PLC-RPT-230UC/21HC/SO46 - Relay module - 1136242

Product details

Technical data

Notes

Notes on operation	The PLC-ATP partition plate must be installed for voltages greater than 250 V (L1, L2, L3) between identical terminal blocks on adjacent modules.
Notes on operation	The PLC-ATP separating plate should be installed for safe isolation between adjacent modules
Notes on operation	The system installer must ensure the touch protection of the product (at voltages > 25 V AC/60 V DC). The product is a built-in device without protection against direct contact.
Assembly note	The PLC-ATP separating plate is required at the start and end of every PLC terminal strip.

Product properties

Product type	Relay Module
Product family	PLC-INTERFACE
Application	Filter to prevent interference
Operating mode	100% operating factor
Mechanical service life	approx. 3x 10⁷ cycles
Insulation characteristics: Air clearances and creepage distances between the power circuits
Insulation	Basic insulation
Overvoltage category	III
Pollution degree	3
Data management status
Date of last data management	17.01.2025

Electrical properties

Maximum power dissipation for nominal condition	2.3 W
Test voltage (Winding/contact)	4 kV_rms (50 Hz, 1 min., winding/contact)
Air clearances and creepage distances between the power circuits
Rated insulation voltage	250 V AC
Rated surge voltage	4 kV (Safe isolation, reinforced insulation, and 6 kV between input circuit and output contact current paths)

Input data

Coil side
Nominal input voltage U_N	230 V AC
	220 V DC
Input voltage range	179.4 V AC ... 264.5 V AC (20 °C)
	171.6 V DC ... 253 V DC (20 °C)
Nominal voltage (plugged-in electromechanical relay)	110 V DC
Mains frequency	50/60 Hz
Drive and function	monostable
Drive (polarity)	polarized
Typical input current at U_N	8.5 mA (50 Hz)
	10 mA (60 Hz)
Typical response time	7 ms
Typical release time	10 ms
Typical release voltage	60 V AC
Protective circuit	RC element
	Bridge rectifier
Status display	LED (yellow)

Output data

Switching
Contact switching type	1 changeover contact
Type of switch contact	Single contact
Contact material	AgNi
Maximum switching voltage	250 V AC/DC
Minimum switching voltage	12 V (10 mA)
Limiting continuous current	6 A
Limiting continuous current		10 A (value applies to connections 12. If connections 12 are bridged, the normal value applies.)
Maximum inrush current	30 A (300 ms, N/O contact)
Min. switching current	10 mA (12 V)
Interrupting rating (ohmic load) max.	144 W (24 V DC)
		240 W (24 V DC, value is valid for connections 12. If connections 12 are bridged, the normal value applies.)
		58 W (48 V DC)
		48 W (60 V DC)
		50 W (110 V DC)
		80 W (220 V DC)
		1500 VA (250 V AC)
		2500 W (250 V AC, value is valid for connections 12. If connections 12 are bridged, the normal value applies.)
Switching capacity	2 A (DC13, 24 V)
		0.2 A (DC13, 250 V)
		6 A (AC15, 24 V)
		6 A (AC15, 250 V)

Connection data

Connection method	Push-in connection
Stripping length	10 mm
Conductor cross section rigid	0.14 mm² ... 2.5 mm²
Conductor cross section flexible	0.14 mm² ... 2.5 mm²
	0.2 mm² ... 2.5 mm² (Single ferrule)
	2x 0.5 mm² ... 1 mm² (TWIN ferrule)
Conductor cross section AWG	26 ... 14

Dimensions

Width	14 mm
Height	80 mm
Depth	94 mm

Material specifications

Color	gray (RAL 7042)

Environmental and real-life conditions

Ambient conditions
Degree of protection (Relay base)	IP20 (Relay base)
Degree of protection (Relay)	RT II (Relay)
Degree of protection (Installation location)	IP54 (Installation location)
Ambient temperature (operation)	-40 °C ... 55 °C
Ambient temperature (storage/transport)	-40 °C ... 85 °C
Altitude	≤ 2000 m

Approvals

CE
Certificate	CE-compliant
UKCA
Certificate	UKCA-compliant
Shipbuilding approval
Certificate	TAE0000196
Corrosive gas test
Identification	ISA-S71.04. G3 Harsh Group
Identification		EN 60068-2-60
Shipbuilding data
Temperature	D
Humidity	A
Vibration	B/C
EMC	B
Enclosure	Required protection according to the Rules shall be provided upon installation on board

EMC data

Electromagnetic compatibility	Conformance with EMC directive
Low Voltage Directive	Conformance with Low Voltage Directive

Standards and regulations

Air clearances and creepage distances between the power circuits
Standards/regulations	IEC 60947-5-1

Mounting

Mounting type	DIN rail mounting
Assembly note	in rows with zero spacing
Mounting position	any

Commercial data

Item number	1136242
Packing unit	10 pc
Minimum order quantity	10 pc
Sales key	C461
Product key	DK62BM
GTIN	4063151070670
Weight per piece (including packing)	74.4 g
Weight per piece (excluding packing)	74.1 g
Customs tariff number	85364900
Country of origin	DE

Classifications

Approvals

Environmental product compliance

ECLASS-11.0	27371601
ECLASS-12.0	27371601
ECLASS-13.0	27371601

EU RoHS
Fulfills EU RoHS substance requirements	Yes
Exemption	7(a), 7(c)-I
China RoHS
Environment friendly use period (EFUP)	EFUP-50 An article-related China RoHS declaration table can be found in the download area for the respective article under "Manufacturer declaration". For all articles with EFUP-E, no China RoHS declaration table issued and required.
EU REACH SVHC
REACH candidate substance (CAS No.)	Hexahydromethylphthalic anhydride (CAS: n/a)
REACH candidate substance (CAS No.)		Lead (CAS: 7439-92-1)
SCIP	6dd2285c-3fdc-4cb0-b4c2-31e7fac23a95

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

PLC-RPT-230UC/21HC/SO46 - Relay module

1136242

Product details

ECLASS

ETIM

UNSPSC

EAC

EAC

DNV GL

cULus Listed

Compatible products

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

PLC-RPT-230UC/21HC/SO46 - Relay module 1136242

Product details

ECLASS

ETIM

UNSPSC

Compatible products

ZB 10:UNBEDRUCKT - Zack marker strip 1053001

ZB 10 CUS - Zack marker strip 0824941

ZB10,LGS:FORTL.ZAHLEN - Zack marker strip 1053014

ZB10,QR:FORTL.ZAHLEN - Zack marker strip 1053027

ZB10,LGS:L1-N,PE - Marker for terminal blocks 1053412

ZB10,LGS:U-N - Marker for terminal blocks 1053438

UC-TM 10 - Marker for terminal blocks 0818069

UC-TM 10 CUS - Marker for terminal blocks 0824605

UCT-TM 10 - Marker for terminal blocks 0829142

UCT-TM 10 CUS - Marker for terminal blocks 0829623

ZB 12:UNPRINTED - Zack marker strip 0812120

ZB 12 CUS - Zack marker strip 0824942

ZB 12,LGS:L1-N,PE - Zack marker strip 0812146

UC-TM 12 - Marker for terminal blocks 0819194

UC-TM 12 CUS - Marker for terminal blocks 0824613

UCT-TM 12 - Marker for terminal blocks 0829144

UCT-TM 12 CUS - Marker for terminal blocks 0829630

NS 35/ 7,5 PERF 2000MM - DIN rail perforated 0801733

NS 35/ 7,5 UNPERF 2000MM - DIN rail, unperforated 0801681

NS 35/ 7,5 WH PERF 2000MM - DIN rail perforated 1204119

NS 35/ 7,5 WH UNPERF 2000MM-VPE 10 - DIN rail, unperforated 1204122

NS 35/ 7,5 AL UNPERF 2000MM - DIN rail, unperforated 0801704

NS 35/ 7,5 ZN PERF 2000MM - DIN rail perforated 1206421

NS 35/ 7,5 ZN UNPERF 2000MM - DIN rail, unperforated 1206434

NS 35/ 7,5 CU UNPERF 2000MM-VPE 10 - DIN rail, unperforated 0801762

NS 35/ 7,5 CAP - End cap 1206560

NS 35/15 PERF 2000MM - DIN rail perforated 1201730

NS 35/15 UNPERF 2000MM - DIN rail, unperforated 1201714

NS 35/15 WH PERF 2000MM - DIN rail perforated 0806602

NS 35/15 WH UNPERF 2000MM-VPE 10 - DIN rail, unperforated 1204135

NS 35/15 AL UNPERF 2000MM - DIN rail, unperforated 1201756

NS 35/15 ZN PERF 2000MM - DIN rail perforated 1206599

NS 35/15 ZN UNPERF 2000MM - DIN rail, unperforated 1206586

NS 35/15 CU UNPERF 2000MM-VPE 10 - DIN rail, unperforated 1201895

NS 35/15 CAP - End cap 1206573

NS 35/15-2,3 UNPERF 2000MM-VPE 10 - DIN rail, unperforated 1201798

PLC-ATP BK - Separating plate 2966841

PLC-ESK GY - Power terminal block 2966508

SZF 1-0,6X3,5 - Screwdriver 1204517

REL-MR-110DC/21HC - Single relay 2961338

PLC-RPT-230UC/21HC/SO46 - Relay module

1136242