AXL F PSAI8 I 1F
-
Safety module
1061424
Axioline F, Analog input module, Functional safety, PROFIsafe, Only for connection to Phoenix Contact or Siemens controllers in PROFINET systems, Safe analog inputs: 8 (1-channel assignment), 4 (2-channel assignment), 4 mA ... 20 mA, connection technology: 2-conductor (shielded, twisted pair), degree of protection: IP20
Free download available.
Downloads
Product details
| Dimensional drawing |
|
| Width | 53.6 mm |
| Height | 126.1 mm |
| Depth | 54 mm |
| Note on dimensions | Housing dimensions |
| Note on application | |
| Note on application | Only for industrial use |
| Module | |
| Input address area | 22 Byte (PROFIsafe 2.6.1) |
| Output address area | 5 Byte (PROFIsafe 2.6.1) |
| Required configuration data | 31 Byte |
| Analog: | |
| Input name | Safe analog inputs |
| Number of inputs | 8 (1-channel assignment) |
| 4 (2-channel assignment) | |
| A/D converter resolution | 16 bit |
| Connection method | Push-in connection |
| Connection technology | 2-conductor (shielded, twisted pair) |
| Current input signal | 4 mA ... 20 mA |
| Input resistance current input | typ. 104 Ω |
| Data formats | Standardized representation |
| Input filter | 30 Hz |
| Filtering | RFI filtering / passive TP 1st order |
| Limit frequency (3 dB) | 30 Hz |
| Measured value representation | 16 bits |
| Protective circuit | Transient protection of inputs; Suppressor diode |
| Overload protection; No; ±5.2 V DC, maximum, Imax = 50 mA | |
| Product type | I/O component |
| Product family | Axioline F |
| Application | Functional safety |
| PROFIsafe | |
| Only for connection to Phoenix Contact or Siemens controllers in PROFINET systems | |
| Type | modular |
| Mounting position | any |
| Operating mode | PROFIsafe 2.6.1 |
| Special properties | Extended temperature range |
| Data management status | |
| Article revision | 06 |
| Insulation characteristics | |
| Overvoltage category | II (IEC 60664-1) |
| Pollution degree | 2 (EN 60664-1) |
| Maximum power dissipation for nominal condition | 1.8 W |
| Potentials: Axioline F local bus supply (UBus) | |
| Supply voltage | 5 V DC (via bus base module) |
| Current draw | max. 110 mA (at UBus 5 V DC) |
| typ. 105 mA (at UBus 5 V DC) | |
| Potentials: I/O supply (UA) | |
| Supply voltage | 24 V DC (Power connector) |
| Supply voltage range | 19.2 V DC ... 30 V DC (including all tolerances, including ripple) |
| Current draw | max. 31 mA |
| typ. 25.5 mA (Power supply from UA with 30 V DC) | |
| Protective circuit | Surge protection; electronic (35 V, 0.5 s) |
| Reverse polarity protection (parallel) | |
| Undervoltage detection; at 17 V | |
| Surge voltage detection; No | |
| Conductor connection | |
| Connection method | Push-in connection |
| Conductor cross section rigid | 0.2 mm² ... 1.5 mm² |
| Conductor cross section flexible | 0.2 mm² ... 1.5 mm² |
| Conductor cross section AWG | 24 ... 16 |
| Stripping length | 8 mm |
| Connection method | Push-in connection |
| Note on the connection method | Note the specification in the section Conductor cross sections, and stripping and insertion lengths. |
| Conductor cross section, rigid | 0.2 mm² ... 1.5 mm² |
| Conductor cross section, flexible | 0.2 mm² ... 1.5 mm² |
| Conductor cross section AWG | 24 ... 16 |
| Stripping length | 8 mm |
| Ambient conditions | |
| Ambient temperature (operation) | -35 °C ... 60 °C |
| Degree of protection | IP20 |
| Degree of protection at installation location | min. IP54 |
| Note | Recommendation Do not use the AXL F PSAI8 I 1F in an atmosphere that contains corrosive gas. |
| Air pressure (operation) | 70 kPa ... 108 kPa |
| Air pressure (storage/transport) | 66 kPa ... 108 kPa |
| Ambient temperature (storage/transport) | -40 °C ... 85 °C |
| Permissible humidity (operation) | 5 % ... 95 % (non-condensing) |
| Permissible humidity (storage/transport) | 5 % ... 95 % (non-condensing) |
| Protection class | III (IEC 61140, EN 61140, VDE 0140-1) |
| Air clearances and creepage distances | |
| Air clearances and creepage distances | IEC 60664-1 |
| Mounting type | DIN rail mounting |
| Mounting position | any |
Your advantages
Up to Cat. 4/PL e in accordance with EN ISO 13849-1, SIL 3 in accordance with EN IEC 62061, SIL 3 in accordance with IEC 61508
Safe analog value acquisition 4 ... 20 mA
8 safe inputs for 1-channel assignment
4 safe inputs for 2-channel assignment