ES-FT-C4F-CO2 - Device connector front mounting

1231072

Device connector front mounting, Range of articles: BPP, color: blue/black, number of positions: 1, min. conductor cross section: 2.5 mm², max. conductor cross section: 6 mm², rated voltage: 1500 V DC, rated current: 38 A, Connection method: Crimp, Contact connection type: Socket, max. cable diameter: 5.8 mm

Product details

Safety note
Safety note	• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
	• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
	WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
	• The products are suitable for applications in plant, controller, and electrical device engineering.
	• Assembled products may not be manipulated or improperly opened.
	• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
	• When using the product in direct connection with third-party manufacturers, the user is responsible.
	• For operating voltages > 50 V AC, conductive connector housings must be grounded
	• Ensure that the protective or functional ground has been properly connected.
	• Observe the corresponding technical data. You will find information: o On the product o On the packing label o In the supplied documentation o Online at phoenixcontact.com/products under the product
	• The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product.
	• Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products
	• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).
	• Operate the connector only when it is fully plugged in and interlocked.
	• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
	• Observe the minimum bending radius of the cable. Lay the cable without twisting it.

Product type	Connectors for energy storage
Product family	BPP
Number of positions	1
Insulation characteristics
Protection class	II
Degree of pollution	2

Rated voltage (III/2)	1500 V
Nominal voltage ATD	1500 V DC in accordance with IEC 62852:2014/AMD1:2020
Rated surge voltage	16 kV
Rated surge voltage (III/3)	16 kV
Rated current	38 A (in accordance with IEC 62852:2014/AMD1:2020)
Rated current (4.0 mm²)	32 A (in accordance with IEC 62852:2014/AMD1:2020)
Rated current (2.5 mm²)	26 A (in accordance with IEC 62852:2014/AMD1:2020)
Contact resistance	< 0.45 mΩ (depending on the mating connector used)

Connection method	Crimp
Stripping length	8 mm
Tightening torque	1.8 ... 2.2 Nm

Width	21 mm
Height	21 mm
Length	49.1 mm

Color	blue/black
Color of the housing part	black
Material Seal	EPDM
Material Housing	PPE
Flammability rating according to UL 94	V0
Insulating material group	I
O-ring material	Silopren
Material for screw connection	PA

External cable diameter	5.8 mm
Single wire, cross section	2.5 mm² 6 mm²
Stripping length of the individual wire	9 mm -1 mm
Halogen-free	yes

Mechanical data
Insertion/withdrawal cycles	100
Insertion force	< 45 N ±10 N

Ambient conditions
Degree of protection	IP66/IP68 (2 m / 24 h) (plugged in)
	IP20 (Not plugged in)
	IP66/IP68 (2 m / 24 h)
Ambient temperature (operation)	-40 °C ... 85 °C
Ambient temperature (assembly)	-25 °C ... 50 °C

Standards/specifications	IEC 62852/UL 6703

Commercial data

Item number	1231072
Packing unit	50 pc
Minimum order quantity	50 pc
Sales key	ABLDAB
Product key	ABLDAB
GTIN	4063151331214
Weight per piece (including packing)	4.526 g
Weight per piece (excluding packing)	3.358 g
Country of origin	IN

Classifications

Approvals

Approval Specification Data
	Nominal voltage U_N	Nominal current I_N	Cross section AWG	Cross section mm²
	1500 V	50 A	14 - 10

Environmental product compliance

Compatible products

Accessories

EU RoHS
Fulfills EU RoHS substance requirements	Yes (No exemptions)
China RoHS
Environment friendly use period (EFUP)	EFUP-E No hazardous substances above the limits
EU REACH SVHC
REACH candidate substance (CAS No.)	Triphenyl phosphate (CAS: 115-86-6)
SCIP	9fe14281-cfc1-4859-aafc-eb73804d0ddb

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

ES-FT-C4F-CO2 - Device connector front mounting

1231072

Product details

ECLASS

ETIM

UNSPSC

TÜV Rheinland

UL Recognized

Compatible products

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

ES-FT-C4F-CO2 - Device connector front mounting 1231072

Product details

ECLASS

ETIM

UNSPSC

Compatible products

PV-FT-C-WALLMOUNT BK - Screw connection 1146092

PV-C PROTECTION CAP - Protective cap 1785430

PV-C3F-C-6-R3000 - Crimp contact 1050767

PV-C3F-C-2,5-4-R3000 - Crimp contact 1050769

CRIMPFOX-P SR 6 - Crimping pliers 1212755

ES-FT-C4F-CO2 - Device connector front mounting

1231072