VS-FSBPYS-OE-94H/10,0 SCOX - Device connector rear mounting - 1239507

Notes

Notes on operation	The electrical and mechanical data specified assume that the connector pair is correctly locked and mounted. If the connector is unlocked and if there is a danger of contamination, the connector must be sealed using a protective cap > IP54. Influences arising from litz wires, cables or PCB assembly must also be taken into consideration.
Safety note
Safety note	WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
		• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
		• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
		• The products are suitable for applications in plant, controller, and electrical device engineering.
		• When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
		• Assembled products may not be manipulated or improperly opened.
		• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
		• When using the product in direct connection with third-party manufacturers, the user is responsible.
		• For operating voltages > 50 V AC, conductive connector housings must be grounded
		• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
		• Observe the corresponding technical data. You will find information: o On the product o On the packing label o In the supplied documentation o Online at phoenixcontact.com/products under the product
		• Only use tools recommended by Phoenix Contact
		• Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products
		• Ensure that the protective or functional ground has been properly connected.
		• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
		• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).

Product properties

Product type	Data cable preassembled
Sensor type	Ethernet hybrid
Number of positions	8
Coding	Y
Insulation characteristics
Overvoltage category	II
Degree of pollution	3

Interfaces

Signal type/category	Ethernet hybrid CAT5 (IEC 11801:2002), 100 Mbps

Electrical properties

Nominal voltage U_N	48 V AC (Power and data)
	50 V DC (Power and data)
Nominal current I_N	0.5 A (Data)
	6 A (Power)
Transmission medium	Copper
Transmission speed	100 Mbps
Transmission characteristics (category)	CAT5 (IEC 11801:2002)

Mechanical properties

Mechanical data
Insertion/withdrawal cycles	≥ 100

Material specifications

Material	Zinc die-cast (nickel-plated)
Flammability rating according to UL 94	V0
Seal material	FKM
Contact material	CuZn
Contact surface material	Ni/Au
Contact carrier material	PA 6.6
Material for screw connection	Brass, nickel-plated

Connection data

Connection technology
Connection method	Hybrid cable
Conductor connection
Connection method	Hybrid cable
Tightening torque	2 Nm ... 3 Nm (Installation-side)

Connector

Connection 1
Head design	Socket
Head cable outlet	straight
Head thread type	M12
Head locking type	SPEEDCON
Coding	Y
Connection 2
Head design	free cable end

Cable/line

Ethernet hybrid [94H]
Cable weight	87 kg/km
UL AWM Style	21815 (80°C/300 V)
Number of positions	8
Shielded	yes
Cable type	Ethernet hybrid [94H]
Conductor structure	1x4xAWG26 + 1x4xAWG20
Conductor structure signal line	19x 0.10 mm
AWG signal line	26
Conductor structure, voltage supply	19x 0.20 mm
AWG power supply	20
Conductor cross section	4x 0.15 mm² (Data)
Conductor cross section		4x 0.6 mm² (Power)
Wire diameter incl. insulation	1.05 mm (Data)
Wire diameter incl. insulation		1.4 mm (Power)
External cable diameter	7.60 mm ±0.2 mm
Outer sheath, material	PUR
External sheath, color	black RAL 9005
Conductor material	Bare Cu litz wires
Material wire insulation	PP (Data)
Material wire insulation		PP (Power)
Single wire, color	white/orange, orange, white/green, green, white, blue, brown, black
Overall twist	1 star quad and 4 wires with 2 fillers
Optical shield covering	85 %
Insulation resistance	≥ 5 GΩ*km
Loop resistance	≤ 280.00 Ω/km (Data)
Loop resistance		≤ 34.60 Ω/km (Power)
Wave impedance	100 Ω ±15 Ω (4 MHz ... 100 MHz)
Working capacitance	nom. 50 nF (per kilometer)
Differential impedance	100 Ω ±5 % (at 100 MHz)
Nominal voltage, cable	≤ 300 V (Peak value, not for high-power applications)
Test voltage Core/Core	2000 V (50 Hz, 1 min.)
Test voltage Core/Shield	2000.00 V (50 Hz, 1 min.)
Minimum bending radius, fixed installation	5 x D
Minimum bending radius, flexible installation	10 x D
Smallest bending radius, fixed installation	38 mm
Smallest bending radius, movable installation	76 mm
Dynamic load capacity (bending)	Max. bending cycles: 2000000, Traversing path: 4.5 m, Traversing rate: 3 m/s, Acceleration: 4 m/s²
Tensile strength	70 N (in accordance with DIN EN 50565-1 for flexible installation)
Tensile strength		240 N (in accordance with DIN EN 50565-1 for fixed installation)
Near end crosstalk attenuation (NEXT)	56.3 dB (at 4 МHz)
		50.3 dB (at 10 MHz)
		47.2 dB (at 16 MHz)
		45.8 dB (at 20 МHz)
		42.9 dB (at 31.25 МHz)
		38.4 dB (at 62.5 МHz)
		35.3 dB (at 100 MHz)
Shield attenuation	6 dB (at 4 МHz)
		9.5 dB (at 10 MHz)
		12.1 dB (at 16 MHz)
		13.5 dB (at 20 МHz)
		17.1 dB (at 31.25 МHz)
		24.8 dB (at 62.5 МHz)
		32 dB (at 100 MHz)
		≥ 80.00 dB (30 MHz ... 125 MHz)
Halogen-free	according to IEC 60754
Halogen-free		in accordance with DIN VDE 0472 part 815
Flame resistance	in accordance with UL 2556, Section 9.1 and UL 1581, Section 1100
Flame resistance		in accordance with UL 2556, Section 9.3 and UL 1581, Section 1060
Resistance to oil	in accordance with IEC 60811-404
Resistance to oil		According to DIN EN 50363-10-2
Other resistance	Low adhesion
Special properties	Free of substances which would hinder coating with paint or varnish
Special properties		Silicone-free
Ambient temperature (operation)	-40 °C ... 80 °C (cable, fixed installation)
Ambient temperature (operation)		-30 °C ... 70 °C (Cable, flexible installation)

Environmental and real-life conditions

Ambient conditions
Degree of protection	IP67
	IP65/IP67
Ambient temperature (operation) (male connector/female connector)	-25 °C ... 80 °C (Plug / socket)
	-40 °C ... 80 °C (without mechanical actuation)

Standards and regulations

M12
Standard designation	M12 connector
Standards/specifications	IEC 61076-2-113

Item number	1239507
Packing unit	1 pc
Minimum order quantity	50 pc
Product key	ABQDGI
GTIN	4063151392765
Weight per piece (including packing)	904.6 g
Weight per piece (excluding packing)	904.6 g
Country of origin	DE

EU RoHS
Fulfills EU RoHS substance requirements	Yes (No exemptions)
China RoHS
Environment friendly use period (EFUP)	EFUP-E No hazardous substances above the limits
EU REACH SVHC
REACH candidate substance (CAS No.)	No substance above 0.1 wt%

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

VS-FSBPYS-OE-94H/10,0 SCOX - Device connector rear mounting

1239507

Product details

ECLASS

ETIM

Compatible products

Your advantages

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

VS-FSBPYS-OE-94H/10,0 SCOX - Device connector rear mounting 1239507

Product details

ECLASS

ETIM

Compatible products

PROT-M12 - Screw plug 1680539

PROT-M12 SH - Screw plug 1503302

PROT-M12 FB - Screw plug 1555538

CUTFOX 12 - Cable-cutting tool 1212128

CUTFOX-S VDE - Diagonal cutter 1212207

VS-CABLE-STRIP-VARIO - Stripping tool 1657407

MICROFOX-SP-1 - Diagonal cutter 1212487

WIREFOX 4 - Stripping tool 1212156

WIREFOX-E 4 - Stripping tool 1212704

WIREFOX 10 - Stripping tool 1212150

WP-CTA POM 13,0 BK - Protective hose adapter 1422884

WP-PA HF 13,0 BK - Protective hose 3240681

WP-PA HF-HB 13,0 BK - Protective hose 3240839

Your advantages

VS-FSBPYS-OE-94H/10,0 SCOX - Device connector rear mounting

1239507