Repeater - PSI-REP-DNET CAN
2313423

Modular repeater for electrical isolation and increasing the range for DeviceNet/SDS/CANopen, data rate of up to 1 Mbps. High-quality electrical isolation between the interfaces, DIN-rail mountable, 24 V DC supply.


Product Details


The performance and availability of bus systems can be significantly increased by using repeaters. In addition to electrical isolation, bus segmentation with repeaters makes it possible to multiply the permissible coverage of the network and to extend the number of devices.



Utilization restriction
EMC note EMC: class A product, see manufacturer's declaration in the download area
Utilization restriction
CCCex note Use in potentially explosive areas is not permitted in China.

Product type Interface converter
MTTF 1091 Years (SN 29500 standard, temperature 25°C, operating cycle 21%)
514 Years (SN 29500 standard, temperature 40°C, operating cycle 34.25%)
208 Years (SN 29500 standard, temperature 40°C, operating cycle 100%)
MTBF 823 Years (Telcordia standard, 25°C temperature, 21% operating cycle (5 days a week, 8 hours a day))
170 Years (Telcordia standard, 40°C temperature, 34.25% operating cycle (5 days a week, 12 hours a day))

Electrical isolation VCC // TBUS // CAN A // CAN B
Maximum power dissipation for nominal condition 1.32 W
Test voltage data interface/power supply 1.5 kVrms (50 Hz, 1 min.)
Supply
Supply voltage range 10 V DC ... 30 V DC (via pluggable COMBICON screw terminal block)
Nominal supply voltage 24 V DC
Typical current consumption 55 mA (24 V DC)
Max. current consumption 80 mA
≤ 2 A (For operation in a joining station, via the DIN rail connector)
Function
Status and diagnostic indicators LEDs: VCC (supply voltage), NET A (Mod/Net status port A), NET B (Mod/Net status port B), ACT (activity/data traffic)

Output name Relay output
Number of outputs 1
Contact type N/O contact
Minimum switching voltage 10 V DC
Maximum switching voltage 30 V DC
Limiting continuous current 500 mA

Supply
Torque 0.56 Nm ... 0.79 Nm

Bit distortion, input ± 35 %
Bit distortion, output < 6.25 %
Bit delay One telegram length (EXTENDED)
Signal CAN
CANopen®
DeviceNet™
Data: CAN interface, in accordance with ISO/IS 11898 for DeviceNet, CAN, CANopen
Transmission speed ≤ 1 Mbps (Configurable via DIP switches)
Connection method COMBICON plug-in screw terminal block
No. of channels 2 (CAN_High / CAN_Low)
Transmission length ≤ 5000 m (Dependent on the data rate and the protocol used)
Number of bus devices ≤ 64 (per potential segment)
≤ 63 (DeviceNet™, can be addressed logically)
≤ 128 (CANopen®, can be addressed logically)
Termination resistor 124 Ω (Integrated and ready to be switched)
Conductor cross section flexible max. 2.5 mm²
Conductor cross section flexible min. 0.2 mm²
Conductor cross section solid max. 2.5 mm²
Conductor cross section solid min. 0.2 mm²
Conductor cross section AWG max. 14
Conductor cross section AWG min. 24
Transmission medium 2-wire twisted pair, shielded
Transmission method CSMA/CA
File format/coding Bit stuffing, NRZ
Data: CAN interface, in accordance with ISO/IS 11898 for DeviceNet, CAN, CANopen
Transmission speed ≤ 1 Mbps (Configurable via DIP switches)
Connection method COMBICON plug-in screw terminal block
No. of channels 2 (CAN_High / CAN_Low)
Transmission length ≤ 5000 m (Dependent on the data rate and the protocol used)
Number of bus devices ≤ 64 (per potential segment)
≤ 63 (DeviceNet™, can be addressed logically)
≤ 128 (CANopen®, can be addressed logically)
Termination resistor 124 Ω (Integrated and ready to be switched)
Conductor cross section flexible max. 2.5 mm²
Conductor cross section flexible min. 0.2 mm²
Conductor cross section solid max. 2.5 mm²
Conductor cross section solid min. 0.2 mm²
Conductor cross section AWG max. 14
Conductor cross section AWG min. 24
Transmission medium 2-wire twisted pair, shielded
Transmission method CSMA/CA
File format/coding Bit stuffing, NRZ

Dimensional drawing
Width 35 mm
Height 111 mm
Depth 121 mm

Color green
Material PA 6.6-FR (Housing)

Ambient conditions
Degree of protection IP20
Ambient temperature (operation) -20 °C ... 60 °C
Ambient temperature (storage/transport) -40 °C ... 85 °C
Altitude ≤ 5000 m (For restrictions, see the manufacturer's declaration for altitude operation)
Permissible humidity (operation) 30 % ... 95 % (non-condensing)

CE
Designation CE
Certificate CE-compliant
CE
Designation EAC
Identification EAC
CE
Designation ATEX
Identification  II 3 G Ex nA IIC T4 Gc X
Note Please follow the special installation instructions in the documentation!
CE
Designation UL, USA / Canada
Identification 508 Listed
CE
Designation Corrosive gas test
Identification ISA-S71.04-1985 G3 Harsh Group A
CE
Designation Shipbuilding
Identification DNV GL
DNV GL data
Temperature B
Humidity A
Vibration A
EMC B
Enclosure Required protection according to the Rules shall be provided upon installation on board

Electromagnetic compatibility Conformance with EMC Directive 2014/30/EU
Noise emission EN 55011
Noise immunity EN 61000-6-2
Electrostatic discharge
Standards/regulations EN 61000-4-2
Electrostatic discharge
Contact discharge ± 6 kV
Discharge in air ± 8 kV
Comments Criterion B
Electromagnetic HF field
Standards/regulations EN 61000-4-3
Electromagnetic HF field
Frequency range 80 MHz ... 3 GHz
Field intensity 10 V/m
Comments Criterion A
Fast transients (burst)
Standards/regulations EN 61000-4-4
Fast transients (burst)
Input ± 2 kV
Signal ± 2 kV
Comments Criterion B
Surge current load (surge)
Standards/regulations EN 61000-4-5
Surge current load (surge)
Input ± 0.5 kV
Signal ± 1 kV
Comments Criterion B
Conducted interference
Standards/regulations EN 61000-4-6
Conducted interference
Comments Criterion A
Voltage 10 V
Emitted interference
Standards/regulations EN 55011
Comments Class A, industrial applications
Criterion A Normal operating behavior within the specified limits.
Criterion B Temporary impairment to operational behavior that is corrected by the device itself.

Free from substances that could impair the application of coating according to P-VW 3.10.7 57 65 0 VW-AUDI-Seat central standard

Mounting type DIN rail mounting

Item number 2313423
Packing unit 1 pc
Minimum order quantity 1 pc
Sales Key CN
Product Key DNC123
Catalog Page Page 423 (C-6-2019)
GTIN 4046356428392
Weight per Piece (including packing) 233.466 g
Weight per Piece (excluding packing) 233.466 g
Customs tariff number 85176200
Country of origin DE


ECLASS

ECLASS-9.0 27242208
ECLASS-10.0.1 27242208
ECLASS-11.0 27242208

ETIM

ETIM 8.0 EC001423

UNSPSC

UNSPSC 21.0 32151700

EAC

Approval ID: EAC-Zulassung

DNV GL

Approval ID: TAA00001KR
Approval Specification Data
Nominal Voltage UN Nominal Current IN Cross Section AWG Cross Section mm2

EAC

Approval ID: RU *-DE.A*30.B.01735

UL Listed

Approval ID: FILE E 238705

cUL Listed

Approval ID: FILE E 238705

ATEX

Approval ID: PxCIF07ATEX2313533X

cULus Listed


REACh SVHC Lead 7439-92-1
China RoHS Environmentally Friendly Use Period = 50 years
For information on hazardous substances, refer to the manufacturer’s declaration available under “Downloads”

Your advantages

Automatic data rate detection or fixed data rate setting via DIP switches
Data rates of up to 1 Mbps
High-quality 4-way isolation between all interfaces
Can be combined with PSI-MOS FO converters in a modular way thanks to DIN rail connectors
All connections can be plugged in using a COMBICON screw terminal block
Approved for use in zone 2
Shipbuilding approval in accordance with DNV GL