The intelligent Lumgate luminaire control unit is used to couple a light management system to tunnel luminaires. The luminaires are switched, dimmed, and monitored via DALI, analog interface, and load relays. Suitable for installation in driver boxes or directly in the luminaire.
LUMGATE 277 2DOR/1AO DALI
-
Interface
1274016
Luminaire control unit for controlling LED drivers, 110 V ... 277 V input voltage, 2 relay outputs, 8 A load current, up to 8 LED drivers can be controlled, 10 V analog interface, DALI interface, measurement of load currents
Product Details
| Dimensional drawing |
|
| Width | 124 mm |
| Height | 79 mm |
| Depth | 30 mm |
| Remote bus | |
| Transmission speed | 500 kBaud |
| DALI | |
| No. of channels | 1 |
| Fieldbus: DALI | |
| Designation | DALI |
| Output current | 28 mA (guaranteed, max. 14 DALI devices) |
| max. 40 mA | |
| Type of protection | Overload protection |
| Module | |
| ID code (dec.) | 51 |
| ID code (hex) | 33 |
| Input address area | 16 bit |
| Output address area | 16 bit |
| Analog | |
| Output name | Analog voltage output |
| Number of outputs | 1 |
| D/A converter resolution | 8 bit |
| Current output signal | max. -20 mA (Current sink) |
| Voltage output signal | 1 V ... 10 V |
| Permissible cable length | max. 0.5 m |
| Digital | |
| Output name | Relay output |
| Number of outputs | 2 |
| Output voltage | 250 V AC (Soft start function to reduce the inrush current of the LED drivers, not suitable for inductive loads) |
| Output current | max. 8 A (max. 5 A per relay, resistive load for applications with UL/CSA approval) |
| Nominal output voltage | max. 277 V AC (50 Hz ... 60 Hz) |
| Type | Stand-Alone |
| Product type | I/O component |
| Diagnostics messages | Bus error in INTERBUS |
| Insulation characteristics | |
| Overvoltage category | III |
| Pollution degree | 2 |
| Supply: | |
| Designation | Device supply |
| Supply voltage | max. 250 V AC (Class II / EN 61347) |
| Supply voltage range | 110 V AC ... 277 V AC -13 % ... +6 % |
| Current consumption | max. 8 A (with active consumers) |
| Connection technology | |
| Connection name | Supply |
| Note on the connection method | Use copper wire, that is approved up to 85°C. |
| Conductor connection | |
| Connection method | Push-in spring connection |
| Conductor cross section rigid | 0.34 mm² ... 4 mm² |
| Conductor cross section flexible | 0.2 mm² ... 2.5 mm² |
| Conductor cross section AWG | 24 ... 12 |
| Stripping length | 10 mm |
| Supply | |
| Connection method | Push-in spring connection |
| Note on the connection method | Use copper wire, that is approved up to 85°C. |
| Conductor cross section, rigid | 0.34 mm² ... 4 mm² |
| Conductor cross section, flexible | 0.2 mm² ... 2.5 mm² |
| Conductor cross section AWG | 24 ... 12 |
| Stripping length | 10 mm |
| INTERBUS | |
| Connection method | Push-in spring connection |
| Note on the connection method | pluggable |
| Conductor cross section, rigid | 0.2 mm² ... 1.5 mm² |
| Conductor cross section, flexible | 0.2 mm² ... 1.5 mm² |
| Conductor cross section AWG | 24 ... 16 |
| Stripping length | 10 mm |
| DALI and analog output | |
| Connection method | Push-in spring connection |
| Note on the connection method | pluggable |
| Conductor cross section, rigid | 0.2 mm² ... 1.5 mm² |
| Conductor cross section, flexible | 0.2 mm² ... 1.5 mm² |
| Conductor cross section AWG | 24 ... 16 |
| Stripping length | 10 mm |
| Relay output | |
| Connection method | Push-in spring connection |
| Conductor cross section, rigid | 0.34 mm² ... 4 mm² |
| Conductor cross section, flexible | 0.2 mm² ... 2.5 mm² |
| Conductor cross section AWG | 24 ... 12 |
| Stripping length | 10 mm |
| Ambient conditions | |
| Ambient temperature (operation) | -40 °C ... 65 °C |
| Degree of protection | IP20 (touch-proof (per manufacturer's declaration)) |
| Air pressure (operation) | 70 kPa ... 106 kPa (up to 3000 m above sea level) |
| Air pressure (storage/transport) | 70 hPa ... 106 kPa (up to 3000 m above sea level) |
| Ambient temperature (storage/transport) | -40 °C ... 85 °C |
| Permissible humidity (operation) | 5 % ... 95 % (up to 45°C in accordance with EN 60068-2-78:2013) |
| Permissible humidity (storage/transport) | 5 % ... 90 % (according to DIN EN 61131-2, non-condensing, no ice formation) |
| Mounting type | Mounting in enclosure (control box) |
cUL Listed
Approval ID: FILE E 238705Your advantages
Easy integration into existing light fittings
Failsafe behavior in the event of faulty communication (freely definable substitute values)
Up to 8 DALI ballasts can be connected in accordance with IEC 62386
2 relay outputs with soft start function to reduce the inrush current of the LED drivers