Uninterruptible power supply - QUINT4-UPS/1AC/1AC/500VA/USB
1067327

QUINT USV, IQ Technology, DIN rail mounting, input:120 V AC / 230 V AC, output:120 V AC / 230 V AC / 500 VA.

Downloads

Product Details




Input voltage 120 V AC
230 V AC
Input voltage range 90 V AC ... 264 V AC
Nominal input voltage range 100 V AC ... 240 V AC
Typical national grid voltage 120 V AC
Voltage type of supply voltage AC
Frequency range (fN) 45 Hz ... 65 Hz
Permissible backup fuse max. 25 A
Current consumption 6.9 A (100 V AC)
2.86 A (240 V AC)
19 A (24 V DC)
Signal Bat.-Start
Connection labeling 3.6, 3.7
Signalization designation Bat.-Start
Low signal Connection to SGnd with < 2.7 kΩ
High signal Open (> 200 kΩ between Bat.-Start and SGnd)
Signal Remote
Connection labeling 3.8
Signalization designation Remote
Low signal Connection to SGnd with < 2.7 kΩ
High signal Open (> 35 kΩ between Remote and SGnd)

Efficiency > 97 % (100 % load, with charged energy storage)
~ 87 % (100 % load )
Apparent power 500 VA
Real power 400 W
Power factor (cos phi) 0.8
Crest factor 2.8
Switch-over time < 10 ms
UPS classification VFD-SS-311
Connection in parallel no
Connection in series No
Overload capability Battery operation 105 % (Permanent)
120 % ... 150 % (20 s / 5 s, then shutdown)
Mains operation
Output voltage 120 V AC
230 V AC
Nominal output current (IN) 4.17 A (120 V AC)
2.17 A (230 V AC)
Maximum no-load power dissipation typ. 9 W (120 V AC)
typ. 10 W (230 V AC)
Power loss nominal load max. typ. 10 W (120 V AC)
typ. 11 W (230 V AC)
Nominal output frequency 60 Hz ±5 Hz
50 Hz ±5 Hz
Output fuse 10 A 400 V gRL
Battery operation
Output voltage 120 V AC ±2 %
230 V AC ±2 %
Form of output voltage Pure sine
Maximum no-load power dissipation approx. 23 W (120 V AC)
approx. 24 W (230 V AC)
Power loss nominal load max. approx. 57 W (120 V AC)
approx. 54 W (230 V AC)
Nominal output frequency 60 Hz
50 Hz
±5 % (grid-guided)
±0.5 % (self-guided)
Total harmonic distortion factor (THD) < 3 % (linear load)
< 8 % (non-linear load)
Electronic current limitation > 2,5 x IN (> 200 ms)
Signal AC OK
Connection labeling 3.3
Signalization designation AC OK
Type of signaling Green LED
Switching output Transistor output, active
Output voltage 24 V
Continuous load current ≤ 20 mA
LED status indicator green
Signal Alarm
Connection labeling 3.1
Signalization designation Alarm
Type of signaling LED red
Switching output Transistor output, active
Output voltage 24 V
Continuous load current ≤ 20 mA
LED status indicator red
Signal Battery mode
Connection labeling 3.2
Signalization designation Battery mode
Type of signaling Yellow LED
Switching output Transistor output, active
Output voltage 24 V
Continuous load current ≤ 20 mA
LED status indicator yellow
Signal P>Pn
Connection labeling 3.5
Signalization designation P>Pn
Switching output Transistor output, active
Output voltage 24 V
Continuous load current ≤ 20 mA
Signal Ready
Connection labeling 3.4
Signalization designation Ready
Type of signaling Green LED
Switching output Transistor output, active
Output voltage 24 V
Continuous load current ≤ 20 mA
LED status indicator green
Signal ground SGnd
Connection labeling 3.9
Function Signal ground
Reference potential For signal inputs and signal outputs

Input voltage 24 V DC
End-of-charge voltage 24 V DC ... 31 V DC (temperature compensated)
Charge current max. 5 A
Nominal capacity range 3.4 Ah ... 200 Ah (5x 40 Ah)
Deep discharge protection 20 V DC ... 24 V DC (can be parameterized)
Battery technology VRLA, VRLA-WTR, LI-ION (see section: Ordering data)
Charge characteristic curve IU0U

Input
Position 1.x
Conductor connection
Connection method Screw connection
rigid 0.2 mm² ... 6 mm²
flexible 0.2 mm² ... 4 mm²
flexible with ferrule without plastic sleeve 0.2 mm² ... 4 mm²
flexible with ferrule with plastic sleeve 0.2 mm² ... 4 mm²
rigid (AWG) 30 ... 10
Stripping length 8 mm
Torque 0.5 Nm ... 0.6 Nm
Drive form screw head Slotted L
Output
Position 2.x
Conductor connection
Connection method Screw connection
rigid 0.2 mm² ... 6 mm²
flexible 0.2 mm² ... 4 mm²
flexible with ferrule without plastic sleeve 0.2 mm² ... 4 mm²
flexible with ferrule with plastic sleeve 0.2 mm² ... 4 mm²
rigid (AWG) 30 ... 10
Stripping length 8 mm
Torque 0.5 Nm ... 0.6 Nm
Drive form screw head Slotted L
Signal
Position 3.x
Conductor connection
Connection method Screw connection
rigid 0.2 mm² ... 1.5 mm²
flexible 0.2 mm² ... 1.5 mm²
flexible with ferrule without plastic sleeve 0.2 mm² ... 1.5 mm²
flexible with ferrule with plastic sleeve 0.2 mm² ... 1.5 mm²
rigid (AWG) 30 ... 12
Stripping length 8 mm
Torque 0.5 Nm ... 0.6 Nm
Drive form screw head Slotted L
Battery
Position 4.x
Conductor connection
Connection method Screw connection
rigid 0.2 mm² ... 6 mm²
flexible 0.2 mm² ... 4 mm²
flexible with ferrule without plastic sleeve 0.2 mm² ... 4 mm²
flexible with ferrule with plastic sleeve 0.2 mm² ... 4 mm²
rigid (AWG) 30 ... 10
Stripping length 8 mm
Torque 0.5 Nm ... 0.6 Nm
Drive form screw head Slotted L

Interface USB (Modbus/RTU)
Number of interfaces 1
Connection method MINI-USB Type B
Connection marking 5.1
Locking Screw
Transmission physics USB 2.0
Maximum cable length 3 m
Electrical isolation yes

Number of phases 1.00

Product type Uninterruptible power supply, AC
MTBF (IEC 61709, SN 29500) 445469 h (40 °C)
Insulation characteristics
Protection class I
Overvoltage category II

Width 180 mm
Height 130 mm
Depth 125 mm
Installation dimensions
Installation distance right/left 0 mm / 0 mm
Installation distance top/bottom 50 mm / 50 mm

Mounting type DIN rail mounting

Housing material Metal

Ambient conditions
Degree of protection IP20
Ambient temperature (operation) -25 °C ... 60 °C (> 50 °C: 2,5 % / K)
Ambient temperature (storage/transport) -40 °C ... 85 °C
Maximum altitude ≤ 3000 m (> 2000 m: 0,6 % / 100 m)
Max. permissible relative humidity (operation) ≤ 95 %
Shock 20g in all directions (EN 60068-2-27)
Vibration (operation) 5 Hz ... 100 Hz, 0.7g (EN 60068-2-6)

Uninterruptible power supply systems
Standards/specifications EN 62040-1

UL
Identification UL/C-UL Recognized UL 1778

Low Voltage Directive Conformance with Low Voltage Directive 2014/35/EC
Electromagnetic compatibility Conformance with EMC Directive 2014/30/EU
Conducted noise emission EN 62040-02 (Class C2)
Interference emission Noise emission in accordance with EN 62040-2
Noise immunity Immunity in accordance with EN 62040-2
Electrostatic discharge
Standards/regulations EN 61000-4-2
Electrostatic discharge
Contact discharge ± 6 kV
Discharge in air ± 8 kV
Comments Criterion A
Electromagnetic HF field
Standards/regulations EN 61000-4-3
Electromagnetic HF field
Frequency range 80 MHz ... 6 GHz
Test field strength 10 V/m
Comments Criterion A
Fast transients (burst)
Standards/regulations EN 61000-4-4
Fast transients (burst)
Input ± 2 kV
± 2 kV
Output ± 2 kV
Signal ± 2 kV
± 2 kV (USB)
Comments Criterion A (B for USB)
Surge voltage load (surge)
Standards/regulations EN 61000-4-5
Signal 1 kV (asymmetrical)
Comments Criterion A
Input/Output ± 1 kV (symmetrical)
± 2 kV (asymmetrical)
Conducted interference
Standards/regulations EN 61000-4-6
Conducted interference
Frequency range 0.15 MHz ... 80 MHz
Signal 1 kV (asymmetrical)
Comments Criterion A
Power frequency magnetic field
Standards/regulations EN 61000-4-8
Frequency 50 Hz
Signal 30 A/m
Comments Criterion A
Criterion A Normal operating behavior within the specified limits.
Criterion B Temporary impairment to operational behavior that is corrected by the device itself.

Item number 1067327
Packing unit 1 pc
Minimum order quantity 1 pc
Product Key CMUI15
GTIN 4055626736082
Weight per Piece (including packing) 3,062 g
Weight per Piece (excluding packing) 2,490 g
Customs tariff number 85044090
Country of origin DE


ECLASS

ECLASS-9.0 27040705
ECLASS-11.0 27040705

ETIM

ETIM 8.0 EC000382

UNSPSC

UNSPSC 21.0 39121000

IECEE CB Scheme

Approval ID: DK-95944-UL

cULus Recognized

Approval ID: FILE E 342453

EAC

Approval ID: RU-DE.B.00184/20

UL Recognized

Approval ID: FILE E 359066

REACh SVHC Lead 7439-92-1
China RoHS Environmentally Friendly Use Period = 50 years
For information on hazardous substances, refer to the manufacturer’s declaration available under “Downloads”