WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
• The products are suitable for applications in plant, controller, and electrical device engineering.
• When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
• Assembled products may not be manipulated or improperly opened.
• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
• When using the product in direct connection with third-party manufacturers, the user is responsible.
• For operating voltages > 50 V AC, conductive connector housings must be grounded
• Only use tools recommended by Phoenix Contact
• The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product.
• Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products
• Operate the connector only when it is fully plugged in and interlocked.
• Operate the connector only when it is fully plugged in.
• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
• Observe the minimum bending radius of the cable. Lay the cable without twisting it.
• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
Product type
Data connector (cable side)
Application
INTERBUS
Type
D-SUB
Number of positions
9
Connection profile
D-SUB
No. of cable outlets
2
Shielded
yes
Cable outlet
slanted
Insulation characteristics
Overvoltage category
II
Degree of pollution
2
Rated voltage (III/3)
63 V
Rated surge voltage
0.5 kV
Rated current
1 A
Transmission medium
Copper
Connection technology
Connection method
Screw connection
Connection cross section AWG
26 ... 20
Conductor cross-section
0.14 mm² ... 0.5 mm²
Signal type/category
INTERBUS
Color
blue
Flammability rating according to UL 94
V0
Housing material
Plastic
Cable seal material
CR/NBR
Contact material
Copper alloy
Contact surface material
Gold over nickel
Contact carrier material
PBTP
External cable diameter
5 mm ... 9 mm
Cable cross section
0.14 mm²
Mechanical data
Insertion/withdrawal cycles
≥ 200
Ambient conditions
Degree of protection
IP20
Ambient temperature (operation)
-20 °C ... 70 °C
Item number
1689284
Packing unit
1 pc
Minimum order quantity
1 pc
Sales key
ABN
Product key
ABNCBA
GTIN
4017918892753
Weight per piece (including packing)
92.8 g
Weight per piece (excluding packing)
72.642 g
Customs tariff number
85369010
Country of origin
DE
ECLASS
ECLASS-13.0
27440290
ECLASS-15.0
27440322
ETIM
ETIM 10.0
EC001132
UNSPSC
UNSPSC 21.0
39121400
EU RoHS
Fulfills EU RoHS substance requirements
Yes
Exemption
6(c)
China RoHS
Environment friendly use period (EFUP)
EFUP-50
An article-related China RoHS declaration table can be found in the download area for the respective article under "Manufacturer declaration". For all articles with EFUP-E, no China RoHS declaration table issued and required.
