Wireless set - ILB BT ADIO MUX-OMNI

Wireless MUX set, two modules with 16 digital inputs and outputs and 2 analog inputs and outputs (0 ... 20 mA, 0 ... 10 V) each, RSMA (female) antenna connection, incl. omnidirectional antennas with 1.5 m cable

Product Details

The Wireless MUX transmits 16 digital and 2 analog signals bidirectionally. The Wireless MUX is supplied ready to use: Unpack – connect – switch on – and you have a working wireless path.

Utilization restriction
EMC note EMC: class A product, see manufacturer's declaration in the download area

Type Block design
Product type Multiplexer
MTTF 1458 Years (SN 29500 standard, temperature 25°C, operating cycle 21%)
557 Years (SN 29500 standard, temperature 40°C, operating cycle 34.25%)
219 Years (SN 29500 standard, temperature 40°C, operating cycle 100%)
MTBF 465 Years (Telcordia standard, 25°C temperature, 21% operating cycle (5 days a week, 8 hours a day))
140 Years (Telcordia standard, 40°C temperature, 34.25% operating cycle (5 days a week, 12 hours a day))
Diagnostics messages Short-circuit or overload of the digital outputs LED
Wireless connection FS LED
Logic and actuator voltage LED
Link quality of the wireless connection 4 LEDs
Insulation characteristics
Overvoltage category II
Pollution degree 2
Switch-on time ≤ 3 s (Until the wireless connection is established)
Delay time ≤ 10 ms (Latency, typical)
≤ 800 ms (Failsafe function for wireless interruption)

Maximum power dissipation for nominal condition 2.4 W
Supply: Module electronics
Connection method Inline connector
Supply voltage 24 V DC
Supply voltage range 19.2 V DC ... 30.5 V DC (via power connector)
Current consumption 60 mA (Communications power at 24 V DC, 25 °C)
25 mA (Actuator supply, +load current Digital OUT (8 A))
Protective circuit Polarity protection, surge protection

Input name Analog inputs
Description of the input Single ended
Number of inputs 2
Current input signal 0 mA ... 20 mA
Input resistance current input 50 Ω
Voltage input signal 0 V ... 10 V
Input resistance of voltage input 130 kΩ
Measured value resolution 12 bits
Protective circuit Surge voltage; Suppressor diodes in the analog inputs, current limitation via internal protective circuit
Input name Digital inputs
Number of inputs 16
Connection method Spring-cage connection
Connection technology 1-conductor
Input voltage range "0" signal < 5 V
Input voltage range "1" signal > 15 V
Nominal input voltage UIN 24 V DC
Typical input current per channel 2.3 mA
Input frequency ≤ 10 Hz

Output name Analog outputs
Number of outputs 2
Protective circuit Transient protection
DAC resolution 12 Bit
Current output signal 0 mA ... 20 mA
Load/output load current output ≤ 500 Ω
Voltage output signal 0 V ... 10 V
Load/output load voltage output ≥ 2 kΩ
Output name Digital outputs
Connection method Spring-cage connection
Connection technology 1-conductor
Number of outputs 16
Protective circuit Short-circuit protection, overload protection, protected against reverse voltages
Output current 8 A (Total)
Maximum output current per channel 500 mA
Nominal output voltage 24 V DC
Output current when switched off ≤ 10 µA (When not loaded, a voltage can be measured even at an output that is not set.)
Nominal load, inductive 12 VA (1.2 H, 50 Ω)
Nominal load, lamp 12 W
Nominal load, ohmic 12 W (48 Ω)
Reverse voltage resistance to short pulses Reverse voltage proof
Behavior with overload Auto restart
Behavior with inductive overload Output can be destroyed
Behavior at voltage switch-off The output follows the power supply without delay

Conductor cross section, rigid 0.2 mm² ... 1.5 mm²
Stripping length 8 mm

Basic functions Multiplexers
Wireless licenses Europe, additional countries in the e-shop
Modulation type GFSK (Gaussian Frequency Shift Keying)
Antenna connection method RSMA (female)
No. of channels 40
Frequency range 2.402 GHz ... 2.48 GHz (ISM bandwidth)
Frequency band 2.4 GHz
Wireless standard Bluetooth
Transmission power 5 dBm
Receiver sensitivity -95 dBm

Diagnostic messages
Diagnostics Short-circuit or overload of the digital outputs
Message LED
Diagnostic messages
Diagnostics Wireless connection
Message FS LED
Diagnostic messages
Diagnostics Logic and actuator voltage
Message LED
Diagnostic messages
Diagnostics Link quality of the wireless connection
Message 4 LEDs

Dimensional drawing
Width 95 mm
Height 123.4 mm
Depth 57 mm
Note on dimensions with connectors

Color green
Housing material PA 6.6-FR

Ambient conditions
Ambient temperature (operation) -25 °C ... 60 °C
Degree of protection IP20
Air pressure (operation) 795 hPa ... 1080 hPa (up to 2000 m above sea level)
Air pressure (storage/transport) 66 kPa ... 108 kPa (up to 3500 m above sea level)
Ambient temperature (storage/transport) -25 °C ... 85 °C
Permissible humidity (operation) 95 % (non-condensing)
Permissible humidity (storage/transport) 95 %

Designation CE
Certificate CE-compliant
Designation EAC
Identification EAC
Designation UL, USA / Canada
Identification 508 Listed
Designation Wireless approval, Europe
Note RED 2014/53/EU
Designation Wireless approval USA, FCC
Identification YG3ADIOMUX
Note FCC directive, part 15.247
Designation Wireless approval India, WPC
Certificate NR-ETA/5957
Designation Wireless approval Japan, MIC
Identification Japan MIC (RF) ID:202-LSF002
Designation Wireless approval Canada, IC
Certificate 4720B-ADIOMUX
Note ISC directive RSS 210
Designation Wireless approval Mexico, IFT
Certificate IFT RCPPHIL19-2130
Designation Wireless approval South Africa, ICASA
Certificate TA-2006/032
Designation KC approval for South Korea
Certificate MSIP-CRI-PCK-2884208

Electromagnetic compatibility Conformance with EMC Directive 2014/30/EU
Electrostatic discharge
Standards/regulations EN 61000-4-2
Electrostatic discharge
Contact discharge ± 6 kV (Test Level 3)
Discharge in air ± 8 kV (Test Level 3)
Indirect discharge ± 6 kV
Comments Criterion B
Electromagnetic HF field
Standards/regulations EN 61000-4-3
Electromagnetic HF field
Frequency range 26 MHz ... 3 GHz (Test Level 3)
Field intensity 10 V/m
Comments Criterion A
Fast transients (burst)
Standards/regulations EN 61000-4-4
Fast transients (burst)
Input ± 2 kV (Test Level 3)
Signal ± 2 kV (Signal line)
Comments Criterion B
Surge current load (surge)
Standards/regulations EN 61000-4-5
Surge current load (surge)
Input ± 0.5 kV (symmetrical)
± 1 kV (asymmetrical)
Signal ± 1 kV (Signal line, asymmetrical)
Comments Criterion B
Conducted interference
Standards/regulations EN 61000-4-6
Conducted interference
Frequency range 0.15 MHz ... 80 MHz
Comments Criterion A
Voltage 10 V
Emitted interference
Emitted radio interference in acc. with EN 55011 EN 55016-2-3 Class A industrial applications
Criterion A Normal operating behavior within the specified limits.
Criterion B Temporary impairment to operational behavior that is corrected by the device itself.

Protection class III
Free from substances that could impair the application of coating according to P-VW 3.10.7 57 65 0 VW-AUDI-Seat central standard
Standards/specifications EN 300328
EN 61000-6-4
EN 61000-6-2
EN 62311
EN 60950

Mounting type DIN rail mounting

Item number 2884208
Packing unit 1 pc
Minimum order quantity 1 pc
Sales Key CN
Product Key DNC662
Catalog Page Page 386 (C-6-2019)
GTIN 4046356049597
Weight per Piece (including packing) 914 g
Weight per Piece (excluding packing) 885 g
Customs tariff number 85176200
Country of origin DE


ECLASS-9.0 27242602
ECLASS-10.0.1 27242602
ECLASS-11.0 27242602


ETIM 8.0 EC001597


UNSPSC 21.0 32151600


Approval ID: TR TS_D_01871-19


Approval ID: MSIP-CRI-PCK-2884208



Industry Canada

Approval ID: 4720B-ADIOMUX


Approval ID: 202-LSF002

REACh SVHC Lead 7439-92-1
China RoHS Environmentally Friendly Use Period = 50 years
For information on hazardous substances, refer to the manufacturer’s declaration available under “Downloads”

Your advantages

Wireless diagnostics by means of bar graph
Range of 50 m ... 100 m in industrial halls with omnidirectional antennas and up to 400 m outdoors with directional antennas
Quick connection establishment and signal transmission
Current Bluetooth 4.0 technology
Plug and play - startup without configuration
It couldn't be simpler: unpack – connect – switch on