PLC-BPT-12DC/1/SSI - Relay base - 1094757

Notes on operation	Do not connect adjacent channels to SELV/ PELV and voltages dangerous to the touch.
Notes on operation	The outputs are not suitable for switching different outer conductors with appropriate switching output (applies to the AC optocoupler variants and relays).
Notes on operation	The system installer must ensure the touch protection of the product (at voltages > 25 V AC/60 V DC). The product is a built-in device without protection against direct contact.
Notes on operation	At least one functional insulation against adjacent modules is complied with in the support rail direction. If the application has higher requirements on the insulation (basic or reinforced insulation), then these must be realized through suitable measures (e. g., partition plates).
Notes on operation	Do not use to separate SELV/PELV circuits from other circuits, because safe isolation is not guaranteed. (applies to the optocoupler variants)

Product type	Relay socket
Product family	PLC-INTERFACE
Operating mode	100% operating factor
Insulation characteristics: Air clearances and creepage distances between the power circuits
Insulation	Safe isolation, reinforced insulation
Overvoltage category	III
Pollution degree	2

Air clearances and creepage distances between the power circuits
Rated insulation voltage	250 V AC
Rated surge voltage	6 kV

Nominal input voltage U_N	12 V DC
Input voltage range in reference to U_N	0.8 ... 1.2
Nominal input voltage U_N	12 V DC
Relay assembly
Rated control circuit supply voltage U_S	24 V DC
Voltage range with reference to U_S	0.8 ... 1.2
Rated control supply current I_S	9 mA
Rated actuating current I_C	1 mA
Typical response time	5 ms
Typical release time	7 ms
Protective circuit	Reverse polarity protection
	Surge protection
Surge voltage protection	> 33 V
Optocoupler assembly
Rated control circuit supply voltage U_S	24 V DC
Voltage range with reference to U_S	0.8 ... 1.2
Rated control supply current I_S	≥ 8 mA (depends on type)

Maximum switching voltage	48 V DC
Minimum switching voltage	3 V DC
Limiting continuous current	100 mA
Voltage drop at max. limiting continuous current	< 1 V
Output circuit	2-conductor, floating
Protective circuit	Reverse polarity protection
Protective circuit		Surge protection
Maximum switching voltage	33 V DC
Minimum switching voltage	3 V DC
Limiting continuous current	3 A
Voltage drop at max. limiting continuous current	< 200 mV
Output circuit	2-conductor, floating
Protective circuit	Reverse polarity protection
Protective circuit		Surge protection
Maximum switching voltage	253 V AC (Partition plate PLC-ATP must be installed for voltages larger than 250 V (L1, L2, L3) between identical terminal points in adjacent modules. Potential bridging is then carried out with FBST 8-PLC... or ...FBST 500...)
Minimum switching voltage	24 V AC
Limiting continuous current	0.75 A
Voltage drop at max. limiting continuous current	< 1 V
Maximum inrush current	30 A (10 ms)
Output circuit	2-conductor, floating
Protective circuit	RCV circuit
Protective circuit		Surge protection
Leakage current	< 1 mA
Max. load value	4.5 A²s

Connection method	Push-in connection
Stripping length	10 mm
Conductor cross-section rigid	0.14 mm² ... 2.5 mm²
Conductor cross-section flexible	0.14 mm² ... 2.5 mm²
		0.2 mm² ... 2.5 mm² (Single ferrule)
		2x 0.5 mm² ... 1 mm² (TWIN ferrule)
Conductor cross-section AWG	26 ... 14

Width	6.2 mm
Height	80 mm
Depth	94 mm

Ambient conditions
Degree of protection	IP20
Ambient temperature (operation)	-25 °C ... 60 °C
Ambient temperature (storage/transport)	-40 °C ... 85 °C
Altitude	≤ 2000 m

Corrosive gas test
Identification	ISA-S71.04. G3 Harsh Group
		EN 60068-2-60

Mounting type	DIN rail mounting
Assembly note	in rows with zero spacing
Mounting position	any

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

PLC-BPT-12DC/1/SSI - Relay base

1094757

Product details

ETIM

UNSPSC

Compatible products

Air clearances and creepage distances between the power circuits
Standards/regulations	DIN EN 50178

Item number	1094757
Packing unit	10 pc
Minimum order quantity	1 pc
Note	Made to order (non-returnable)
Product key	DK6231
GTIN	4055626918884
Weight per piece (including packing)	32.12 g
Weight per piece (excluding packing)	32.12 g
Customs tariff number	85366990
Country of origin	DE

EU RoHS
Fulfills EU RoHS substance requirements	Yes
Exemption	7(a), 7(c)-I
China RoHS
Environment friendly use period (EFUP)	EFUP-50 An article-related China RoHS declaration table can be found in the download area for the respective article under "Manufacturer declaration". For all articles with EFUP-E, no China RoHS declaration table issued and required.
EU REACH SVHC
REACH candidate substance (CAS No.)	Lead (CAS: 7439-92-1)
SCIP	d3090d0a-8866-4865-a93d-dac9f0792eee

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

PLC-BPT-12DC/1/SSI - Relay base 1094757

Product details

ETIM

UNSPSC

Compatible products

REL-MR- 24DC/21 - Single relay 2961105

REL-MR- 24DC/21AU - Single relay 2961121

REL-MR- 24DC/21/MS - Single relay 2909642

OPT-24DC/ 48DC/100 - Miniature solid-state relay 2966618

OPT-24DC/ 24DC/ 2 - Miniature solid-state relay 2966595

OPT-24DC/230AC/ 1 - Miniature solid-state relay 2967950

FBST 500-PLC RD - Continuous plug-in bridge 2966786

FBST 500-PLC BU - Continuous plug-in bridge 2966692

FBST 500-PLC GY - Continuous plug-in bridge 2966838

FBST 6-PLC RD - Single plug-in bridge 2966236

FBST 6-PLC BU - Single plug-in bridge 2966812

FBST 6-PLC GY - Single plug-in bridge 2966825

FBST 8-PLC GY - Single plug-in bridge 2967688

PLC-ATP BK - Separating plate 2966841

PLC-ESK GY - Power terminal block 2966508

SZF 1-0,6X3,5 - Screwdriver 1204517

ZB 6:UNBEDRUCKT - Zack marker strip 1051003

ZB 6 CUS - Zack marker strip 0824992

ZB 6,LGS:FORTL.ZAHLEN - Zack marker strip 1051016

ZB 6,QR:FORTL.ZAHLEN - Zack marker strip 1051029

ZB 6,LGS:GLEICHE ZAHLEN - Zack marker strip 1051032

ZB 6,LGS:L1-N,PE - Marker for terminal blocks 1051414

ZB 6,LGS:U-N - Marker for terminal blocks 1051430

UC-TM 6 - Marker for terminal blocks 0818085

UC-TM 6 CUS - Marker for terminal blocks 0824589

UCT-TM 6 - Marker for terminal blocks 0828736

UCT-TM 6 CUS - Marker for terminal blocks 0829602

NS 35/ 7,5 PERF 2000MM - DIN rail perforated 0801733

NS 35/ 7,5 UNPERF 2000MM - DIN rail, unperforated 0801681

NS 35/ 7,5 WH PERF 2000MM - DIN rail perforated 1204119

NS 35/ 7,5 WH UNPERF 2000MM-VPE 10 - DIN rail, unperforated 1204122

NS 35/ 7,5 AL UNPERF 2000MM - DIN rail, unperforated 0801704

NS 35/ 7,5 ZN PERF 2000MM - DIN rail perforated 1206421

NS 35/ 7,5 ZN UNPERF 2000MM - DIN rail, unperforated 1206434

NS 35/ 7,5 CU UNPERF 2000MM-VPE 10 - DIN rail, unperforated 0801762

NS 35/ 7,5 CAP - End cap 1206560

NS 35/15 PERF 2000MM - DIN rail perforated 1201730

NS 35/15 UNPERF 2000MM - DIN rail, unperforated 1201714

NS 35/15 WH PERF 2000MM - DIN rail perforated 0806602

NS 35/15 WH UNPERF 2000MM-VPE 10 - DIN rail, unperforated 1204135

NS 35/15 AL UNPERF 2000MM - DIN rail, unperforated 1201756

NS 35/15 ZN PERF 2000MM - DIN rail perforated 1206599

NS 35/15 ZN UNPERF 2000MM - DIN rail, unperforated 1206586

NS 35/15 CU UNPERF 2000MM-VPE 10 - DIN rail, unperforated 1201895

NS 35/15 CAP - End cap 1206573

NS 35/15-2,3 UNPERF 2000MM-VPE 10 - DIN rail, unperforated 1201798

PLC-BPT-12DC/1/SSI - Relay base

1094757