Connector in molded plastic on both sides - K-8E-M23M9/2,0-H00/M23F8-C5-S

Connector in molded plastic on both sides, length: 2 m, color of outer sheath: orange RAL 2003

Detalhes dos produtos

Notes on operation Observe derating curve.
Safety note
Safety note WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
• The products are suitable for applications in plant, controller, and electrical device engineering.
• When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
• Assembled products may not be manipulated or improperly opened.
• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at
• When using the product in direct connection with third-party manufacturers, the user is responsible.
• For operating voltages > 50 V AC, conductive connector housings must be grounded
• Ensure that the protective or functional ground has been properly connected.
• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
• Only use tools recommended by Phoenix Contact
• The installation notes/Design In documents online on the download page at must be observed for this product.
• Operate the connector only when it is fully plugged in and interlocked.
• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
• Observe the minimum bending radius of the cable. Lay the cable without twisting it.
• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).

Product type Signal and power cable

Max. current 26 A

Cable length 2 m

N.º de artigo 1622244
Pcs./Emb 1 Unidade
Quantidade mínima de pedido 2 Unidade
Observação Produção ligada a pedido (sem devolução)
Chave comercial ABR
Chave de produto ABRDME
Página de catálogo Página 226 (C-2-2019)
GTIN 4055626070001
Peso por unidade (inclusive embalagem) 951,5 g
Peso por unidade (excluindo embalagem) 111 g
Número do imposto alfandegário 85444290
País de origem DE


ECLASS-9.0 27060311
ECLASS-10.0.1 27060311
ECLASS-11.0 27060311


ETIM 8.0 EC003569




UL Listed

Approval Specification Data
Tensão nominal UN Corrente nominal IN Secção transversal American Wire Gauge Secção transversal mm2
Power 600 V 16 A
Signal 50 V 4 A
Data 30 V 1 A

cUL Listed

Approval Specification Data
Tensão nominal UN Corrente nominal IN Secção transversal American Wire Gauge Secção transversal mm2
Power 600 V 16 A
Signal 50 V 4 A
Data 30 V 1 A

cULus Listed

REACh SVHC Lead 7439-92-1
China RoHS Environmentally Friendly Use Period = 50 years
For information on hazardous substances, refer to the manufacturer’s declaration available under “Downloads”


Transmission of signals, data, and power in just a single connector
CAT5 data interface for up to 100 Mbps
Our standard: robust halogen-free PUR cable
Simple and safe: 100% electrically tested and assembled ready for use
Designs with pre-assembled cables on one or both sides
Customer-specific assemblies and cable lengths can be supplied