1. Home
  2. Products
  3. Connectors and cables
  4. Installation connectors and installation cables
  5. Contact carriers - PRC 5-HEAD-MS6-2
Connector pin assignment

Contact carriers - PRC 5-HEAD-MS6-2
1070199

Contact insert, Range of articles: PRC 35, Contact carriers, housing material: PPE, color: black, number of positions: 5, min. conductor cross section: 1.5 mm2, max. conductor cross section: 6 mm2, rated voltage: 690 V AC, rated current: 35 A, Connection method: Screw connection, Type of contact: Pin. Contact insert without connector housing. Please order the appropriate connector housings according to the accessories list.

Product Details

Order information: Contact insert without connector housing. Please order the appropriate connector housings according to the accessories list.
Safety note
Safety note • WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
• Assembled products may not be manipulated or improperly opened.
• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
• When using the product in direct connection with third-party manufacturers, the user is responsible.
• For operating voltages > 50 V AC, conductive connector housings must be grounded
• Ensure that the protective or functional ground has been properly connected.
• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
• Observe the corresponding technical data. You will find information:
o On the product
o On the packing label
o In the supplied documentation
o Online at phoenixcontact.com/products under the product
• Only use tools recommended by Phoenix Contact
• The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product.
• Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products
• Operate the connector only when it is fully plugged in.
• Operate the connector only when it is fully plugged in and interlocked.
• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
• Observe the minimum bending radius of the cable. Lay the cable without twisting it.
• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).
Product type Contact insert
Number of positions 5
Connection profile 4+PE
Locking type Snap-in locking
Insulation characteristics
Protection class II
Degree of pollution 2
Rated voltage (III/2) 690 V
Nominal voltage ATD 690 V AC in accordance with IEC 61984
600 V AC In accordance with UL 2238
500 V DC in accordance with IEC 61535, when mounted
Rated surge voltage (III/2) 8 kV
Rated current 35 A (With 6 mm² conductor cross section in accordance with IEC 61984)
32 A (With 6 mm² conductor cross section in accordance with IEC 61535)
21.4 A (With 6 mm² conductor cross section and 85 °C in accordance with 2 PfG 1915)
35 A (with AWG 10, in accordance with UL 2237)
Width 35.9 mm
Height 34.5 mm
Length 48.4 mm
Color black
Color of the housing part black
Flammability rating according to UL 94 V0
Insulating material group I / CTI 600
Seal material EPDM
Contact material Cu alloy
Contact surface material silver-plated
Contact carrier material PPE
O-ring material EPDM
Housing material PPE
Insertion/withdrawal cycles 2000
Cable structure
Single wire, cross section 1.5 mm² 6 mm²
Stripping length of the individual wire Lay PE conductor 8 mm leading
Ambient conditions
Degree of protection IP66 / IP68 (2m / 24h) / IP69K
Degree of protection IP66 / IP68 (2m / 24h) / IP69K
Ambient temperature (operation) -40 °C ... 105 °C (dependent on the derating curve)
Ambient temperature (storage/transport) -40 °C ... 70 °C
Ambient temperature (assembly) -5 °C ... 85 °C
Item number 1070199
Packing unit 1 pc
Minimum order quantity 1 pc
Sales Key A16
Product Key ABLCBA
GTIN 4055626748160
Weight per Piece (including packing) 50 g
Weight per Piece (excluding packing) 50 g
Customs tariff number 85366990
Country of origin PL

ECLASS

ECLASS-9.0 27440103
ECLASS-10.0.1 27440109
ECLASS-11.0 27440109

ETIM

ETIM 8.0 EC003569

UNSPSC

UNSPSC 21.0 39121400

cUL Recognized

Approval ID: E468743-20200116

UL Recognized

Approval ID: E468743-20200116

EAC

Approval ID: B.01687

VDE Zeichengenehmigung

Approval ID: 40054231
Approval Specification Data
Nominal Voltage UN Nominal Current IN Cross Section AWG Cross Section mm2
690 V 35 A

VDE Zeichengenehmigung

Approval ID: 40054228
Approval Specification Data
Nominal Voltage UN Nominal Current IN Cross Section AWG Cross Section mm2
500 V 32 A

cULus Recognized

China RoHS Environmentally friendly use period: unlimited = EFUP-e
No hazardous substances above threshold values

Compatible Products

Your advantages

Versatile interfaces with straight and angled connector housings
Universal accommodation of existing connector heads with screw connection technology
Modular system for optimized storage
Locking mechanism can be unlocked manually or using a tool
Ideal for indoor and outdoor use due to weatherproof materials