ST-5EP1N8AAD00S - Device connector front mounting

1607709

Device connector front mounting, angled rotatable, SPEEDCON, M17, number of positions: 5+PE, contact connection type: Pin, Axial O-ring, shielded: yes, flange dimensions: 21.6 mm x 21.6 mm, number of positions: 6, connection method: Crimp connection, series: ST

Detalhes dos produtos

Order information:	Order crimp contacts Ø 1 mm separately
Safety note
Safety note	WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
	• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
	• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
	• The products are suitable for applications in plant, controller, and electrical device engineering.
	• When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
	• Assembled products may not be manipulated or improperly opened.
	• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
	• When using the product in direct connection with third-party manufacturers, the user is responsible.
	• For operating voltages > 50 V AC, conductive connector housings must be grounded
	• Ensure that the protective or functional ground has been properly connected.
	• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
	• Only use tools recommended by Phoenix Contact
	• The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product.
	• Operate the connector only when it is fully plugged in and interlocked.
	• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
	• Observe the minimum bending radius of the cable. Lay the cable without twisting it.
	• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).

Mounting type	Front mounting/square flange 4x Ø 2,7 mm
Assembly note	4x Ø 2,7 mm

Product type	Circular connectors (device side)
Series	ST
Application	Power
Number of positions	6
Connection profile	5+PE
Shielded	yes
Coding	N
Thread type	M17

Housing
Flange dimensions	21.6 mm x 21.6 mm

Seal material	FPM
Housing material	Metal
Housing material	Turned parts: copper zinc alloy (CuZn), die-cast parts: zinc (GD-Zn)
Insulator material	PA 6.6
Gasket and O-ring material	FPM

Contact
Contact diameter	1 mm
Max. current	14 A
Nominal voltage U_N	630 V
Overvoltage category	III
Degree of pollution	3
Rated surge voltage	6 kV
Contact
Contact diameter	1 mm

Conductor connection
Connection method	Crimp connection
Contact connection type	Pin

Type	angled rotatable
Direction of rotation	Standard

Ambient conditions
Degree of protection	IP67
Ambient temperature (operation)	-40 °C ... 125 °C
Ambient temperature (storage/transport)	15 °C ... 25 °C
Altitude	3000 m
Permissible humidity (storage/transport)	50 % ... 65 %

Dados comerciais

N.º de artigo	1607709
Pcs./Emb	16 Unidade
Quantidade mínima de pedido	16 Unidade
Observação	Produção ligada a pedido (sem devolução)
Chave comercial	ABR
Chave de produto	ABRBEM
GTIN	4046356274128
Peso por unidade (inclusive embalagem)	95,43 g
Peso por unidade (excluindo embalagem)	75,63 g
Número do imposto alfandegário	85366990
País de origem	DE

Classificações

Certificações

Approval Specification Data
	Tensão nominal U_N	Corrente nominal I_N	Secção transversal American Wire Gauge	Secção transversal mm²
Power	600 V	10 A		18
Signal	60 V	2 A		20

Approval Specification Data
	Tensão nominal U_N	Corrente nominal I_N	Secção transversal American Wire Gauge	Secção transversal mm²
Power	600 V	8 A	18
Signal	60 V	2 A	20

Environmental product compliance

Produtos compatíveis

Acessórios

Phoenix Contact S.A.

Sintra Business Park, Edifício n°1 Zona Industrial da Abrunheira, sala 0M, 2710-089 SINTRA

Fazer uma pergunta (+351) 21 911 2760 pt-info@phoenixcontact.com

EU RoHS
Cumpre os requisitos de substância segundo a Diretiva RoHS	Sim (Sem regras de exceção)
China RoHS
Environment friendly use period (EFUP)	EFUP-E Nenhuma substância perigosa acima dos valores-limite
EU REACH SVHC
Nota sobre as substâncias candidatas ao REACH (n.º CAS)	Nenhuma substância numa proporção superior a 0,1 % em massa

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

ST-5EP1N8AAD00S - Device connector front mounting

1607709

Detalhes dos produtos

ECLASS

ETIM

UNSPSC

cUL Recognized

UL Recognized

UL Listed

cUL Listed

UL Recognized

cUL Recognized

Produtos compatíveis

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

ST-5EP1N8AAD00S - Device connector front mounting 1607709

Detalhes dos produtos

ECLASS

ETIM

UNSPSC

Produtos compatíveis

ST-10KP010 - Crimp contact 1618255

ST-10KP035 - Crimp contact 1618458

PROT-M17PRO-OT-IP20 - Plastic protective cap 1055708

ST-Z0019 - Color coding 1620621

ST-Z0020 - Color coding 1620622

ST-Z0021 - Color coding 1620623

ST-Z0014 - Metal protective cap 1616069

ST-Z0013 - Metal protective cap 1616068

Pesquisado com frequência

ST-5EP1N8AAD00S - Device connector front mounting

1607709