DC power module - CHARX PS-M2/825DC/1000DC/30KW
1296467

CHARX power, Fast charging module for setting up DC charging stations, 19" rack mounting, CAN bus, output: 150 V DC...1000 V DC / 0 A...100 A


Product Details


The highly efficient power electronics system for rack mounting from Phoenix Contact features a high degree of investment security. It enables the cost-effective operation of your DC charging infrastructure for the fast charging of electric vehicles. The modular and scalable system is optimized for DC charging with high voltages and currents. Each system cabinet can provide a charging power of up to 360 kW.



Input voltage range 650 V DC ... 825 V DC
Derating < 650 V DC ... 300 V DC (46 W/V)
Nominal input voltage range 650 V DC ... 825 V DC
Supply system configuration DC grid (DC±, PE)
Input current 48 A (650 V DC)
38 A (825 V DC)
Inrush current limitation < 60 A
Insulation resistance > 10 MΩ

Efficiency > 95 % (POut >50%)
Output voltage range 150 V DC ... 1000 V DC
Output current range 0 A ... 100 A
Nominal power 30 kW
Power dissipation standby < 14 W
Protection against overvoltage at the output (OVP) > 1040 V DC
Derating > 45 °C ... 55 °C (1.2 A/K)
> 55 °C (3.2 A/K)
> 55 °C (1 kW/K)
Control deviation < 0.5 % (Voltage deviation static load change 20% ... 100%)
< 1 % (Current deviation Static load change 20 % ... 100 %)
± 0.2 % (Input voltage change ±20 %)
Switch-on delay < 8 s
Overshoot behavior ± 3 % (Switch-on procedure)

Battery technology Li-Ion

Input
Connection method Push-in connection
Conductor cross section solid 1.5 mm² ... 16 mm²
Conductor cross section flexible 1.5 mm² ... 16 mm²
Conductor cross section AWG 14 ... 6 (Cu)
2 conductors with the same cross section, flexible, with TWIN ferrule with plastic sleeve 1.5 mm² ... 4 mm²
Stripping length 18 mm
Output
Connection method T-LOX knee lever connection
Conductor cross section solid 10 mm² ... 50 mm²
Conductor cross section flexible 16 mm² ... 50 mm²
Conductor cross section AWG 4 ... 1 (Cu)
Stripping length 20 mm (10 mm² to 25 mm² = 18 mm, 35 mm² to 50 mm² = 20 mm)

Interface CAN bus
Number of interfaces 1
Connection method 2x RJ45 (pin assignment, CANopen standard)
Locking Locking clip
Transmission physics Twisted-Pair
Topology Line (daisy-chain connection)
Transmission speed 125 kbps
Transmission length max. 20 m
Supported protocols CAN 2.0B
Electrical isolation yes (primary/secondary)
no (PE)
Number of power modules as CAN bus devices max. 48 (within one CHARX control controller)
Termination resistor 120 Ω (Terminating the end device)

Electrical isolation between input and output yes
Insulation voltage input/output 2121 V DC
Insulation voltage input, output / housing 2121 V DC
Insulation voltage input, output/signal, communication 4242 V DC
Insulation voltage signal, communication/housing 707 V DC

Product type DC power module
MTBF (IEC 61709, SN 29500) > 300000 h
Service life 40000 h (40 °C)
70000 h (40 °C, fan)
Flow direction from front to back
Insulation characteristics
Protection class I

Dimensional drawing
Width 483 mm
Height 134 mm
Depth 550 mm

Mounting type 19" rack mounting

Housing material Zn-Al alloy

Ambient conditions
Degree of protection IP20
Ambient temperature (operation) -40 °C ... 70 °C
Ambient temperature (storage/transport) -40 °C ... 70 °C
Overtemperature protection (OTP) > 75 °C
Maximum altitude ≤ 4000 m (Derating >2000 m: 10% / 1000 m)
Permissible humidity (operation) ≤ 95 % (non-condensing)
Noise level < 60 dB (1 m)

Overvoltage category
IEC 60664-1 II
Electric vehicle conductive charging system - Part 1: General requirements
Standards/specifications IEC 61851-1
Electric vehicle conductive charging system - Part 1: General requirements
Standards/specifications IEC 61851-23

EMC requirements for noise emission EN 61000-6-3
EMC requirements for noise immunity EN 61000-6-1
Interference emission Class B (IEC 61000-6-3)
Noise immunity IEC 61000-6-1

Item number 1296467
Packing unit 1 pc
Minimum order quantity 1 pc
Sales Key C33
Product Key CMER3E
GTIN 4063151531973
Weight per Piece (including packing) 35 g
Weight per Piece (excluding packing) 33,000 g
Customs tariff number 85044055
Country of origin CN


ECLASS

ECLASS-11.0 27144790

ETIM

ETIM 8.0 EC002884

EAC

Approval ID: RU*DE*01.B.02076/21

TÜV SÜD Type tested

Approval ID: N8A 029429 0025
Approval Specification Data
Nominal Voltage UN Nominal Current IN Cross Section AWG Cross Section mm2
125 V - 1.5

EAC

Approval ID: RU*DE*01.B.85589/21

REACh SVHC Lead 7439-92-1
China RoHS Environmentally Friendly Use Period = 10;
For information on hazardous substances, refer to the manufacturer’s declaration available under “Downloads”

Your advantages

Low installation costs with Plug and Play and efficient operation due to the high degree of efficiency
Save space with the innovative design and high power density
Fast repair due to hot swappable power modules
Scalable power for each charging point with the flexible assembly of system cabinets and connection of power modules
The operation of large charging parks in the megawatt range is made possible by connecting multiple system cabinets together