VC-K4/5M-SET-M25 - Connector component - 1607994

Notes

Safety note
Safety note	WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
		• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
		• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
		• The products are suitable for applications in plant, controller, and electrical device engineering.
		• When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
		• Assembled products may not be manipulated or improperly opened.
		• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
		• When using the product in direct connection with third-party manufacturers, the user is responsible.
		• For operating voltages > 50 V AC, conductive connector housings must be grounded
		• Ensure that the protective or functional ground has been properly connected.
		• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
		• Observe the corresponding technical data. You will find information: o On the product o On the packing label o In the supplied documentation o Online at phoenixcontact.com/products under the product
		• Only use tools recommended by Phoenix Contact
		• The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product.
		• Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products
		• Operate the connector only when it is fully plugged in.
		• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
		• Observe the minimum bending radius of the cable. Lay the cable without twisting it.
		• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).

Product properties

Type	VC4
No. of cable outlets	1
Type of the screw connection	M25
Fixing screws	M4
Cable outlet	slanted
Insulation characteristics
Degree of pollution	3

Dimensions

Width	33 mm
Height	111 mm
Length	76 mm

Material specifications

Color	gray
Color of the housing part	gray
Flammability rating according to UL 94	V0
Insulating material group	I
Seal material	EPDM
Housing material	PA 6.6
O-ring material	NBR
Material of locking screw	Brass, nickel-plated

Mechanical properties

Mechanical data
Type of the screw connection	M25
Locking type	Screw

Environmental and real-life conditions

Ambient conditions
Degree of protection	IP66
	IP66
Ambient temperature (operation)	-40 °C ... 80 °C

Mounting

Item number	1607994
Packing unit	10 pc
Minimum order quantity	1 pc
Note	Made to order (non-returnable)
Product key	ABLADD
GTIN	4046356116084
Weight per piece (including packing)	500 g
Weight per piece (excluding packing)	500 g
Country of origin	PL

China RoHS
Environment friendly use period (EFUP)	EFUP-E No hazardous substances above the limits
EU REACH SVHC
REACH candidate substance (CAS No.)	No substance above 0.1 wt%

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

VC-K4/5M-SET-M25 - Connector component

1607994

Product details

ECLASS

ETIM

UNSPSC

Compatible products

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

VC-K4/5M-SET-M25 - Connector component 1607994

Product details

ECLASS

ETIM

UNSPSC

Compatible products

VC-K4/5M-SET-M25 - Connector component

1607994