• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
• The products are suitable for applications in plant, controller, and electrical device engineering.
• Assembled products may not be manipulated or improperly opened.
• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
• When using the product in direct connection with third-party manufacturers, the user is responsible.
• For operating voltages > 50 V AC, conductive connector housings must be grounded
• Ensure that the protective or functional ground has been properly connected.
• Observe the corresponding technical data. You will find information: o On the product o On the packing label o In the supplied documentation o Online at phoenixcontact.com/products under the product
• The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product.
• Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products
• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).
• Operate the connector only when it is fully plugged in and interlocked.
• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
• Observe the minimum bending radius of the cable. Lay the cable without twisting it.
Product family
SUNCLIX
Number of positions
1
Insulation characteristics
Protection class
II
Degree of pollution
2
Rated voltage (III/2)
1500 V
Nominal voltage ATD
1500 V DC (II/2.00) in accordance with IEC 62852:2014/AMD1:2020
Rated surge voltage
16 kV
Rated current (16 mm²)
60 A (in accordance with IEC 62852:2014-11)
Rated current (10 mm²)
50 A (in accordance with IEC 62852:2014-11)
Rated current (6.0 mm²)
40 A (in accordance with IEC 62852:2014-11)
Contact resistance
≤ 0.45 mΩ (when plugged in (without cable))
Connection method
Spring-cage
Width
23.7 mm
Height
23.7 mm
Length
83.4 mm
Color
black
Color of the housing part
black
Material Housing
PPE
Material Seal
EPDM
Material Cable gland
PPE
Material Contact
Cu
Material Contact carrier
PPE
Flammability rating according to UL 94
V0
Insulating material group
I / CTI 600
Contact surface material
Ni/Ag
O-ring material
Silopren
External cable diameter
5.5 mm ... 10 mm
Single wire, cross section
6 mm² 16 mm² 10 AWG 6 AWG
Stripping length of the individual wire
18 mm
Outside conductor diameter
10.00 mm 5.50 mm
Mechanical data
Outside conductor diameter
10.00 mm 5.50 mm
Insertion/withdrawal cycles
100
Insertion force
45 N ±10 N
Withdrawal force
250 N ±50 N (when locked)
Ambient conditions
Degree of protection (when plugged in)
IP66/IP68 (2 m / 2 h)
Degree of protection (not plugged in)
IP20
Ambient temperature (operation)
-40 °C ... 85 °C (dependent on the derating curve)
