ES-C1F-C-CO1 - Connector

1231074

Connector, Range of articles: BPP, housing material: PPE, color: red/black, number of positions: 1, min. conductor cross section: 2.5 mm², max. conductor cross section: 6 mm², rated voltage: 1500 V DC, rated current: 40 A, Connection method: Crimp, Contact connection type: Socket, min. cable diameter: 5 mm, max. cable diameter: 8 mm

Safety note
Safety note	• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
	• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
	WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
	• The products are suitable for applications in plant, controller, and electrical device engineering.
	• Assembled products may not be manipulated or improperly opened.
	• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
	• When using the product in direct connection with third-party manufacturers, the user is responsible.
	• For operating voltages > 50 V AC, conductive connector housings must be grounded
	• Ensure that the protective or functional ground has been properly connected.
	• Observe the corresponding technical data. You will find information: o On the product o On the packing label o In the supplied documentation o Online at phoenixcontact.com/products under the product
	• The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product.
	• Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products
	• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).
	• Operate the connector only when it is fully plugged in and interlocked.
	• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
	• Observe the minimum bending radius of the cable. Lay the cable without twisting it.

Product type	Connectors for energy storage
Product family	BPP
Number of positions	1
Data management status
Article revision	06
Insulation characteristics
Protection class	II
Degree of pollution	2

Rated voltage (II/2)	1500 V
Nominal voltage ATD	1500 V DC in accordance with IEC 62852:2014/AMD1:2020
Rated surge voltage	16 kV
Rated surge voltage (III/3)	16 kV
Rated current	40 A (in accordance with IEC 62852:2014/AMD1:2020)
Rated current (4.0 mm²)	34 A (in accordance with IEC 62852:2014/AMD1:2020)
Rated current (2.5 mm²)	27 A (in accordance with IEC 62852:2014/AMD1:2020)
Contact resistance	≤ 0.45 mΩ
Contact resistance	< 0.3 mΩ (Crimp to crimp)

Connection method	Crimp
Stripping length	8 mm

Width	20 mm
Height	20 mm
Length	72.8 mm

Color	red/black
Color of the housing part	black
Flammability rating according to UL 94	V0
Insulating material group	I
Insulating material	mPPE
Housing material	PPE
Cable seal material	EPDM
Contact material	Cu
Contact surface material	Ag
O-ring material	Silopren LSR 2660

External cable diameter	5 mm ... 8 mm
External cable diameter	5 mm ... 8 mm
Single wire, cross section	2.5 mm² 6 mm²
Stripping length of the individual wire	9 mm -1 mm
Cable pull-out force	> 80 N
Halogen-free	yes

Outside conductor diameter	5.00 mm 8.00 mm
Mechanical data
Outside conductor diameter	5.00 mm 8.00 mm
Insertion/withdrawal cycles	100
Insertion force	45 N ±10 N
Withdrawal force	250 N ±50 N (when locked)

Ambient conditions
Degree of protection	IP20 (Not plugged in)
	IP66/IP68 (2 m / 2 h) (plugged in)
Ambient temperature (operation)	-40 °C ... 85 °C (dependent on the derating curve)
Ambient temperature (assembly)	-5 °C ... 50 °C

Item number	1231074
Packing unit	50 pc
Minimum order quantity	50 pc
Product key	ABLDBB
GTIN	4063151331559
Weight per piece (including packing)	10.25 g
Weight per piece (excluding packing)	10.22 g
Country of origin	IN

Compatible products

Accessories

ECLASS-11.0	27440390
ECLASS-12.0	27440390
ECLASS-13.0	27440390

EU RoHS
Fulfills EU RoHS substance requirements	Yes (No exemptions)
China RoHS
Environment friendly use period (EFUP)	EFUP-E No hazardous substances above the limits
EU REACH SVHC
REACH candidate substance (CAS No.)	No substance above 0.1 wt%

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

ES-C1F-C-CO1 - Connector

1231074

Product details

ECLASS

ETIM

UNSPSC

TÜV Rheinland

Compatible products

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

ES-C1F-C-CO1 - Connector 1231074

Product details

ECLASS

ETIM

UNSPSC

Compatible products

PV-C PROTECTION CAP - Protective cap 1785430

PV-C3F-C-6-R3000 - Crimp contact 1050767

PV-C3F-C-2,5-4-R3000 - Crimp contact 1050769

CRIMPFOX-P SR 6 - Crimping pliers 1212755

ES-C1F-C-CO1 - Connector

1231074