ECLASS

ECLASS-9.0 27440312
ECLASS-10.0.1 27440312
ECLASS-11.0 27440312

ETIM

ETIM 8.0 EC002641

UNSPSC

UNSPSC 21.0

cUL Recognized

Approval ID: FILE E 335019

UL Recognized

Approval ID: FILE E 335019

EAC

Approval ID: B.01687

UL Listed

Approval ID: E468743-20210825
Approval Specification Data
Tensão nominal UN Corrente nominal IN Secção transversal American Wire Gauge Secção transversal mm2
Power 600 V 10 A - 18
Signal 60 V 2 A - 20

cUL Listed

Approval ID: E468743-20210825
Approval Specification Data
Tensão nominal UN Corrente nominal IN Secção transversal American Wire Gauge Secção transversal mm2
Power 600 V 8 A - 18
Signal 60 V 2 A - 20

UL Recognized

Approval ID: E153698-20140124

cUL Recognized

Approval ID: E153698-20140124

cULus Listed

China RoHS Environmentally friendly use period: unlimited = EFUP-e
No hazardous substances above threshold values

Produtos compatíveis

  1. Crimp contact ST-10KP010 - 1618255

  2. Crimp contact ST-10KP035 - 1618458

  3. Protective cap ST-Z0006 - 1607776

  4. Color-coding ST-Z0019 - 1620621

  5. Color-coding ST-Z0020 - 1620622

  6. Color-coding ST-Z0021 - 1620623

  7. Metal protective cap ST-Z0014 - 1616069

  8. Metal protective cap ST-Z0013 - 1616068