PTCB BE PT 6 - Elemento de base
1567576

Elemento de base, tipo de montagem: Trilho de fixação: TH 35 - 7,5 mm, corrente nominal: 31 A

Este produto necessita de outros produtos para a operação. Acessórios requeridos

Detalhes do produto

Produtos compatíveis

Suas vantagens

Mais espaço no quadro de comando graças à largura de apenas 8 mm
Configurar aplicações facilmente, pois é possível jumpear para a linha de réguas de bornes CLIPLINE complete
Transparência em relação à utilização e ao status do sistema graças às conexões integradas para sinais individuais ou coletivos
Fácil comissionamento e manutenção graças ao cabeamento pré-instalável que permanece intacto ao substituir o plugue

Perguntas frequentes

How does the feed-in work and how is the bridging carried out?

Currents of up to 40 A can be fed in at the upper terminal point. Conductors with up to 6 mm2 flexible or 10 mm2 rigid can be connected. The current fed in can be distributed via the bridge shafts arranged at the top with FBS ..... Ver mais

Currents of up to 40 A can be fed in at the upper terminal point. Conductors with up to 6 mm2 flexible or 10 mm2 rigid can be connected. The current fed in can be distributed via the bridge shafts arranged at the top with FBS ...-8 bridges. The following applies: currents greater than 31 A must be distributed via two bridges; currents up to and including 31 A can be distributed via one bridge.

Ver menos

Which characteristic curves do I select and when?

Two different characteristic curves are available:
- The faster F2 characteristic curve is suitable for more sensitive loads, such as sensors or resistive loads. It triggers at DC voltages in the 4 ... 8 x In range.
- The medium-lag M1 characte... Ver mais

Two different characteristic curves are available:
- The faster F2 characteristic curve is suitable for more sensitive loads, such as sensors or resistive loads. It triggers at DC voltages in the 4 ... 8 x In range.
- The medium-lag M1 characteristic curve is recommended for more current-intensive (e.g. capacitive) loads or motors. It triggers at DC voltages 8 ... 15 times In.

Ver menos

Are there requirements for the PS? What needs to be considered for correct dimensioning?

For selective protection, the power supply should be able to supply the necessary increased tripping current. Line impedances must also be taken into account.

What is meant by short-circuit breaking capacity and what is the difference between the terms Icn and Inc?

Short-circuit breaking capacity: Maximum short-circuit current that the circuit breaker can safely switch off. What must be observed if the source current is higher than the short circuit breaking capacity? In this case, the protective circuit breake... Ver mais

Short-circuit breaking capacity: Maximum short-circuit current that the circuit breaker can safely switch off. What must be observed if the source current is higher than the short circuit breaking capacity? In this case, the protective circuit breaker may be used with a backup fuse up to the Inc. Certain fuses have been tested and approved for this purpose (see certificate).
- Icn (rated short-circuit breaking capacity): Value that the circuit breaker alone can switch off without backup fuse.
- Inc (Conditional rated short-circuit current): Value that the switch can handle with an upstream fuse.

Ver menos

Can the PTCB TM be used for AC and DC?

Yes, for AC the prospective short-circuit current at the intended installation location must be taken into account. This must not exceed the breaking capacity of the PTCB TM. The magnetic tripping for AC and DC differs by the factor DC/AC = 1.3.

Ver FAQ
PHOENIX CONTACT Ind. Com. Ltda.
Avenida das Nações Unidas, 11.541, 19º andar - Cidade Monções - CEP: 04578-000 - São Paulo/SP
Faça uma pergunta. +55 11 3871-6400 (PABX)