SH-Z0004 - Contact insert - 1008366

Notes

Safety note
Safety note	WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
		• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
		• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
		• The products are suitable for applications in plant, controller, and electrical device engineering.
		• When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
		• Assembled products may not be manipulated or improperly opened.
		• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
		• When using the product in direct connection with third-party manufacturers, the user is responsible.
		• For operating voltages > 50 V AC, conductive connector housings must be grounded
		• Ensure that the protective or functional ground has been properly connected.
		• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
		• Only use tools recommended by Phoenix Contact
		• The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product.
		• Operate the connector only when it is fully plugged in and interlocked.
		• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
		• Observe the minimum bending radius of the cable. Lay the cable without twisting it.
		• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).

Product properties

Product type	Contact insert
Series	SH
Application	Hybrid
Number of positions	6
Connection profile	6
Thread type	M23

Electrical properties

Contact: Contact group 1
Contact diameter	2 mm
Min. cross section	0.25 mm²
Max. cross section	4 mm²
Nominal current I_N	30 A (for max. connection cross section)
Nominal voltage U_N	630 V AC (Overvoltage category III/3)
Nominal voltage U_N		850 V DC (Overvoltage category II/3)
Overvoltage category	III
Degree of pollution	3
Rated surge voltage	6 kV
Contact: Contact group 2
Contact diameter	0.6 mm
Min. cross section	0.14 mm²
Max. cross section	0.34 mm²
Nominal current I_N	3.6 A (for max. connection cross section)
Nominal voltage U_N	50 V
Overvoltage category	III
Degree of pollution	3
Rated surge voltage	0.8 kV
Contact: Contact group 3
Contact diameter	1 mm
Min. cross section	0.06 mm²
Max. cross section	1 mm²
Nominal current I_N	8 A
Nominal voltage U_N	50 V AC/DC
Overvoltage category	III
Degree of pollution	3
Rated surge voltage	1.5 kV

Connection data

Connection method	Crimp connection

Environmental and real-life conditions

Item number	1008366
Packing unit	100 pc
Minimum order quantity	300 pc
Product key	ABRCDT
GTIN	4055626691084
Weight per piece (including packing)	0.279 g
Weight per piece (excluding packing)	0.265 g
Country of origin	DE

EU RoHS
Fulfills EU RoHS substance requirements	Yes (No exemptions)
China RoHS
Environment friendly use period (EFUP)	EFUP-E No hazardous substances above the limits
EU REACH SVHC
REACH candidate substance (CAS No.)	No substance above 0.1 wt%

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

SH-Z0004 - Contact insert

1008366

Product details

ECLASS

UNSPSC

Compatible products

Ambient conditions
Ambient temperature (operation)	-40 °C ... 115 °C

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

SH-Z0004 - Contact insert 1008366

Product details

ECLASS

UNSPSC

Compatible products

SH-Z0004 - Contact insert

1008366