PACT RCP-4000A-1A-D140-10M - Current transformer

1033483

Set consisting of one 1 A measuring transducer and one Rogowski coil with signal line. Length of Rogowski coil: 450 mm, diameter: 140 mm. Length of signal line: 10 m. The Rogowski coil measures the AC current of busbars and power lines.

Product type	Current transformer
Insulation characteristics
Insulation	double insulation
Insulation characteristics
Insulation	double insulation
Overvoltage category	III (1000 V, to neutral conductor)
	IV (600 V, to neutral conductor)
Pollution degree	2

Electrical isolation	Reinforced insulation in accordance with IEC 61010-1
Typical measuring error	< 1 %
Protective circuit	Surge protection; 33 V suppressor diode
Temperature coefficients	0.005 %/K (+10 °C ... +70 °C, both components have the same ambient temperature)
	0.07 %/K (-20 °C ... +10 °C, both components have the same ambient temperature)
Measuring coil
Conductor structure signal line	2x 0.22 mm (Signal (tinned))
	1x 0.22 mm (Shielding (tinned))
Insulation	double insulation
Rated insulation voltage	1000 V AC (rms CAT III)
	600 V AC (rms CAT IV)
Test voltage	10.45 kV DC (60 s)
Basic accuracy	<± 0.2 %
Measuring transducers
Linearity error	< 0.5 % (From the range end value)
Maximum transmission error	≤ 0.5 % (From the range end value)
Frequency range	45 Hz ... 65 Hz
Max. detectable harmonics	< 2 kHz
Current consumption	< 190 mA (at 19.2 V)
Test voltage	1.5 kV AC (Supply/input and output: 50 Hz, 1 min)
General
Can be calibrated	no
Class	1
Accuracy class	1
Converter type	Rogowski coil and 1 A measuring transducer
Supply: Measuring transducers
Nominal supply voltage	24 V DC -20 % ... +25 %
Nominal supply voltage range	19.2 V DC ... 30 V DC
Max. current consumption	190 mA
Power consumption	4 W

Frequency
Designation	Measuring coil
Frequency measuring range	40 Hz ... 20000 Hz
Position error	<± 0.1 % (typical)
Linearity error	< 0.1 %
Signal
Input signal (at 50 Hz)	100 mV (1000 A)
Curve type	Sine
Input impedance	27 kΩ (smallest measuring range)
Current transformers
Configurable/programmable	Via DIP switches
Rated power	1.5 VA
Primary rated current I_pn	0 A AC ... 100 A AC
	0 A AC ... 250 A AC
	0 A AC ... 400 A AC
	0 A AC ... 630 A AC
	0 A AC ... 1000 A AC
	0 A AC ... 1500 A AC
	0 A AC ... 2000 A AC
	0 A AC ... 4000 A AC
Phase angle	< 1 °
Can be calibrated	no
Class	1
Accuracy class	1
Converter type	Rogowski coil and 1 A measuring transducer

Signal
Designation	Measuring coil
Output signal (at 50 Hz)	100 mV (no load, at 1,000 A)
Output voltage (in no-load operation)	V_OUT = M * dI/dt
Output voltage (sinusoidal, in no-load operation)	100 mV (V_OUT = 2 * π * M * f * I (M = 0.318 μH; example: At 50 Hz; I = 1,000 A))
Accuracy class	< 1
Signal
Designation	Measuring transducer
Current output signal	0 A AC ... 1 A AC
Rated power	1.5 VA
Load	0 Ω ... 1.5 Ω
Max. distances for copper cables at P_{N max}	32 m (0.75 mm² (AWG 20))
	64 m (1.5 mm² (AWG 16))
	107 m (2.5 mm² (AWG 14))

Measuring transducer side
Connection method	Screw connection
Stripping length	7 mm
Screw thread	M3
Conductor cross section rigid	0.2 mm² ... 2.5 mm²
Conductor cross section flexible	0.2 mm² ... 2.5 mm²
Conductor cross section AWG	24 ... 14
Tightening torque	0.5 Nm ... 0.6 Nm

Operating voltage display	Green LED

Item dimensions
Width	22.5 mm
Height	85 mm
Depth	70.4 mm
Measuring coil
Length	450 mm
Diameter	8.3 mm ±0.2 mm
Measuring coil when installed
Diameter	140 mm
Signal line
Length	10 m
Width	22.5 mm
Height	85 mm
Depth	70.4 mm

Coil material	Elastollan
Housing material	PC
	Polyamide

Ambient conditions
Measuring coil degree of protection	IP67 (not assessed by UL)
Measuring transducer degree of protection	IP20
Ambient temperature (operation)	-30 °C ... 80 °C (Measuring coil)
	-20 °C ... 70 °C (Measuring transducer)
Ambient temperature (storage/transport)	-40 °C ... 80 °C (Measuring coil)
	-25 °C ... 85 °C (Measuring transducer)
Altitude	< 2000 m
Permissible humidity (operation)	5 % ... 95 % (non-condensing)

CE
Certificate	CE-compliant
UKCA
Certificate	UKCA-compliant
CMIM
Certificate	CMIM-compliant
UL, USA/Canada
Identification	UL 61010 Recognized
Note	Measuring coil
UL, USA/Canada
Identification	UL 508 Listed
Note	Measuring transducer

Noise immunity	EN 61000-6-3
Electromagnetic compatibility	Conformance with EMC directive
Noise emission	EN 61000-6-4

Electrical isolation	Reinforced insulation in accordance with IEC 61010-1
Standards/regulations	IEC 61010-1
	IEC 61010-2-032

Mounting type	DIN rail mounting

Item number	1033483
Packing unit	1 pc
Minimum order quantity	1 pc
Sales key	C444
Product key	CK4A12
Catalog page	Page 222 (C-5-2019)
GTIN	4055626539218
Weight per piece (including packing)	598.5 g
Weight per piece (excluding packing)	440.3 g
Customs tariff number	85437090
Country of origin	DE

Compatible products

ECLASS-11.0	27210902
ECLASS-13.0	27210902
ECLASS-12.0	27210902


REACh SVHC	Lead 7439-92-1

China RoHS	Environmentally Friendly Use Period = 50 years
		For information on hazardous substances, refer to the manufacturer’s declaration available under “Downloads”

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

PACT RCP-4000A-1A-D140-10M - Current transformer

1033483

Product details

ECLASS

ETIM

UNSPSC

EAC

Compatible products

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

PACT RCP-4000A-1A-D140-10M - Current transformer 1033483

Product details

ECLASS

ETIM

UNSPSC

Compatible products

PACT RCP-CLAMP - Holder 2904895

PACT RCP-CLAMP-5-10 - Holder 2907888

PACT RCP-4000A-1A-D140-10M - Current transformer

1033483