PLC-RSC-230UC/ 1AU/SEN/SO46 - Relay module - 1125984

Product details

Technical data

Notes

Notes on operation	The PLC-ATP partition plate must be installed for voltages greater than 250 V (L1, L2, L3) between identical terminal blocks on adjacent modules.
Notes on operation	The PLC-ATP separating plate should be installed for safe isolation between adjacent modules
Assembly note	The PLC-ATP separating plate is required at the start and end of every PLC terminal strip.
Notes on operation	The system installer must ensure the touch protection of the product (at voltages > 25 V AC/60 V DC). The product is a built-in device without protection against direct contact.
Notes on operation	If the specified maximum values for multi-layer contact relays are exceeded, the gold plating is destroyed. The maximum values of the power contact relay are then valid. This can result in a shorter service life than with a pure power contact.

Product properties

Product type	Relay Module
Product family	PLC-INTERFACE
Application	Input function
Operating mode	100% operating factor
Mechanical service life	2x 10⁷ cycles
Insulation characteristics: Air clearances and creepage distances
Insulation	Safe isolation, reinforced insulation
Overvoltage category	III
Pollution degree	3
Data management status
Date of last data management	12.11.2024

Electrical properties

Maximum power dissipation for nominal condition	2.3 W
Test voltage (Winding/contact)	4 kV_rms (50 Hz, 1 min., winding/contact)
Air clearances and creepage distances
Rated insulation voltage	250 V AC
Rated surge voltage	6 kV

Input data

Coil side
Nominal input voltage U_N	230 V AC
	220 V DC
Input voltage range	179.4 V AC ... 264.5 V AC (20 °C)
	171.6 V DC ... 253 V DC (20 °C)
Nominal voltage (plugged-in electromechanical relay)	60 V DC
Mains frequency	50/60 Hz
Drive and function	monostable
Drive (polarity)	polarized
Typical input current at U_N	8.8 mA (50 Hz)
	10 mA (60 Hz)
Typical response time	7 ms
Typical release time	20 ms
Typical release voltage	80 V AC
Protective circuit	Bridge rectifier
	RC element
Status display	LED (yellow)

Output data

Switching
Contact switching type	1 N/O contact
Type of switch contact	Single contact
Contact material	AgSnO, hard gold-plated
Maximum switching voltage	30 V AC
	36 V DC
Minimum switching voltage	100 mV (at 10 mA)
Limiting continuous current	50 mA
Maximum inrush current	50 mA
Min. switching current	1 mA (24 V)
Short-circuit current	200 A (conditional short-circuit current)
Interrupting rating (ohmic load) max.	1.2 W (24 V DC)
Switching capacity min.	0.12 W
Output fuse	4 A gL/gG NEOZED

Connection data

Connection method	Screw connection
Stripping length	8 mm
Screw thread	M3
Conductor cross section rigid	0.14 mm² ... 2.5 mm²
Conductor cross section flexible	0.14 mm² ... 2.5 mm²
	0.2 mm² ... 2.5 mm² (Single ferrule)
	2x 0.5 mm² ... 1.5 mm² (TWIN ferrule)
Conductor cross section AWG	26 ... 14
Tightening torque	0.45 Nm ... 0.55 Nm (Usually these terminal blocks must be supported during conductor connection (held by one hand, supported on the housing))

Dimensions

Width	6.2 mm
Height	80 mm
Depth	94 mm

Material specifications

Color	gray (RAL 7042)

Environmental and real-life conditions

Ambient conditions
Degree of protection (Relay base)	IP20 (Relay base)
Degree of protection (Relay)	RT III (Relay)
Degree of protection (Installation location)	≥ IP54 (Installation location)
Ambient temperature (operation)	-40 °C ... 55 °C
Ambient temperature (storage/transport)	-40 °C ... 85 °C
Altitude	≤ 2000 m

Approvals

CE
Certificate	CE-compliant
UKCA
Certificate	UKCA-compliant
Shipbuilding approval
Certificate	TAE0000196
Corrosive gas test
Identification	ISA-S71.04. G3 Harsh Group
Identification		EN 60068-2-60
Shipbuilding data
Temperature	D
Humidity	A
Vibration	B/C
EMC	B
Enclosure	Required protection according to the Rules shall be provided upon installation on board

EMC data

Electromagnetic compatibility	Conformance with EMC directive
Low Voltage Directive	Conformance with Low Voltage Directive

Standards and regulations

Air clearances and creepage distances
Standards/regulations	EN 61810
	IEC 60947-5-1

Mounting

Mounting type	DIN rail mounting
Assembly note	in rows with zero spacing
Mounting position	any

Commercial data

Item number	1125984
Packing unit	10 pc
Minimum order quantity	1 pc
Product key	DK622M
GTIN	4063151052980
Weight per piece (including packing)	36.48 g
Weight per piece (excluding packing)	30.04 g
Country of origin	DE

Classifications

Approvals

Environmental product compliance

ECLASS-11.0	27371601
ECLASS-12.0	27371601
ECLASS-13.0	27371601

EU RoHS
Fulfills EU RoHS substance requirements	Yes
Exemption	7(a), 7(c)-I
China RoHS
Environment friendly use period (EFUP)	EFUP-50 An article-related China RoHS declaration table can be found in the download area for the respective article under "Manufacturer declaration". For all articles with EFUP-E, no China RoHS declaration table issued and required.
EU REACH SVHC
REACH candidate substance (CAS No.)	Lead (CAS: 7439-92-1)
SCIP	c9206f5e-adf0-4f95-a2c3-da794e713b8a

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

PLC-RSC-230UC/ 1AU/SEN/SO46 - Relay module

1125984

Product details

ECLASS

ETIM

UNSPSC

EAC

DNV GL

EAC

cULus Listed

Compatible products

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

PLC-RSC-230UC/ 1AU/SEN/SO46 - Relay module 1125984

Product details

ECLASS

ETIM

UNSPSC

Compatible products

FBST 500-PLC RD - Continuous plug-in bridge 2966786

FBST 500-PLC BU - Continuous plug-in bridge 2966692

FBST 500-PLC GY - Continuous plug-in bridge 2966838

FBST 6-PLC RD - Single plug-in bridge 2966236

FBST 6-PLC BU - Single plug-in bridge 2966812

FBST 6-PLC GY - Single plug-in bridge 2966825

FBST 8-PLC GY - Single plug-in bridge 2967688

ZB 6:UNBEDRUCKT - Zack marker strip 1051003

ZB 6 CUS - Zack marker strip 0824992

ZB 6,LGS:FORTL.ZAHLEN - Zack marker strip 1051016

ZB 6,QR:FORTL.ZAHLEN - Zack marker strip 1051029

ZB 6,LGS:GLEICHE ZAHLEN - Zack marker strip 1051032

ZB 6,LGS:L1-N,PE - Marker for terminal blocks 1051414

ZB 6,LGS:U-N - Marker for terminal blocks 1051430

UC-TM 6 - Marker for terminal blocks 0818085

UC-TM 6 CUS - Marker for terminal blocks 0824589

UCT-TM 6 - Marker for terminal blocks 0828736

UCT-TM 6 CUS - Marker for terminal blocks 0829602

NS 35/ 7,5 PERF 2000MM - DIN rail perforated 0801733

NS 35/ 7,5 UNPERF 2000MM - DIN rail, unperforated 0801681

NS 35/ 7,5 WH PERF 2000MM - DIN rail perforated 1204119

NS 35/ 7,5 WH UNPERF 2000MM-VPE 10 - DIN rail, unperforated 1204122

NS 35/ 7,5 AL UNPERF 2000MM - DIN rail, unperforated 0801704

NS 35/ 7,5 ZN PERF 2000MM - DIN rail perforated 1206421

NS 35/ 7,5 ZN UNPERF 2000MM - DIN rail, unperforated 1206434

NS 35/ 7,5 CU UNPERF 2000MM-VPE 10 - DIN rail, unperforated 0801762

NS 35/ 7,5 CAP - End cap 1206560

NS 35/15 PERF 2000MM - DIN rail perforated 1201730

NS 35/15 UNPERF 2000MM - DIN rail, unperforated 1201714

NS 35/15 WH PERF 2000MM - DIN rail perforated 0806602

NS 35/15 WH UNPERF 2000MM-VPE 10 - DIN rail, unperforated 1204135

NS 35/15 AL UNPERF 2000MM - DIN rail, unperforated 1201756

NS 35/15 ZN PERF 2000MM - DIN rail perforated 1206599

NS 35/15 ZN UNPERF 2000MM - DIN rail, unperforated 1206586

NS 35/15 CU UNPERF 2000MM-VPE 10 - DIN rail, unperforated 1201895

NS 35/15 CAP - End cap 1206573

NS 35/15-2,3 UNPERF 2000MM-VPE 10 - DIN rail, unperforated 1201798

PLC-ATP BK - Separating plate 2966841

PLC-ESK GY - Power terminal block 2966508

SZF 1-0,6X3,5 - Screwdriver 1204517

PLC-RSC-230UC/ 1AU/SEN/SO46 - Relay module

1125984