Contact insert - VC-TFS 7-PEA
1607481

Contact insert, Range of articles: VARIOCON, Contact insert, type: VC4, housing material: PA, color: light grey, number of positions: 7, min. conductor cross section: 0.5 mm2, max. conductor cross section: 16 mm2, rated current: 70 A, Connection method: Screw connection, Type of contact: Socket. Connectors may only be connected/disconnected when under no load.


Product Details




General Connectors may only be connected/disconnected when under no load.
Safety note
Safety note WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
• The products are suitable for applications in plant, controller, and electrical device engineering.
• When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
• Assembled products may not be manipulated or improperly opened.
• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
• When using the product in direct connection with third-party manufacturers, the user is responsible.
• For operating voltages > 50 V AC, conductive connector housings must be grounded
• Ensure that the protective or functional ground has been properly connected.
• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
• Observe the corresponding technical data. You will find information:
o On the product
o On the packing label
o In the supplied documentation
o Online at phoenixcontact.com/products under the product
• Only use tools recommended by Phoenix Contact
• The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product.
• Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products
• Operate the connector only when it is fully plugged in.
• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
• Observe the minimum bending radius of the cable. Lay the cable without twisting it.
• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).

Type VC4
Product type Contact insert
Number of positions 7
Connection profile 6+PE
Series VC-M
VC-D
Insulation characteristics
Degree of pollution 3

Rated voltage (II/2) 1000 V
Rated voltage (III/2) 1000 V
Rated voltage (III/3) 690 V
Rated voltage (III/3) 690 V
Rated surge voltage 6 kV
Rated surge voltage (II/2) 6 kV
Rated surge voltage (III/2) 8 kV
Rated surge voltage (III/3) 8 kV
Rated surge voltage 6 kV
Rated current 70 A
Rated current 70 A
Rated current 70 A

Dimensional drawing
Width 95.1 mm
Height 27.3 mm
Length 42.8 mm

Color light grey
Color of the housing part gray
Material Polyamide
Flammability rating according to UL 94 V0
Insulating material group I
Contact material E-Cu 58
Contact surface material hard-silver plated
Contact carrier material PA
Cable gland material CuZn
Housing material PA

Insertion/withdrawal cycles ≥ 50

Cable structure
Single wire, cross section 0.5 mm² 16 mm²
Stripping length of the individual wire 12 mm
Ambient conditions
Halogen-free yes

Ambient conditions
Ambient temperature (operation) -40 °C ... 100 °C

Item number 1607481
Packing unit 1 pc
Minimum order quantity 5 pc
Sales Key A16
Product Key ABLACC
Catalog Page Page 33 (C-2-2013)
GTIN 4017918969134
Weight per Piece (including packing) 77.56 g
Weight per Piece (excluding packing) 77.56 g
Customs tariff number 85366990
Country of origin PL


ECLASS

ECLASS-10.0.1 27440205
ECLASS-9.0 27440205
ECLASS-11.0 27440223

ETIM

ETIM 8.0 EC003557

UNSPSC

UNSPSC 21.0 39121400

cUL Recognized

Approval ID: FILE E 118976
Approval Specification Data
Nominal Voltage UN Nominal Current IN Cross Section AWG Cross Section mm2
600 V 45 A 20 - 6

UL Recognized

Approval ID: FILE E 118976
Approval Specification Data
Nominal Voltage UN Nominal Current IN Cross Section AWG Cross Section mm2
600 V 55 A 20 - 6

EAC

Approval ID: B.01687

cULus Recognized


China RoHS Environmentally friendly use period: unlimited = EFUP-e
No hazardous substances above threshold values

Your advantages

Compact design
Universal connection
Proven COMBICON technology
Can be keyed to prevent incorrect connection