Device connector, rear mounting - PRC 5-FT25-MC6-150
1409213

Panel feed-through, Range of articles: PRC 35, Device connector, rear mounting, housing material: PPE, color: black, number of positions: 5, max. conductor cross section: 6 mm2, rated voltage: 690 V AC, rated current: 35 A, Connection method: Crimp connection, Type of contact: Pin, cable length: 150. This item is also available with other cable lengths. For your specific requirements, please contact your local PHOENIX CONTACT subsidiary.


Product Details




Order information: This item is also available with other cable lengths. For your specific requirements, please contact your local PHOENIX CONTACT subsidiary.
Safety note
Safety note • WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
• Assembled products may not be manipulated or improperly opened.
• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
• When using the product in direct connection with third-party manufacturers, the user is responsible.
• For operating voltages > 50 V AC, conductive connector housings must be grounded
• Ensure that the protective or functional ground has been properly connected.
• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
• Observe the corresponding technical data. You will find information:
o On the product
o On the packing label
o In the supplied documentation
o Online at phoenixcontact.com/products under the product
• Only use tools recommended by Phoenix Contact
• The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product.
• Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products
• Operate the connector only when it is fully plugged in.
• Operate the connector only when it is fully plugged in and interlocked.
• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
• Observe the minimum bending radius of the cable. Lay the cable without twisting it.
• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).

Product type Panel feed-through
Number of positions 5
Connection profile 4+PE
Locking type Snap-in locking
Insertion force 40 N ±10 N
Insulation characteristics
Protection class II
Degree of pollution 2

Dimensional drawing
Width 34.5 mm
Height 38.4 mm
Length 179.5 mm
Hole diameter 25.5 mm
Wrench size, union nut 32 mm

Rated voltage (III/2) 690 V
Nominal voltage ATD 690 V AC in accordance with IEC 61984
500 V AC in accordance with IEC 61535/2 PfG 1915
600 V AC In accordance with UL 2238
Rated surge voltage (III/2) 8 kV
Rated current 35 A (With 6 mm² conductor cross section in accordance with IEC 61984)
32 A (With 6 mm² conductor cross section in accordance with IEC 61535)
21.4 A (With 6 mm² conductor cross section and 85 °C in accordance with 2 PfG 1915)
28 A (with AWG 10, in accordance with UL 2237)

Mechanical data
Insertion force 40 N ±10 N

Color black
Color of the housing part black
Flammability rating according to UL 94 V0
Insulating material group I / CTI 600
Seal material EPDM
Contact material Cu alloy
Contact surface material Ag
Contact carrier material PPE
O-ring material Silicon
Cable gland material PPE
Housing material PPE

Insertion/withdrawal cycles 100
Pull-out-force 175 N ± 50 N

Cable length 150 mm
Cable structure
Single wire, material PVC
Wire diameter incl. insulation 4.8 mm ±0.15 mm
Single wire, cross section 6 mm²
Single wire, color blue, black, gray, brown, green/yellow
Ambient conditions
Halogen-free no

Mounting type Rear mounting

Degree of protection (when plugged in) IP66 / IP68 (2m / 24h) / IP69K
Degree of protection (not plugged in) IP65 (Lengthwise waterproofing)
Degree of protection IP66 / IP68 (2m / 24h) / IP69K
Ambient temperature (operation) -40 °C ... 105 °C (Depending on the current carrying capacity/derating curve)
Ambient temperature (storage/transport) -40 °C ... 70 °C
Ambient temperature (assembly) 5 °C ... 85 °C

Item number 1409213
Packing unit 1 pc
Minimum order quantity 10 pc
Sales Key A16
Product Key ABLCAA
Catalog Page Page 77 (NTK-2014)
GTIN 4046356864329
Weight per Piece (including packing) 76.58 g
Weight per Piece (excluding packing) 76.58 g
Customs tariff number 85444290
Country of origin PL


ECLASS

ECLASS-9.0 27440103
ECLASS-10.0.1 27440103
ECLASS-11.0 27440103

ETIM

ETIM 8.0 EC003570

UNSPSC

UNSPSC 21.0 39121400

EAC

Approval ID: B.01687

DNV GL

Approval ID: TAE00002KM

UL Listed

Approval ID: E221474-20150513
Approval Specification Data
Nominal Voltage UN Nominal Current IN Cross Section AWG Cross Section mm2
600 V 30 A 14 - 10

cUL Listed

Approval ID: E221474-20150513
Approval Specification Data
Nominal Voltage UN Nominal Current IN Cross Section AWG Cross Section mm2
600 V 30 A 14 - 10

TÜV Rheinland

Approval ID: R 60117904-0002
Approval Specification Data
Nominal Voltage UN Nominal Current IN Cross Section AWG Cross Section mm2
690 V 35 A

TÜV Rheinland

Approval ID: R 60117908
Approval Specification Data
Nominal Voltage UN Nominal Current IN Cross Section AWG Cross Section mm2
500 V 21.4 A

TÜV Rheinland

Approval ID: R 60117904-0001
Approval Specification Data
Nominal Voltage UN Nominal Current IN Cross Section AWG Cross Section mm2
500 V 32 A

cUL Listed

Approval ID: E468743-20190809
Approval Specification Data
Nominal Voltage UN Nominal Current IN Cross Section AWG Cross Section mm2
600 V 24 A

UL Listed

Approval ID: E468743-20190809
Approval Specification Data
Nominal Voltage UN Nominal Current IN Cross Section AWG Cross Section mm2
600 V 30 A

China RoHS Environmentally Friendly Use Period = 50 years
For information on hazardous substances, refer to the manufacturer’s declaration available under “Downloads”

Compatible Products

Your advantages

Up to 75% smaller in size than industrial connectors with the same rating
Locking mechanism can be unlocked manually or using a tool
Ideal for indoor and outdoor use due to weatherproof materials
Either pre-assembled or for assembly