1. Home
  2. Products
  3. Relays and optocouplers
  4. Solid-state relays and electromechanical relays
  5. PLC-RSC- 12DC/ 1IC/ACT - Relay Module

PLC-RSC- 12DC/ 1IC/ACT - Relay Module
1078800

PLC-INTERFACE for high switch-on currents, consisting of PLC-BSC.../1 IC/ACT basic terminal block with push-in connection and plug-in miniature relay, for mounting on DIN rail NS 35/7,5, max. switch-on current up to 130 A, 1 N/O contact, input voltage 12 V DC

Product Details

Notes on operation Separating plate PLC-ATP must be installed for voltages larger than 250 V (L1, L2, L3) between identical terminal blocks in adjacent modules. Potential bridging is then carried out with FBST 8-PLC... or FBST 500....
Notes on operation The PLC-ATP separating plate should be installed for safe isolation between adjacent modules
Assembly instruction: The PLC-ATP separating plate is required at the start and end of every PLC terminal strip.
Notes on operation The system installer must ensure the touch protection of the product (at voltages > 25 V AC/60 V DC). The product is a built-in device without protection against direct contact.
Product type Relay Module
Product family PLC-INTERFACE
Application high inrush currents
Operating mode 100% operating factor
Mechanical service life 3x 107 cycles
Insulation characteristics
Insulation Safe isolation, reinforced insulation
Insulation characteristics: Standards/regulations
Insulation Safe isolation, reinforced insulation
Overvoltage category III
Pollution degree 3
Maximum power dissipation for nominal condition 0.4 W
Test voltage (Winding/contact) 4 kV AC (50 Hz, 1 min., winding/contact)
Standards/regulations
Rated insulation voltage 250 V AC
Rated surge voltage 6 kV
Coil side
Nominal input voltage UN 12 V DC
Input voltage range 10.32 V DC ... 16.8 V DC (20 °C)
Typical input current at UN 33 mA
Typical response time 8 ms
Typical release time 10 ms
Coil voltage 12 V DC
Protective circuit Reverse polarity protection; Polarity protection diode
Freewheeling diode; Freewheeling diode
Operating voltage display Yellow LED
Switching
Contact type 1 N/O contact
Type of switch contact Single contact
Drive and function monostable
Drive (polarity) polarized
Contact material AgSnO2
Maximum switching voltage 250 V AC/DC (The separating plate PLC-ATP should be installed for voltages larger than 250 V (L1, L2, L3) between identical terminal blocks in adjacent modules. Potential bridging is then carried out with FBST 8-PLC... or ...FBST 500...)
Minimum switching voltage 12 V (100 mA)
Limiting continuous current 6 A
10 A (the value is permissible if both connections 13, both connections 14 and both connections BB are bridged)
Maximum inrush current 80 A (20 ms)
130 A (peak, at capacitive load, 230 V AC, 24 μF)
Min. switching current 100 mA (12 V)
Interrupting rating (ohmic load) max. 144 W (at 24 V DC)
58 W (at 48 V DC)
48 W (at 60 V DC)
50 W (at 110 V DC)
80 W (at 220 V DC)
85 W (for 250 V DC)
1500 VA (for 250 V AC)
Interrupting rating (ohmic load) max. bridged 240 W (for 24 V DC. The value is permissible if both connections 13, both connections 14 and both connections BB are bridged.)
2500 VA (for 250 V AC. The value is permissible if both connections 13, both connections 14 and both connections BB are bridged.)
Switching capacity min. 1200 mW
Switching capacity 2 A (at 24 V, DC13)
0.2 A (at 110 V, DC13)
0.2 A (at 250 V, DC13)
6 A (at 24 V, AC15)
6 A (at 120 V, AC15)
6 A (at 250 V, AC15)
Connection method Screw connection
Stripping length 8 mm
Screw thread M3
Conductor cross section solid 0.14 mm² ... 2.5 mm²
Conductor cross section flexible 0.14 mm² ... 2.5 mm²
0.2 mm² ... 2.5 mm² (Single ferrule)
2x 0.5 mm² ... 1.5 mm² (TWIN ferrule)
Conductor cross section AWG 26 ... 14
Tightening torque 0.6 Nm ... 0.8 Nm
Width 14 mm
Height 80 mm
Depth 94 mm
Flammability rating according to UL 94 V0 (Housing)
Ambient conditions
Degree of protection Relay RT II (Relay)
IP20 (Relay base)
≥ IP54 (Installation location)
Ambient temperature (operation) -40 °C ... 60 °C
Ambient temperature (storage/transport) -40 °C ... 85 °C
Altitude ≤ 2000 m
Corrosive gas test
Identification ISA-S71.04. G3 Harsh Group
EN 60068-2-60
Standards/regulations
Standards/regulations IEC 60947-5-1
Mounting type DIN rail mounting
Assembly instructions in rows with zero spacing
Mounting position any
Item number 1078800
Packing unit 1 pc
Minimum order quantity 1 pc
Sales Key C05
Product Key CK621A
Catalog Page Page 382 (C-5-2019)
GTIN 4055626794532
Weight per Piece (including packing) 76.38 g
Weight per Piece (excluding packing) 44.1 g
Customs tariff number 85364190
Country of origin DE

ECLASS

ECLASS-9.0 27371601
ECLASS-10.0.1 27371601
ECLASS-11.0 27371601
ECLASS-12.0 27371601
ECLASS-13.0 27371601

ETIM

ETIM 8.0 EC001437

UNSPSC

UNSPSC 21.0 39122300

cUL Recognized

Approval ID: FILE E 238705

UL Recognized

Approval ID: FILE E 238705

EAC

Approval ID: TR_TS_D_00573_c

DNV GL

Approval ID: TAE0000196
Approval Specification Data
Nominal Voltage UN Nominal Current IN Cross Section AWG Cross Section mm2

UL Listed

Approval ID: FILE E 172140

cUL Listed

Approval ID: FILE E 172140

cULus Recognized

cULus Listed

REACh SVHC Lead 7439-92-1
Hexahydromethylphthalic anhydride
China RoHS Environmentally Friendly Use Period = 50 years
For information on hazardous substances, refer to the manufacturer’s declaration available under “Downloads”

Compatible Products

Your advantages

Direct connection of load return line thanks to actuator version
Safe isolation according to DIN EN 50178 between coil and contact
Max. inrush current of 130 A
Functional plug-in bridges