Cable connector - M23-17S1N8A8003
1629206

Cable connector, M23 PRO, straight, shielded: yes, Screw locking, M23, No. of pos.: 17, Direction of rotation: Standard, type of contact: Socket, Crimp connection, cable diameter range: 6 mm ... 10 mm, coding:N


Product Details




Order information: Order 17 x 1 mm crimp contacts separately
Safety note
Safety note WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
• The products are suitable for applications in plant, controller, and electrical device engineering.
• When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
• Assembled products may not be manipulated or improperly opened.
• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
• When using the product in direct connection with third-party manufacturers, the user is responsible.
• For operating voltages > 50 V AC, conductive connector housings must be grounded
• Ensure that the protective or functional ground has been properly connected.
• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
• Only use tools recommended by Phoenix Contact
• The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product.
• Operate the connector only when it is fully plugged in and interlocked.
• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
• Observe the minimum bending radius of the cable. Lay the cable without twisting it.
• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).

Product type Circular connector (cable-side)

Ambient temperature (operation) -40 °C ... 105 °C (see to derating)
Permanent temperature 125 °C (DIN EN 60512-9-2 / 1000 h)

Connection 1
Head design Socket
Insulating body
Note Order information: Order crimp contacts Ø 1 mm separately
Coding N
Insulation body material PA 6.6
Insertion/withdrawal cycles 100
Connection method Crimp connection
Contact type Socket
Application Signal
Number of positions 17
Direction of rotation Standard
Connection profile 17
Contact diameter Signal contacts 1 mm
Litz wire cross-section Signal contacts min. 0.08 mm²
Litz wire cross-section Signal contacts max. 1 mm²
Nominal current per signal contact 8 A
Note for max. connection cross section
Rated voltage Signal contact 125 V
Rated surge voltage 2 kV
Overvoltage category III
Degree of pollution 3
Installation height 2000 m
Housing
Housing material GD-Zn
Type of locking Screw locking
Pg screw connection none
Degree of protection (plugged in) IP66 / IP68 (2m / 24h) / IP69K
Thread type M23
Seal
External cable diameter 6 mm ... 10 mm
Seal material FKM

Item number 1629206
Packing unit 1 pc
Minimum order quantity 1 pc
Sales Key A12
Product Key ABRBHA
Catalog Page Page 76 (C-2-2019)
GTIN 4055626618395
Weight per Piece (including packing) 117.4 g
Weight per Piece (excluding packing) 106.5 g
Customs tariff number 85366990
Country of origin DE


ECLASS

ECLASS-9.0 27440102
ECLASS-10.0.1 27440102
ECLASS-11.0 27440102

ETIM

ETIM 8.0 EC002635

UNSPSC

UNSPSC 21.0 39121400

cUL Recognized

Approval ID: E335019-20141210
Approval Specification Data
Nominal Voltage UN Nominal Current IN Cross Section AWG Cross Section mm2
150 V 3.5 A - 20

UL Recognized

Approval ID: E335019-20141210
Approval Specification Data
Nominal Voltage UN Nominal Current IN Cross Section AWG Cross Section mm2
150 V 4.5 A - 20

cULus Recognized


China RoHS Environmentally friendly use period: unlimited = EFUP-e
No hazardous substances above threshold values

Your advantages

Solutions with cross-manufacturer compatibility for standard and fast locking systems
Reliable under the harshest conditions: cable connectors with vibration brake
Modern, consistent design for highly convenient operation
Easy, cost-effective cable assembly: uniform shielding of M17 to M40