M17-6EP1N8A6100S:P-040 - Device connector front mounting

1827005

This product needs further products for operation. Mandatory accessories

Product details

Technical data

Notes

Order information:	Order crimp contacts 5 x 0.6 mm, 4 x Ø 1 mm separately
Safety note
Safety note	WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
		• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
		• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
		• The products are suitable for applications in plant, controller, and electrical device engineering.
		• When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
		• Assembled products may not be manipulated or improperly opened.
		• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
		• When using the product in direct connection with third-party manufacturers, the user is responsible.
		• For operating voltages > 50 V AC, conductive connector housings must be grounded
		• Ensure that the protective or functional ground has been properly connected.
		• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
		• Only use tools recommended by Phoenix Contact
		• The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product.
		• Operate the connector only when it is fully plugged in and interlocked.
		• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
		• Observe the minimum bending radius of the cable. Lay the cable without twisting it.
		• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).

Product properties

Product type	Circular connectors (device side)

Material specifications

Flammability rating according to UL 94	V0

Connector

Housing
Thread type	M17
Design	straight
Type of locking	for standard and ONECLICK fast locking system
Mounting type	Front mounting (M18 x 0,75)
Assembly note	Central fastening
Housing material	GD-Zn
Seal material	FKM
Degree of protection (plugged in)	IP67

Environmental and real-life conditions

Ambient conditions
Ambient temperature (operation)	-40 °C ... 105 °C (see derating curve)

Commercial data

Item number	1827005
Packing unit	40 pc
Minimum order quantity	40 pc
Sales key	#####
Product key	ABRBAL
GTIN	4067923462779
Weight per piece (including packing)	33 g
Weight per piece (excluding packing)	23 g
Customs tariff number	85366990
Country of origin	DE

Classifications

Approvals

Approval Specification Data
	Nominal voltage U_N	Nominal current I_N	Cross section AWG
keine
Power	600 V	10 A	- 18
Signal	60 V	2 A	- 18

Approval Specification Data
	Nominal voltage U_N	Nominal current I_N	Cross section AWG
keine
Power	600 V	8 A	- 18
Signal	60 V	2 A	- 18

Environmental product compliance

Compatible products

Mandatory accessories

Accessories

Your advantages

Solutions with cross-manufacturer compatibility for standard and fast locking systems

Modern, consistent design for highly convenient operation

Crimping connection: vibration- and temperature-resistant assembly

All housing can be fitted with pin or socket contacts

Safe use in the field, thanks to high degree of protection

PHOENIX CONTACT Middle East FZ LLC

1201N-1206N, Dubai Science Park Towers - North, P.O. Box 345002, Dubai, United Arab Emirates

Ask a Question 800-7463649 info-me@phoenixcontact.com

ECLASS-13.0	27440109
ECLASS-15.0	27440109

EU RoHS
Fulfills EU RoHS substance requirements	Yes (No exemptions)
China RoHS
Environment friendly use period (EFUP)	EFUP-E No hazardous substances above the limits
EU REACH SVHC
REACH candidate substance (CAS No.)	No substance above 0.1 wt%

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

M17-6EP1N8A6100S:P-040 - Device connector front mounting

1827005

Product details

ECLASS

ETIM

UL Listed

cUL Listed

Compatible products

Your advantages

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

M17-6EP1N8A6100S:P-040 - Device connector front mounting 1827005

Product details

ECLASS

ETIM

Compatible products

ST-10KP010 - Crimp contact 1618255

ST-10KP035 - Crimp contact 1618458

M17PRO-VIB-ORING - Sealing ring 1431550

ST-E2015151 - Flat nut 1613831

PROT-M17PRO-OT-IP20 - Plastic protective cap 1055708

Your advantages

Frequently searched

M17-6EP1N8A6100S:P-040 - Device connector front mounting

1827005