CK2,0-ED-1,0ST AU WTN - Crimp contact - 1445075

Notes

Safety note
Safety note	WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
		• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
		• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
		• The products are suitable for applications in plant, controller, and electrical device engineering.
		• When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
		• Assembled products may not be manipulated or improperly opened.
		• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
		• When using the product in direct connection with third-party manufacturers, the user is responsible.
		• For operating voltages > 50 V AC, conductive connector housings must be grounded
		• Ensure that the protective or functional ground has been properly connected.
		• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
		• Observe the corresponding technical data. You will find information: o On the product o On the packing label o In the supplied documentation o Online at phoenixcontact.com/products under the product
		• Only use tools recommended by Phoenix Contact
		• The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product.
		• Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products
		• Operate the connector only when it is fully plugged in.
		• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
		• Observe the minimum bending radius of the cable. Lay the cable without twisting it.
		• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).

Product properties

Product type	Crimp contact
Series	VARIOCON
Contact material type	turned

Connection data

Connection technology
Contact connection type	Pin
Connection method	Crimp connection

Material specifications

Material Contact	Cu
Material Contact surface	Au

Dimensions

Width [w]	3.9 mm
Height [h]	3.9 mm
Length [l]	19.8 mm

Mechanical properties

Mechanical data
Insertion/withdrawal cycles	100

Environmental and real-life conditions

Item number	1445075
Packing unit	1,000 pc
Minimum order quantity	1,000 pc
Note	Made to order (non-returnable)
Product key	ABLADE
GTIN	4046356581240
Weight per piece (including packing)	0.785 g
Weight per piece (excluding packing)	0.772 g
Country of origin	DE

ECLASS-13.0	27440204
ECLASS-15.0	27440204

EU RoHS
Fulfills EU RoHS substance requirements	Yes
Exemption	6(c)
China RoHS
Environment friendly use period (EFUP)	EFUP-50 An article-related China RoHS declaration table can be found in the download area for the respective article under "Manufacturer declaration". For all articles with EFUP-E, no China RoHS declaration table issued and required.
EU REACH SVHC
REACH candidate substance (CAS No.)	Lead (CAS: 7439-92-1)
SCIP	b34a31b5-a517-41fa-b2cc-3530b7508c46

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

CK2,0-ED-1,0ST AU WTN - Crimp contact

1445075

Product details

ECLASS

ETIM

UNSPSC

Compatible products

Ambient conditions
Ambient temperature (operation)	-40 °C ... 125 °C

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

CK2,0-ED-1,0ST AU WTN - Crimp contact 1445075

Product details

ECLASS

ETIM

UNSPSC

Compatible products

CK2,0-ED-1,0ST AU WTN - Crimp contact

1445075