Device connector, front mounting - M23-7EP198AA500S

Device connector, front mounting, M23 PRO, angled rotatable, for standard and ONECLICK fast locking system, M23, No. of pos.: 4+3+PE, type of contact: Pin, Crimp connection, flange dimensions: 26 mm x 26 mm

Product Details

Order information: Order crimp contacts 4 x Ø 1 mm, 4 x Ø 2 mm separately
Notes on operation Protective conductor housing connection according to DIN EN 61984 (VDE 0627)
Safety note
Safety note WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
• The products are suitable for applications in plant, controller, and electrical device engineering.
• When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
• Assembled products may not be manipulated or improperly opened.
• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at
• When using the product in direct connection with third-party manufacturers, the user is responsible.
• For operating voltages > 50 V AC, conductive connector housings must be grounded
• Ensure that the protective or functional ground has been properly connected.
• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
• Only use tools recommended by Phoenix Contact
• The installation notes/Design In documents online on the download page at must be observed for this product.
• Operate the connector only when it is fully plugged in and interlocked.
• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
• Observe the minimum bending radius of the cable. Lay the cable without twisting it.
• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).

Product type Circular connectors (device side)

Ambient temperature (operation) -40 °C ... 105 °C (see to derating)
Permanent temperature 125 °C (DIN EN 60512-9-2 / 1000 h)

Insulating body
Note Order information: Order crimp contacts 4 x Ø 1 mm, 4 x Ø 2 mm separately
Insulation body material PA 6.6
Insertion/withdrawal cycles 100
Connection method Crimp connection
Contact type Pin
Application Power
Number of positions 8
Connection profile 4+3+PE
Contact diameter Power contacts 2 mm
Power contacts min. 0.25 mm²
Power contacts max. 4 mm²
Rated current power 30 A
Note for max. connection cross section
Rated voltage 630 V
Rated surge voltage 6 kV
Overvoltage category III
Degree of pollution 3
Contact diameter Signal contacts 1 mm
Signal contacts min. 0.06 mm²
Signal contacts max. 1 mm²
Nominal current 9 A
Note for max. connection cross section
Rated voltage Signal contact 250 V
Rated surge voltage 4 kV
Overvoltage category III
Degree of pollution 3
Installation height 3000 m
Housing material GD-Zn
Flange dimensions 26 mm x 26 mm
Type of locking for standard and ONECLICK fast locking system
Degree of protection (plugged in) IP66 / IP68 (2m / 24h) / IP69K
Thread type M23

Flammability rating according to UL 94 V0

Item number 1628486
Packing unit 1 pc
Minimum order quantity 1 pc
Sales Key A12
Product Key ABRCIL
Catalog Page Page 147 (C-2-2019)
GTIN 4055626622170
Weight per Piece (including packing) 127.4 g
Weight per Piece (excluding packing) 112.17 g
Customs tariff number 85366990
Country of origin DE


ECLASS-9.0 27440103
ECLASS-10.0.1 27440109
ECLASS-11.0 27440109


ETIM 8.0 EC003569


UNSPSC 21.0 39121400

UL Listed

Approval ID: E468743-20190627

cUL Listed

Approval ID: E468743-20190627

cULus Listed

China RoHS Environmentally friendly use period: unlimited = EFUP-e
No hazardous substances above threshold values

Your advantages

Solutions with cross-manufacturer compatibility for standard and fast locking systems
Modern, consistent design for highly convenient operation
Crimping connection: vibration- and temperature-resistant assembly
All housing can be fitted with pin or socket contacts
Safe use in the field, thanks to high degree of protection